• Journal of Aerospace System Engineering
• /
• v.8 no.3
• /
• pp.47-54
• /
• 2014

This is a research on the method of how to improve stall characteristics for the small general aviation airplanes to meet the FAR part 23 requirements. This research is based on the experience of certification flight tests of KC-100 airplane for Korea type certification. KAS/FAR Part 23.201/203 are the stall characteristics requirements. 23.201 requires to show the stable stalling tendency of the wings level stall and 23.203 requires to show the stable stalling tendency of stall characteristics during turning flight. In this paper, the stall characteristics requirements, improvement methods and flight test experience of KC-100 airplane for type certification.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.27 no.4
• /
• pp.73-82
• /
• 2019

In order to achieve successful flight training results, various studies on pilot aptitude have been conducted. In this study, we examined the aptitude for the pilots using the teacher aptitude test tool. As a result, the student pilots showed a high aptitude score suitable for conducting aviation training, and the A-type personality type was overwhelmingly large. The study satisfaction of student pilots was classified into educational contents, educational methods, educational environment and facilities, and flight instructors using the questionnaire related to the satisfaction of learning. As a result, the satisfaction of flight instructor among four factors was found to be a major factor in improving flight performance.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.499-505
• /
• 2004

A Propulsion System of the CRW(Canard Rotor Wing) type UAV(Unmanned Aerial Vehicle) was composed of the turbojet engine to generate the propulsive exhaust gas, and the duct system including straight bent ducts, tip-jet nozzles, a master valve and a variable main nozzle for three flight modes such as lift/landing mode, low speed transition flight mode and high speed forward flight mode. In this study, in order to operate safely the propulsion system, the dynamic Performance behavior of the system was modeled and simulated using the SIMULIN $K^{ }$, which is the user-friendly GUI type dynamic analysis tool provided by MATLA $B^{ }$. In the transient performance model, the inter-component volume model was used. The performance analysis using the developed models was performed at various flight condition, valve angle positions and fuel flow schedules, and these results could set the safe flight mode transition region to satisfy the inlet temperature overshoot limitation as well as the compressor surge margin. Performance analysis results using the SIMULIN $K^{ }$ performance program were compared with them using the commercial program GSP.m GSP.

• Journal of Aerospace System Engineering
• /
• v.5 no.1
• /
• pp.30-35
• /
• 2011

Certification flight test is very risky and there are many hazards. Because the flight test is performed with the aircraft, that is safety and flight characteristics are not proven. And the test items and conditions are critical. If there is loss of aircraft during certification flight test, the certification program, development period can be delayed. Therefore, maintaining safety of the aircraft during flight test is very important. There are not much flight test experiences in Korea. However, developed nations has long history of flight test and experiences of flight test accidents. Based on these experiences, they has developed systematic management methods for the flight test safety. In this study, I would like to introduce safety management and risk assessment of the certification flight test.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2560-2565
• /
• 2003

The paper presented here covers the work associated with the flight control law design, ground based and in flight simulation and handling qualities assessment of the Fly-by-Wire type Aircraft (FBWA). The control law was designed for the most unstable aircraft configuration flight regime for the target aircraft (FBWA). The ground based simulation including math-model, real-time pilot-in-the-loop and iron bird simulation were used for validation of the control law before the experimental in-flight simulation on the IFS (In.Flight-Simulator) aircraft. The flight tests results showed that Level 1 handling qualities for the most unstable flight regime were achieved.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.3
• /
• pp.268-276
• /
• 2013

The objective of this paper is to give a general understanding for the development flight test of Korean Utility Helicopter(KUH). This paper contains the contents of detailed flight test plan, the type of flight test, an introduction to main flight test area, and the overview of flight test results. At the beginning, more than 8,500 test points were identified for airworthiness certification to show the compliance for the KUH development requirements. However, the number of flight test points were optimized to 7,800 at the end. To accomplish the test objectives, about 860 flight test sorties had been performed, and more than 1,000 test sorties were consumed for trouble shooting. This paper also describes some major issues faced during development flight test phase.

• Journal of Aerospace System Engineering
• /
• v.14 no.2
• /
• pp.12-19
• /
• 2020

In Korea, the regulation is MOLIT Notice 2018-290, Guidance for Approval of Synthetic Flight Trainer as Flight Simulator and Flight Training Device. The FAA (Federal Aviation Administration) categorizes FSTD (Flight Simulation Training Device) into FFS (Full Flight Simulator) and FTD (Flight Training Device), according to its level. Additional categories for regulation are airplane and helicopter, depending on the type of aircraft. In this study, the objective tests for the handling quality of the FAA and Korean regulations were compared and analyzed. In QPS (Qualification Performance Standard), related test titles, flight conditions, and tolerance limits were analyzed for the handling quality. Based on this study, recommendations on amendments to the regulation was presented.

• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.1
• /
• pp.115-121
• /
• 2007

The aeroelastic analysis of rotor blades with trailing edge flaps, focused on reducing vibration while minimizing control effort, are investigated using large deflection-type beam theory in forward flight. The rotor blade aerodynamic forces are calculated using two-dimensional quasi-steady strip theory. For the analysis of forward flight, the nonlinear periodic blade steady response is obtained by integrating the full finite element equation in time through a coupled trim procedure with a vehicle trim. The objective function, which includes vibratory hub loads and active flap control inputs, is minimized by an optimal control process. Numerical simulations are performed for the steady-state forward flight of various advance ratios. Also, numerical results of the steady blade and flap deflections, and the vibratory hub loads are presented for various advance ratios and are compared with the previously published analysis results obtained from modal analysis based on a moderate deflection-type beam theory.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1441-1445
• /
• 2008

Insect flight is adapted to cope with each circumstance by controlling a variety of the parameters of wing motion in nature. Many researchers have struggled to solve the fundamental concept of insect flight, but it has not been solved yet clearly. In this study, to find the most effective flapping wing kinematics, we conducted to analyze CFD data on fixing some of the optimal parameters of wing motion such as stoke amplitude, flip duration and wing rotation type and then controlled the deviation angle by fabricating wing tip motion. Although all patterns have the similar value of lift coefficient and drag coefficient, pattern A(pear-shape type) indicates the highest lift coefficient and pattern H(pear-shape type) has the lowest lift coefficient among four wing tip motions and three deviation angles. This result suggest that the lift and drag coefficient depends on the angle of attack and the deviation angle combined, and it could be explained by delayed stall effect.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.5 no.1
• /
• pp.17-30
• /
• 1997

FIight Test procedures are studied from FAR 23, AC 23-8, and Order 8110.7. We have been studied the main procedures for the type certification of light airplane from the experiences of Chang Gong 91. This study is intended as a reference for small airplane manufacturers, engineers, flight test engineers, and engineering flight test pilots, including government personnel. This study covers flight test items of interest during type certification. These methods and procedures are promulgated, in the interest of standardization, for use during normal category airplane flight test certification activities.