• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.610-613
• /
• 1995

In addition to propulsive force to a flying vehicle, a rocket propulsion system can provide moments ro rotatate the flying vehicle and thus provide control of the vehicle's attitude and flight path. By controlling the direction of the thrust vectors, it is possible to control a vehicle's pitch, yaw, and roll motions. In this paper, we will introduce general thrust vector control mechanisms.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.566-568
• /
• 1999

HILS is widely used in the test and evaluation of complex control system. This paper describes the structure of HILS and the control loop performance monitoring of HILS system Distal path delay and FMS(Flight Motion Simulator) dynamics were estimated and output of the estimated model were compared with real FMS output. The monitoring system can be used for analyzing the result of HILS.

• 제어로봇시스템학회:학술대회논문집
• /
• 1995.10a
• /
• pp.376-379
• /
• 1995

To force an aircraft to track the specified path, the generation of the smooth desired trajectory is essential. In this paper, the cubic spline function is used to generate the trajectory which passes through the specified intercept points. The simulation results show that the desired trajectory generated by the spline interpolation is very smooth and the aircraft tracks it with small position errors.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.3
• /
• pp.228-235
• /
• 2010

This paper deals with an autonomous flight controller design problem for a tilt-rotor aircraft in rotary-wing mode. The inner-loop algorithm is designed using the output-based approximate feedback linearization. The model error originated from the feedback linearization is cancelled within allowable tolerance by using single-hidden-layer neural network. According to Lyapunov direct stability theory, the adaptive update law is derived to run the neural network on-line, which is based on the linear observer dynamics. Moreover, the outer-loop algorithm is designed to track the trajectory generated from way-point guidance. Especially, heading and flight-path angle line-of-sight guidance are applied to the outer-loop to improve accuracy of the landing tracking performance. The 6-DOF nonlinear simulation shows that the overall performance of the flight control algorithm is satisfactory even though the collective input response shows instantaneous actuator saturation for a short time due to the lack of the neural network and the saturation protection logic in that loop.

• Journal of Aerospace System Engineering
• /
• v.17 no.1
• /
• pp.68-78
• /
• 2023

In this paper, improvement measures were studied for false alarm (abnormal lighting) of emergency hydraulic warning light due to RF radiation signals in aircraft. When the warning lamp of the emergency hydraulic system is lit during flight due to electromagnetic interference caused by RF radiation signals, it affects flight mission and safety which can result in efficiency degradation and maintenance of flight mission. For false alarm of emergency hydraulic warning light, root cause analysis and troubleshooting were carried out. By shielding a composite strip under fuselage of the aircraft located in the path of the RF radiation signal, the RF radiation signal flowing into the emergency hydraulic indicator was blocked. Results of applying the improvement method through ground and flight monitoring were also described.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1753-1756
• /
• 2005

The sheet parts are formed with dies conventionally. But this conventional forming process is not suited to small volume and varied production for the reason of high cost. For the solution of this problem, a new forming process, which is called CNC incremental sheet forming, is being introduced. This process can form sheet parts without die, and is very well suited to small volume and varied production in space flight and automobile. In this paper, dieless CNC forming system based on a machining center is developed. A special device to grasp and pull the blank sheet built in the machining center and tool path generation S/W from STL file of 3-D model are developed. Several sheet parts are incrementally formed to verify the effectiveness of the developed system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.1
• /
• pp.74-80
• /
• 2006

This paper addresses the trajectory optimization of Unmanned Aerial Vehicles(UAVs) under multiple ground threats like enemy's anti-air radar sites. The power of radar signal reflected by the vehicle and the flight time are considered in the performance cost to be minimized. The bank angle is regarded as control input for a 1st-order lag vehicle, and input parameter optimization method based on Sequential Quadratic Programming (SQP) is used for trajectory optimization. The proposed path planning method provides more practical trajectories with enhanced survivability than those of Voronoi diagram method.

• International journal of advanced smart convergence
• /
• v.12 no.4
• /
• pp.8-19
• /
• 2023

This paper presents advancement in multi- unmanned aerial vehicle (UAV) cooperative area surveillance, focusing on optimizing UAV route planning through the application of genetic algorithms. Addressing the complexities of comprehensive coverage, two real-time dynamic path planning methods are introduced, leveraging genetic algorithms to enhance surveillance efficiency while accounting for flight constraints. These methodologies adapt multi-UAV routes by encoding turning angles and employing coverage-driven fitness functions, facilitating real-time monitoring optimization. The paper introduces a novel path planning model for scenarios where UAVs navigate collaboratively without predetermined destinations during regional surveillance. Empirical evaluations confirm the effectiveness of the proposed methods, showcasing improved coverage and heightened efficiency in multi-UAV path planning. Furthermore, we introduce innovative optimization strategies, (Foresightedness and Multi-step) offering distinct trade-offs between solution quality and computational time. This research contributes innovative solutions to the intricate challenges of cooperative area surveillance, showcasing the transformative potential of genetic algorithms in multi-UAV technology. By enabling smarter route planning, these methods underscore the feasibility of more efficient, adaptable, and intelligent cooperative surveillance missions.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.1
• /
• pp.11-19
• /
• 2015

Objective : The purpose of this study was to analyze the correlation between physical factors (X-factor, X-factor stretch) and club factors (club speed, ball speed, club path, smash factor, vertical launch angle, spin rate, flight time, total length) during impact and it affect on the total distance of the ball during a golf driver swing. Background : There were not enough studies that analyzed the correlation between physical factors(X-factor, X-factor stretch) and club factors(club speed, ball speed, club path, smash factor, launch angle, spin rate, flight time, total length) during a purpose swing to increase total distance. Method : For this study, 9 right handed professional male golfers (KPGA) were chosen. The test subject group used their own drivers and each took a total of 10 swings. These swings consisted of 5 purpose swings to increase total distance and 5 normal swings. Results : The purpose swing to increase total distance showed larger physical factors(X-factor, X-factor stretch) compared to a normal swing however the results were not statistically significant. Total distance increased during a purpose swing as a result of ball and club speed. Conclusion : The results showed that club factors, ball speed and club speed contributed the most in affecting the total distance of the ball during a purpose swing.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.820-824
• /
• 2010

The purpose of this study is to develop basic technology of hybrid rocket vehicle by constructed and launched. This small hybrid rocket using HDPE/LN2O and Aluminium steel for its body (weight : 12.5 kg, diameter : 114 mm, height : 1.8 m) was designed. The fuel grain and injector were designed for 50 kgf thrust and burning time 2.5 sec. This rocket was loaded the data acquisition device for obtaining data of pressure and velocity during its flying and equiped an automatic ejector system using spring/motor and timer to collect the rocket more safely after launching. It was launched successfully, but found some problem that the rocket's weight was heavier than expected and the thrust was not enough to reach the designed altitude and analyzed its flight path way.