• 항공우주시스템공학회지
• /
• 제8권3호
• /
• pp.47-54
• /
• 2014

This is a research on the method of how to improve stall characteristics for the small general aviation airplanes to meet the FAR part 23 requirements. This research is based on the experience of certification flight tests of KC-100 airplane for Korea type certification. KAS/FAR Part 23.201/203 are the stall characteristics requirements. 23.201 requires to show the stable stalling tendency of the wings level stall and 23.203 requires to show the stable stalling tendency of stall characteristics during turning flight. In this paper, the stall characteristics requirements, improvement methods and flight test experience of KC-100 airplane for type certification.

• 한국항공운항학회지
• /
• 제27권4호
• /
• pp.73-82
• /
• 2019

In order to achieve successful flight training results, various studies on pilot aptitude have been conducted. In this study, we examined the aptitude for the pilots using the teacher aptitude test tool. As a result, the student pilots showed a high aptitude score suitable for conducting aviation training, and the A-type personality type was overwhelmingly large. The study satisfaction of student pilots was classified into educational contents, educational methods, educational environment and facilities, and flight instructors using the questionnaire related to the satisfaction of learning. As a result, the satisfaction of flight instructor among four factors was found to be a major factor in improving flight performance.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.499-505
• /
• 2004

A Propulsion System of the CRW(Canard Rotor Wing) type UAV(Unmanned Aerial Vehicle) was composed of the turbojet engine to generate the propulsive exhaust gas, and the duct system including straight bent ducts, tip-jet nozzles, a master valve and a variable main nozzle for three flight modes such as lift/landing mode, low speed transition flight mode and high speed forward flight mode. In this study, in order to operate safely the propulsion system, the dynamic Performance behavior of the system was modeled and simulated using the SIMULIN $K^{ }$, which is the user-friendly GUI type dynamic analysis tool provided by MATLA $B^{ }$. In the transient performance model, the inter-component volume model was used. The performance analysis using the developed models was performed at various flight condition, valve angle positions and fuel flow schedules, and these results could set the safe flight mode transition region to satisfy the inlet temperature overshoot limitation as well as the compressor surge margin. Performance analysis results using the SIMULIN $K^{ }$ performance program were compared with them using the commercial program GSP.m GSP.

• 항공우주시스템공학회지
• /
• 제5권1호
• /
• pp.30-35
• /
• 2011

Certification flight test is very risky and there are many hazards. Because the flight test is performed with the aircraft, that is safety and flight characteristics are not proven. And the test items and conditions are critical. If there is loss of aircraft during certification flight test, the certification program, development period can be delayed. Therefore, maintaining safety of the aircraft during flight test is very important. There are not much flight test experiences in Korea. However, developed nations has long history of flight test and experiences of flight test accidents. Based on these experiences, they has developed systematic management methods for the flight test safety. In this study, I would like to introduce safety management and risk assessment of the certification flight test.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2560-2565
• /
• 2003

The paper presented here covers the work associated with the flight control law design, ground based and in flight simulation and handling qualities assessment of the Fly-by-Wire type Aircraft (FBWA). The control law was designed for the most unstable aircraft configuration flight regime for the target aircraft (FBWA). The ground based simulation including math-model, real-time pilot-in-the-loop and iron bird simulation were used for validation of the control law before the experimental in-flight simulation on the IFS (In.Flight-Simulator) aircraft. The flight tests results showed that Level 1 handling qualities for the most unstable flight regime were achieved.

• 한국군사과학기술학회지
• /
• 제16권3호
• /
• pp.268-276
• /
• 2013

The objective of this paper is to give a general understanding for the development flight test of Korean Utility Helicopter(KUH). This paper contains the contents of detailed flight test plan, the type of flight test, an introduction to main flight test area, and the overview of flight test results. At the beginning, more than 8,500 test points were identified for airworthiness certification to show the compliance for the KUH development requirements. However, the number of flight test points were optimized to 7,800 at the end. To accomplish the test objectives, about 860 flight test sorties had been performed, and more than 1,000 test sorties were consumed for trouble shooting. This paper also describes some major issues faced during development flight test phase.

• 항공우주시스템공학회지
• /
• 제14권2호
• /
• pp.12-19
• /
• 2020

In Korea, the regulation is MOLIT Notice 2018-290, Guidance for Approval of Synthetic Flight Trainer as Flight Simulator and Flight Training Device. The FAA (Federal Aviation Administration) categorizes FSTD (Flight Simulation Training Device) into FFS (Full Flight Simulator) and FTD (Flight Training Device), according to its level. Additional categories for regulation are airplane and helicopter, depending on the type of aircraft. In this study, the objective tests for the handling quality of the FAA and Korean regulations were compared and analyzed. In QPS (Qualification Performance Standard), related test titles, flight conditions, and tolerance limits were analyzed for the handling quality. Based on this study, recommendations on amendments to the regulation was presented.

• International Journal of Aeronautical and Space Sciences
• /
• 제8권1호
• /
• pp.115-121
• /
• 2007

The aeroelastic analysis of rotor blades with trailing edge flaps, focused on reducing vibration while minimizing control effort, are investigated using large deflection-type beam theory in forward flight. The rotor blade aerodynamic forces are calculated using two-dimensional quasi-steady strip theory. For the analysis of forward flight, the nonlinear periodic blade steady response is obtained by integrating the full finite element equation in time through a coupled trim procedure with a vehicle trim. The objective function, which includes vibratory hub loads and active flap control inputs, is minimized by an optimal control process. Numerical simulations are performed for the steady-state forward flight of various advance ratios. Also, numerical results of the steady blade and flap deflections, and the vibratory hub loads are presented for various advance ratios and are compared with the previously published analysis results obtained from modal analysis based on a moderate deflection-type beam theory.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1441-1445
• /
• 2008

Insect flight is adapted to cope with each circumstance by controlling a variety of the parameters of wing motion in nature. Many researchers have struggled to solve the fundamental concept of insect flight, but it has not been solved yet clearly. In this study, to find the most effective flapping wing kinematics, we conducted to analyze CFD data on fixing some of the optimal parameters of wing motion such as stoke amplitude, flip duration and wing rotation type and then controlled the deviation angle by fabricating wing tip motion. Although all patterns have the similar value of lift coefficient and drag coefficient, pattern A(pear-shape type) indicates the highest lift coefficient and pattern H(pear-shape type) has the lowest lift coefficient among four wing tip motions and three deviation angles. This result suggest that the lift and drag coefficient depends on the angle of attack and the deviation angle combined, and it could be explained by delayed stall effect.

• 한국항공운항학회지
• /
• 제5권1호
• /
• pp.17-30
• /
• 1997

FAR 23, AC 23-8, 그리고 Order 8110.7을 이용하여 경비행기의 비행 시험 절차에 대한 연구를 수행하였다. 본 연구에서는 창공-91의 비행 시험을 통한 경험을 바탕으로 형식증명을 위한 주요 절차에 대한 연구를 수행하였다. 본 연구는 소형 비행기의 제작자, 항공관련 기술자, 비행 시험 기술자, 비행 시험 조종사, 그리고 관련 정부 관계자들에게 비행 시험에 관련된 기준을 이해하도록 하기 위해 수행된 연구이다. 본 연구에서 비행 시험 방법과 절차는 주로 소형 비행기의 형식증명에 관련된 것으로 관련자들에게 큰 도움이 될 것이다.