• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.6
• /
• pp.548-554
• /
• 2012

Verification and validation of operational software of the flight control computer, which is flight safety critical, is very important to prove correctness and faultness of the software. To verify the real-time softare requirement on operational software of flight control computer, real-time software internal parameter and variable monitoring technics on hardware-in-the-loop environment, similar to on-flight environment, is required. This paper describes flight safety critical software validation and verificiation environment using standard debugging interface, NEXUS 5001.

• International Journal of Aeronautical and Space Sciences
• /
• v.5 no.1
• /
• pp.57-63
• /
• 2004

UAV(Unmanned Aerial Vehicle) has become one of the most popularmilitary/commercial aerial robots in the new millennium. In spite of all theadvantages that UAVs inherently have, it is not an easv job to develop a UAVbecause it requires very systematic and complete approaches in full developmentenvelop. The ground test and evaluation phase has the utmost importance in thesense that a well-developed system can be best verified on the ground. In addition,many of the aircraft crashes in the flight tests were resulted from the incompletedevelopment procedure. In this research, a verification procedure of the wholeairbome integrated system was conducted including the flight management system.An airbome flight control computer(FCC) senses the extemal environment from thepehpheral devices and sends the control signal to the actuating system using theassigned control logic and flight test strategy. A ground test station controls themission during the test while the downlink data are transferred from the flightmanagement computer using the serial communication interface. The pilot controlbox also applies additional manual actuating commands. The whole system wastested/verified on the wind-tunnel system, which gave a good pitch controlperformance with a preUspecified flight test procedure. The ground test systemguarantees the performance of fundamental functions of airbome electronic systemfor the future flight tests.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.7
• /
• pp.701-708
• /
• 2009

The flight control law of developed flight control computer(DFLCC) is developed based on operation flight program of advanced trainer aircraft full scale development final configuration. The flight control law design is used common use development tool in GUI(Graphic User Interface) environment. The flight control law transformed to C-Code is reflected in OFP. The OFP is verified by the standardized verification process. But, before standardized verification process, we need preliminary verification process such as similarity of flight control law and reliability of developed HILS. Similarity of flight control law is verified by comparing the aircraft response of advanced trainer aircraft and those of the developed control law. Also, reliability of developed HILS is verified by comparing the aircraft response of HILS and Non-real time simulation result. This paper verifies similarity of developed control law and reliability of HILS environment as comparing aircraft response.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.12
• /
• pp.857-866
• /
• 2022

Fixed-wing UAVs have long endurance and range capabilities compared to other aerial platforms. These advantages led fixed-wing UAVs to become a popular platform for reconnaissance missions in the military. In this research, we modeled fixed-wing UAVs, including the landing gear model and developed a guidance and control system for flight control computers to construct a HILS environment. We also developed an autopilot system that includes automated take-off, cruise, and landing control for UAVs. We also retrived the Aerodynamic coefficients an UAV using Datcom and AVL software and used them for 6 degrees of freedom modeling. The Flight control computer calculates guidance commands using the Carrot chasing guidance law after distinguishing the condition of the UAV based on 16 pre-defined flight modes and calculates control inputs using Nonlinear Dynamic Inversion (NDI) control scheme. We used RTNngine to integrate the Simulink model and flight control computer for HILS environment formulation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.7
• /
• pp.574-581
• /
• 2001

In this paper we design and evaluate the longitudinal nonlinear N(aub)z-CSAS(Command and Stability Augmentation System) flight control law in \"DMI(Dynamic Model Inversion)-method\" and classical \"Gain Scheduling-method\", respectively, to meet the handling quality requirements associated with push-over pull-up maneuver. It is told that the flight control law designed in \"DM-method\" is adequate to the full flight regime without gain scheduling and is efficient to produce the time response shape desired to the handling quality requirements. On the contrary, the flight control law designed in \"Gain Scheduling-method\" is easy to be implemented in flight control computer and insensitive to variation of the actuator model characteristics.n of the actuator model characteristics.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.2
• /
• pp.169-179
• /
• 2010

Satisfying the same probability of loss of control and essentially two fail operative performance with a triplex computer architecture requires a lot of modification of the conventional redundancy management design techniques, previously employed in quadruplex digital flight control computer. T-50 FCS for triplex redundancy management design applied an advanced digital flight control architecture with an I/O controller which is functionally independent of the digital computer to achieve the same reliability and special failure analysis and isolation schemes for fail operational goals with a triplex configuration. The analysis results indicated that the triplex flight control system is to satisfy the safety requirement utilizing the advanced flight control techniques and the system performance of the implemented flight control system was verified by failure mode effect test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.2
• /
• pp.133-139
• /
• 2017

Flight control computer of tiltrotor UAV was designed by redundancy system with primary and secondary channels to improve reliability. The redundancy functions consist of channel switching and data recovery. The channel switching function consists of software method by using cross channel data link and hardware method by using watchdog timer. The data recovery is the function to maintain flight condition when the flight control computer is restarted exceptionally in operation. The redundancy system was verified by flight control computer bench test, system integration test and HILS test. This paper describes the redundancy function of tiltrotor UAV flight control computer and test-verification method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.9
• /
• pp.759-765
• /
• 2016

This paper presents the principle, dynamics modeling and control, hardware implementation, and flight test result of a hybrid-type unmanned aerial vehicle (UAV). The proposed UAV was designed to provide both hovering and fixed-wing type aerodynamic flight modes. The UAV's flight mode transition was achieved through the attitude transformation in pitch axis, which avoids a complex rotor tilt mechanism from a structural and control viewpoint. To achieve this, a different navigation coordinate was introduced that avoids the gimbal lock in pitch singularity point. Attitude and guidance control algorithms were developed for the flight control system. For flight test purposes, a quadrotor attached with a tailless fixed-wing structure was manufactured. An onboard flight control computer was designed to realize the navigation and control algorithms and the UAV's performance was verified through the outdoor flight tests.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.3
• /
• pp.425-436
• /
• 2015

This paper presents the procedures used for estimating the stability and control derivatives of a general aviation canard aircraft from flight data. The maximum likelihood estimation method which accounts for both process and measurement noise was used for the flight data analysis of a four seat canard aircraft, the Firefly. Without relying on the parameter estimation method, several aerodynamic derivatives were obtained by analyzing the steady state flight data. A wind tunnel test, a flight test of a 1/4 scaled remotely controlled model aircraft, and the prediction of aerodynamic coefficients using the USAF Stability and Control Digital Data Compendium (DATCOM), Advanced Aircraft Analysis (AAA), and Computer Fluid Dynamics (CFD) were performed during the development phase of the Firefly and the results were compared with flight determined derivatives of a full scaled flight prototype. A correlation between the results from each method could be used for the design of the canard aircraft as well as for building the aerodynamic database.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.1063-1067
• /
• 1993

Fuzzy logic is applied to a roll autopilot for missiles. Fuzzy rules are made so that the response duplicates that of the conventional control law for some flight condition. A scaling factor of the fuzzy controller is then scheduled by the missile velocity and altitude information to cope with the variation of the roll dynamics from that flight condition. By computer simulations and calculation of the stability margin, it is shown that the fuzzy control is robuster than the conventional one over the flight envelope even though two control laws work similarly for some flight conditions.