• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.3
• /
• pp.246-253
• /
• 2005

An experimenal study on flight control of high-speed AEV(Aero-levitation Electric Vehicle) scale model in wind-tunnel is conducted. The AEV is to fly at very low altitude in predesigned track so that it is always under the wing-in-ground effect. The experiment is intended to fly the scale model to follow the predesigned altitude schedule while holding its attitude (pitch, roll, and yaw). Especially, the altitude changes for climb, cruise, and descent with constant pitch angle are most important maneuvers. The experiment shows that the required mission flights can be performed with appropriate sensors, processors, and actuators.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.6
• /
• pp.468-477
• /
• 2014

In this research, how a solar powered HALE (high altitude long endurance) UAV (Unmanned Aerial Vehicle) can climb and reach mission altitude, 18km, starting from the ground using only solar energy. A glider type aircraft was assumed as a baseline configuration which has wing area of $35.98m^2$ and aspect ratio of 25. Configuration parameters, lift and drag coefficients were calculated using OpenVSP and XFLR5 that are NASA open source programs, and climb flights were predicted through energy balance between available energy from solar power and energy necessary for a climb flight. Minimum time climb flight was obtained by minimizing flight velocities at each altitude and total time and total energy consumption to reach the mission altitude were predicted for different take off time. Also, aircraft moving distances due to westerly wind and flight speed were calculated.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.4
• /
• pp.223-233
• /
• 2018

In this study was classified the cadastral control points and parcel boundary points into 40m, 100m by flight altitude of UAV (Unmanned Aerial Vehicle) which compared the coordinates extracted from the orthophoto with the parcel boundary point coordinates by GNSS (Global Navigation Satellite System) ground survey. As a results of this study, first, in the spatial resolution analysis that the average error of the orthoimage by flight altitude were 0.024m at 40m, and 0.034m at 100m which were higher 40m than 100m for spatial resolution of orthophotos and position accuracy. Second, in order to analyze the accuracy of image recognition by airmark of flight altitude that was divided into three cases of nothing, green, and red of RMSE (Root Mean Square Error) were X=0.039m, Y=0.019m and Z=0.055m, the highest accuracy. Third, the result of the comparison between orthophotos and field survey results that showed the total RMSE error of the cadastral control points were X=0.029m, Y=0.028m, H=0.051m, and the parcel boundary points were X=0.041m, Y=0.030m. In conclusion, based on the results of this study, it is expected that if the average error of flight altitude is limited to less than 0.05m in the legal regulations related to orthophotos for cadastral surveying, it will be an economical and efficient method for cadastral survey as well as spatial information acquisition.

• Journal of Astronomy and Space Sciences
• /
• v.36 no.3
• /
• pp.213-223
• /
• 2019

This paper analyzes delta-Vs to maintain an extremely low altitude on the Moon and investigates the possibilities of performing a CubeSat mission. To formulate the station-keeping (SK) problem at an extremely low altitude, current work has utilized real-flight performance proven software, the Systems Tool Kit Astrogator by Analytical Graphics Inc. With a high-fidelity force model, properties of SK maneuver delta-Vs to maintain an extremely low altitude are successfully derived with respect to different sets of reference orbits; of different altitudes as well as deadband limits. The effect of the degree and order selection of lunar gravitational harmonics on the overall SK maneuver strategy is also analyzed. Based on the derived SK maneuver delta-V costs, the possibilities of performing a CubeSat mission are analyzed with the expected mission lifetime by applying the current flight-proven miniaturized propulsion system performances. Moreover, the lunar surface coverage as well as the orbital characteristics of a candidate reference orbit are discussed. As a result, it is concluded that an approximately 15-kg class CubeSat could maintain an orbit (30-50 km reference altitude having ${\pm}10km$ deadband limits) around the Moon for 1-6 months and provide almost full coverage of the lunar surface.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.1
• /
• pp.120-131
• /
• 2016

The full results of troubleshooting process related to the flight control system of a tilt-rotor type UAV in the flight tests are described. Flight tests were conducted in helicopter, conversion, and airplane modes. The vehicle was flown using automatic functions, which include speed-hold, altitude-hold, heading-hold, guidance modes, as well as automatic take-off and landing. Many unexpected problems occurred during the envelope expansion tests which were mostly under those automatic functions. The anomalies in helicopter mode include vortex ring state (VRS), long delay in the automatic take-off, and the initial overshoot in the automatic landing. In contrast, the anomalies in conversion mode are untrimmed AOS oscillation and the calibration errors of the air data sensors. The problems of low damping in rotor speed and roll rate responses are found in airplane mode. Once all of the known problems had been solved, the vehicle in airplane mode gradually reached the maximum design speed of 440km/h at the operation altitude of 3km. This paper also presents a comprehensive detailing of the control systems of the tilt-rotor unmanned air vehicle (UAV).

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.10
• /
• pp.1012-1019
• /
• 2010

In this paper, The flight data processing system was designed for multiple target flight test. For flight data processing, multiple target grouping, data fusion processing, and data slaving processing were performed and, as a data fusion filter, centralized, and federated Kalman filters were designed. A centralized kalman filter was modified in order to improve the vehicle's low altitude measurement using radar's SNR and estimation process. From the testing of multiple target missile, it confirmed flight trajectory measurement was improved in low altitude area and the beginning stage of vehicle.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.9
• /
• pp.867-873
• /
• 2008

Model based virtual Flight Control System construction is essential for Fly-by-Wire Flight Control System verification & validation(V&V) of concurrent engineering base. We researched the concept of dual-architecture system for virtual system construction, and analyzed Flight Control System that is applied to high altitude long endurance(HAE) UAS. Finally, we constructed the model based virtual Flight Control System with system analysis and achieved system verification about flight critical failure modes. Analysis target is RQ-4A.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.3
• /
• pp.38-44
• /
• 2003

In this study, a performance model of the smart UAV propulsion system with ducts, tip jets and variable main nozzle, which has flight capability of the rotary wing mode for the take-off/landing and low speed forward flight as well as the fixed wing mode for high speed forward flight, has been newly developed With the proposed model, steady-state performance analysis was performed at various flight modes such as rotary wing mode, fixed wing mode, compound ing mode and altitude as well as at flight speed conditions. In investigation of performance analysis. it was noted that the operational capability of the propulsion system was limited due to the duct losses depending on each flight mode, and the limitation with the altitude variation case had much greater than that with the flight speed variation case.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.177-182
• /
• 2003

In this study, a performance model of the Smart UAV propulsion system with ducts, tip jets and variable main nozzle, which has flight capability of the rotary wing mode for the take-off/landing and low speed forward flight as welt as the fixed wing mode for high speed forward flight, has been newly developed. With the proposed model, steady-state performance analysis was performed at various flight modes and conditions, such as rotary wing mode, fixed wing mode, compound wing, mode altitude and flight speed. In investigation of performance analysis, it was noted that the operational capability of the propulsion system was limited due to the duct losses depending on each flight mode, and the limitation with the altitude variation case has much greater than that with the flight speed variation case.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.2
• /
• pp.58-63
• /
• 2011

A Continuous Descent Approach(CDA) is defined as a simple, cost-effective, noise and emission abatement technique for any powered aircraft on approach. CDA also can be optimised within energy, speed and safety constraints by avoiding unnecessary flap, air brake and engine thrust. This study includes comparison on fuel consumption between Continuous Descent type and Step Down type by using flight data. In particular, we investigated fuel flow per hour, calibrated airspeed and pressure altitude for all flight time. During descent flight, the fuel consumption of Continuous Descent type was less than the fuel consumption of Step Down type.