• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.583-585
• /
• 2000

This study reports the fluidic handling method using hydrophobic patterns inside PDMS microchannels. In order to obtain hydrophobic patterns, we pattern fluorcarbon(FC) film surfaces by lift-off process. FC films are deposited by spin coating method and plasma polymerization method. Hydrophobic surfaces are used as the barriers to control fluid flow. Injected liquid is spontaneously filled up inside PDMS-microchannels by the capillary action. Liquid flow stops when it meets hydrophobic regions which can be the barrier against fluid flow. Then, again, when liquid is pressurized externally, liquid can move toward another hydrophilic region by external air pressure. Contact angle analyses are performed on fluorocarbon films to estimate the wettability of film surfaces.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.6
• /
• pp.490-496
• /
• 2001

An experimental study on the behavior of the water hold-up by condensation of a fin-and-tube heat exchanger with regard to the surface characteristics, i.e., contact angle, was conducted. The static and dynamic contact angles were measured, and condensation experiments were conducted. Flow patterns on the fins with different surface characteristics were visualized. Results showed that the static contact angle is proportional to the dynamic contact angle within the range of this study. The water hold-up of the heat exchanger increases as the static or dynamic contact angle of its surfaces increases. Existence of transition of flow patterns was found as the static or dynamic angle increase. Due to the transition in the flow patterns, changes in the gradient of the water hold-up is occurred around the static angle of 8$0^{\circ}C$.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.1 s.62
• /
• pp.8-13
• /
• 2005

In a multiple array of vertical cylinders, flaw patterns are very complex and very interactive between cylinders. The patterns are turbulent and non-linear depending on various factors. The gap and flow incoming velocity of upstream can affect on the downstream cylinder. In this study, the flaw characteristics around two vertical cylinders are investigated numerically and experimentally. As the gap between cylinders is changed at fixed coming velocity, the pressure distributions around cylinders are observed and compared by experimental and numerical approaches. The F.D.M and multi-block method are applied in the study. The pressures at 12 points around the cylinder are measured in the experiment. The results can be applied in the understanding and design of multiple pile array structures.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.4 no.2
• /
• pp.59-75
• /
• 1986

The purpose of this study is to determine the most effective image analysis technique for extraction of coastal flow patterns from LANDSAT MSS data. Choosing the coastal area of Incheon, LANDSAT MSS data of oceanic area, which has generally low values of CCT data in comparison with the adjacent land was used On the basis of the above preparation, the most effective image analysis procedure of LANDSAT MSS data for the case of extraction of coastal flow patterns has been obtained through contrast stretching, color composite, and compression of bi-band image data.

• Journal of Korean Society on Water Environment
• /
• v.31 no.2
• /
• pp.196-208
• /
• 2015

This study analyzed the characteristics of sewer flow and its water quality, and investigated changes in the characteristics in three areas where the sewer rehabilitation projects have been carried out. In S1 area, the patterns of the flow became regular and the range of the fluctuation decreased after the sewer rehabilitation. The flow and its BOD concentration increased. The infiltration/inflow and exfiltration showed clear distinction before and after the sewer rehabilitation in this area. In S2 area, the patterns and the range of the fluctuation of the flow made no differences before and after the sewer rehabilitation. The flow decreased slightly and its BOD concentration increased considerably after the sewer rehabilitation. Big decrement in stormwater inflow but small in exfiltration appeared in this area. In S3 area, the patterns and the range of the fluctuation of the flow made no differences before and after the sewer rehabilitation. The flow decreased slightly and its BOD concentration increased in a small rate in this area.

• Journal of the Korean Society of Visualization
• /
• v.15 no.1
• /
• pp.11-18
• /
• 2017

A two-phase flow observed in a heat exchanger or nuclear power generation often has a profound effect on undesirable noise or flow characteristics. Void fraction, which refers to the ratio of gas (or liquid) to the total fluid, affects heat transfer coefficient, vibration and so forth. In other words, void fraction is one of most important parameters in two-phase flow since it contributes to comprehend the characteristics of two-phase flow. We developed a two-phase flow visualization system to measure cross-sectional and volumetric void fractions by using quick closing valves and image processing software. With this system, we could observe the plug, slug, and stratified flow patterns of two-phase flow and measure a myriad of void fractions. As a consequence of the experiment, we found that the estimated void fractions were largely coincident with the predictive values by Chisholm model.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.211-216
• /
• 2001

Flow motion and variation of thermal field around a bubble which attached at the upper cooled solid wall in a $B\dot{e}nard$ convection flow is studied experimentally using thermo-sensitive liquid-crystal tracers and image processing for flow visualization and analysis. The air is injected gradually by $0.1m\ell$ to make the bubble. As the growing of the bubble in a $B\dot{e}nard$ convection flow, the variation of temperature field and surface tension along the bubble, which in turn cause to change the thermal field patterns and the flow direction and patterns. 6 cells flow pattern is transformed into diverse flow pattern. At the large size of a bubble, it's only conduction mechanism under the region of the bubble because of low Ra number 1137, but the convection flow both sides of the bubble leads to another convection flow in the bubble influence area which has been remained stable stagnation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.142-147
• /
• 2004

The flow in the LOX manifold of liquid rocket has been investigated using a CAE technique with an objective of economical modeling of injection holes in order to reduce the overall computational cost of flow analysis during the optimal rocket design procedure. The computational geometry is very close to that of the actual rocket design and the flow condition through the injection holes resembles that in the actual manifold of the liquid rocket. The result shows that the flow in the plane just above the injection holes is not uniformly distributed in terms of pressure and mass flow rate and this is attributed to the large-scale flow patterns present the LOX manifold. Thus, the flow physics should be understood correctly before making any attempt to model the injection holes. In the present study, several boundary conditions which were designed to effectively replace the presence of injection holes have been tested and it was found that a simple modeling can be possible by mimicking the actual geometry of the injection holes. By using this simple injection hole modeling, it was able to obtain about 30% reduction in computational cost but it was still able to reproduce the flow patterns correctly. Also the flow has been analyzed after incorporating a couple of different types of pre-distributors in LOX manifold and the effect of those will be discussed.

• Transactions of Materials Processing
• /
• v.14 no.1 s.73
• /
• pp.49-56
• /
• 2005

In the semi-solid die casting process, an important thing is the flow behavior of semi-solid materials. The flow patterns of the semi-solid material can make the defects during die filling. To control the flow patterns is very important and difficult. In this paper, the flow behavior of the semi-solid A356 alloy material during die filing at various die gate shapes has been observed with the grain size controlled material. The effect of the gate shape on the die filling characteristics was investigated. The filling tests in each plunger stroke were experimented, and also simulated on the semi-solid material die casting process by MAGMAsoft. According to the filling tests and computer simulation, the effect of the gate shape on liquid segregation has been investigated.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.18 no.4
• /
• pp.86-91
• /
• 2010

New Design configurations of the fighter aircraft igloo diffuser were studied based on the closed ventilation type in contrast to the conventional open distribution type. To validate the enhanced and safe performance, the exhaust flow patterns of the two igloo diffuser types were simulated by both experimental and computational approaches as design tools. Flow visualizations were conducted to investigate the exhaust flow patterns in experimental approach. In addition, the commercial code called Fluent was used to calculate flow field properties. Computational simulations provided detailed parametric studies that significantly reduced the amount of experimentation necessary to alter the design parameters of the existing fighter igloo diffuser. The closed ventilation type of the igloo diffuser was shown the better results.