• Advances in concrete construction
• /
• 제11권1호
• /
• pp.45-58
• /
• 2021

Experimental investigation has been conducted to study the effect of using Micro/Nano Silica in presence of steel fibers on improving the static response of reinforced concrete beams. Twenty-one mixtures were prepared with micro silica (MS), Nano silica (NS) and steel fibers (SFs) at different percentages. Cement was replaced by 10% and 15% of Micro silica and 1%, 2% and 3% of Nano silica in the presence of steel fibers at different volume fractions 0%, 1%, and 2%. 258 concrete samples, (126 cubes, 63 cylinders, 63 prisms, and six R.C beams), were investigated experimentally in two stages. The first stage was to investigate the mechanical properties of the prepared mixtures. The second stage was to study the static behavior of R.C beams, using the designed concrete mixtures, under a four-point flexural test. The results showed that replacing cement by (10% MS and 1% NS) produces the optimum mix with a significant improvement in the mechanical properties and the response of R.C beams under static loads. In addition, incorporating steel fibers at different volume fractions have a considerable effect on the flexural toughness of concrete mixes.

• 연구논문집
• /
• 통권23호
• /
• pp.165-171
• /
• 1993

$Si_3N_4/Sic$. nano-composites were fabricated by hot-pressing, gas pressure sintering. The composites contained up to 50 wt. % of SiC. The mechanical properties such as strength, toughness, and hardness of the composite are compared each other. The flexural strength of the composites was improved significantly by introducing fine SiC particles into $Si_3N_4$ matrix, while the fracture toughness was not improved. The increase in flexural strength is attributed to the formation of uniformly elongated $\beta -Si_3N_4$ grains as well as the reduction of grain size.

• 한국세라믹학회지
• /
• 제33권1호
• /
• pp.101-109
• /
• 1996

The mechanical propertieso f sintered AlN with the addition of alumina were investigated The flexural strength of the AlN dispersed ALON specimens was higher than that of ALON and fracture toughness showed similar tendency. The high-temperature flexural strength of specimens which 50 and 64.3 mol% alumina was added to AlN was constant up to 100$0^{\circ}C$ with about 290 and 420 MPa respectively but abruptly decreased at 120$0^{\circ}C$ In the specimens which contained 5 and 30mol% alumina the flexural strength increased to about 14% at 100$0^{\circ}C$ and did not decrease at 120$0^{\circ}C$ compared to at room temperature.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.673-676
• /
• 2006

Steel FibreReinforced Shotcrete(SFRS) is one of the main tunnel support along with the rock bolt during the excavation and after the completion of the tunnel. In the standard qualification of the SFRS defined by Korea Highway Corporation, 28 day core specimen has to meet the compressive strength of 19.6 MPa and over 90 % fibre contents. Furthermore, for the 28 days brick shaped specimen made by shooting, flexural strength should be over 4.4 MPa and flexural toughness ratio which can be calculated from flexural toughness factor has to meet more than 68% of flexural strength. In shotcrete, accelerating agent is added for the rapid strength development. Silicate and aluminate type agents are known to develop shotcrete strength rapidly, however, has such problem to degrade the middle and long term strength. Hence, using poly carboxylic super plasticizer, it was aimed to enhance the quality of the shotcrete with the lower water-cement ratio and the same level of workability. The present paper shows the part of the field test result and its analysis.

• 콘크리트학회지
• /
• 제6권1호
• /
• pp.131-141
• /
• 1994

본 실험적 연구는 강섬유의 길이와 혼입율이 콘크리트의 파괴인성과 강도에 미치는 영향을 고찰하기 위하여 수행되었다. 강섬유의 길이(30,60mm)와 혼입율(0.0, 0.5, 1.0, 1.5, 2.0%)을 달리한 노치를 가진 강섬유보강콘크리트 보를 제작하여 3점 휨시험을 하였으며, 그 실험결과로부터 파괴에너지, CMOD 및 휨강도 등을 구하였다. 또한 파괴에너지로부터 콘크리트의 파괴인성을 평가하였다. 연구결과, 콘크리트의 파괴인성과 강도는 전반적으로 강섬유의 혼입율이 증가할수록 증가하였으며 강섬유의 길이는 휨강도에는 큰 영향을 주었으나 파괴인성과 압축강도에는 거의 영향을 주지않았다. 또한 강섬유의 분산성, 시공연도 및 굵은골재의 최대치수 등을 고려할 때, 콘크리트의 파괴인성과 강도측면에서 강섬유의 혼입율은 1.0%정도가 최적이라 판단되며, 그길이가 긴 경우 약간 유리하였다.

• 한국건설순환자원학회논문집
• /
• 제4권4호
• /
• pp.470-476
• /
• 2016

Many studies have been performed on hybrid fiber reinforced concrete for years, which is to improve some of the weak material properties of concrete. Studies on characteristics of hybrid fiber reinforced concrete using amorphous steel fiber and polyamide fiber, however, yet remain to be done. The purpose of this experimental research is to evaluate the workability and mechanical properties of hybrid fiber reinforced concrete using amorphous steel fiber and polyamide fiber. For this purpose, the hybrid fiber reinforced concrete containing amorphous steel fiber(ASF) and polyamide fiber(PAF) were made according to their total volume fraction of 0.5 % for water-binder ratio of 33 %, and then the mechanical properties such as the compressive strength, direct tensile strength, flexural strength, and flexural toughness of those were estimated. It was observed from the test results that the compressive strength was slightly decreased with increasing ASF and decreasing PAF and the effect of fiber combination on the flexural strength was not much but the flexural toughness was relatively largely increased with decreasing ASF and increasing PAF.

• 한국지반공학회논문집
• /
• 제29권6호
• /
• pp.53-62
• /
• 2013

NATM공법을 이용한 터널 시공에서 초기에 원지반을 구속시키고 암반과의 일체화를 통해 터널의 안정성을 확보하기 위해 통상 5-20cm 두께의 숏크리트를 시공하며 여기에는 강섬유가 $40kg/m^3$ 정도 포함되도록 설계하고 있다. 숏크리트 내에 혼합된 강섬유는 숏크리트를 뿜어 내는 장비 특성, 혼합비 그리고 현장 암반 상태에 따라 숏크리트 내 강섬유가 골고루 분산될 수도 있고 그렇지 않을 수도 있다. 본 연구에서는 단면이 $15cm{\times}15cm$이고 길이 55cm인 사각기둥 모양의 시멘트 혼합비가 5% 또는 20%인 공시체를 3cm씩 다섯 층으로 나누어 강섬유를 혼합하지 않거나, 중간층만 혼합하거나, 1, 3, 5층만 혼합하거나, 전층을 혼합한 네 종류의 숏크리트를 모사한 콘크리트 공시체를 제작하였다. 7일 동안 공시체를 대기중 양생한 다음 휨강도시험을 실시하여 층별로 강섬유가 분산되거나 집중될 경우 휨강도와 인성에 미치는 영향에 대하여 연구하였다. 시멘트 혼합비가 20%인 경우 강섬유 혼합층이 증가할수록 휨강도는 증가하였으며, 동일한 양의 강섬유가 골고루 분산되지 않고 한 곳으로 집중될 경우 휨강도가 20% 정도 감소하였다. 한편 시멘트 혼합비가 5%로 낮은 경우에는 강섬유 혼합층이 증가할수록 오히려 휨강도는 감소하였다. 시멘트 혼합비에 관계없이 강섬유 혼합층이 증가할수록 인성지수는 점점 증가하는 경향을 보였으며, 강섬유가 중간층으로 집중된 경우보다 골고루 분산된 경우 인성지수는 2-3배 정도 증가하였다.

• 한국지반신소재학회논문집
• /
• 제16권1호
• /
• pp.19-29
• /
• 2017

시멘트-점토-모래 혼합토의 휨성능 개선을 위하여 합성섬유를 이용해서 보강한 섬유보강토에 대한 휨성능 시험을 실시하였다. 시멘트, 모래, 그리고 섬유가 혼합토의 휨성능에 미치는 영향을 평가하기 위하여 시멘트량(15%, 20%, 25%), 모래함량(0%, 10%, 20%), 섬유의 종류(PP, PVA)와 길이(6mm, 12mm), 섬유혼입량(0.5%, 1.0%, 1.5%)을 조합하여 시험편을 제작하였다. 본 연구의 결과 시멘트 개량토를 섬유를 이용해서 보강하면 휨강도와 휨인성이 개선되는 효과를 확인할 수 있었다. 휨성능 시험 결과에 대한 다중선형회귀분석 결과 시멘트량과 모래함량은 휨강도에 영향을 미치는 주요 인자인 것으로 나타났고, 반면에 섬유혼입량은 균열발생 후의 거동에 영향을 미치는 주요 인자인 것으로 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.380-385
• /
• 1998

Nowadays, shotcrete plays an essential part in he construction of underground structures, and steel fiber is so useful for increasing the toughness of the concrete that is spotlighted at tunnel or pavement site. A variety of tests have been developed to measure and quantity the improvements achievable in steel fiber reinforced concrete(SFRC) and shotcrete. But Korea doesn`t have specific standards in this respect, and the only criteria that KHC(Korea Highway Corporation) applies to tunnel shotcreting are flexural strength and toughness quotient. Test results in order to manage the quality of steel fiber reinforced concrete and shocrete are very affected by various test method. Therefore, this study deals with the test methodological effects on SFRC quality. The major interests are loading method, that is, load control and displacement control, loading velocity, support condition.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.683-688
• /
• 2000

Nowadays, shotcrete plays an essential part in the construction of underground structures, and fiber reinforcement is so useful for increasing the toughness of the concrete that is spotlighted at tunnel or pavement construction. Therefore, many type of fibers have been introduced on the site and variety of tests have been developed to measure and quantify the improvements achievable in fiber reinforced concrete and shotcrete. Therefore, this study focuses on the flexural toughness according to the fiber types and appraisal methods. The major interests are fiber types, volume fractions and evaluation methods.