• Carbon letters
• /
• 제14권3호
• /
• pp.190-192
• /
• 2013

It has been demonstrated in a previous study that carbon nanotube (CNT)/epoxy/basalt composites produce better flexural properties than epoxy/basalt composites. In this study, mode I fracture tests were conducted using CNT/epoxy/basalt composites with and without seawater absorption in order to investigate the effect of the seawater absorption on the mode I fracture toughness ($G_{Ic}$) of the CNT/epoxy/basalt composites. The results demonstrated that the compliance of the seawater-absorbed specimen was larger than that of the dry specimen at the same crack length, while the opposite result was obtained for the fracture load. The $G_{Ic}$ value of the seawater-absorbed CNT/epoxy/basalt composites was approximately 20% lower than that of the dry CNT/epoxy/basalt composites.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.209-217
• /
• 2021

이 논문은 고강도 후크형 강섬유 보강량과 형상비에 따른 콘크리트의 압축 및 휨 성능에 미치는 영향에 대하여 다룬다. 이를 위하여 총 10개 콘크리트 배합이 계획되었다. 설계기준강도 30 MPa인 콘크리트에 형상비(l/d)가 64, 67, 80인 강섬유를 0.25%, 0.50%, 0.75% 혼입하여 강섬유 보강콘크리트가 제조되었다. 형상비 64, 67, 80인 강섬유의 인장강도는 각각 2,000, 2,400, 2,100 MPa이다. 시험 결과로부터 고강도 후크형 강섬유의 혼입량은 콘크리트의 압축 및 휨 성능에 영향을 미치는 것으로 나타났다. 강섬유 혼입량이 증가함에 따라 푸아송비 및 압축인성은 향상되었으나 콘크리트의 압축강도 및 탄성계수에 큰 변화를 보이지 않았다. 강섬유 보강 콘크리트의 균열발생후 휨거동의 특성을 나타내는 잔여 휨강도 및 노치에서 시작된 균열면에서 에너지 소산능력은 강섬유의 혼입률 및 형상비에 따라 크게 좌우되었다. 특히 MC2010에서 정의된 사용 및 극한 상태한계에서의 잔여 휨강도는 강섬유 혼입량과 형상비가 증가함에 따라 증가되었다.

• 한국세라믹학회지
• /
• 제30권12호
• /
• pp.993-998
• /
• 1993

Nicalon-fiber-reinforced SiC composites were fabricated via polymer solution infiltration/chemical vapor infiltration (PSI/CVI) and CVI. Specifically, data were taken and compared for flexural strength, fracture toughness, and processing time. The two process resulted in comparable mechanical properties, and PSI/CVI process resulted in significantly reduced infiltration time.

• 콘크리트학회지
• /
• 제6권6호
• /
• pp.151-158
• /
• 1994

본 연구에서는 수경성 시멘트 경화체의 구조적 결함인 휨강도를 향상시키시 위해 보통 포틀랜드 시멘트비를 0.1로 하여 혼합수량을 줄이고 수용성 고분자 물질인 Hydroxy Propy Methyl Cellulose(HPMC)를 첨가하여 시멘트입자의 윤활작용에 따른 균일한 분산효과와 결합효과를 얻도록 하였으며, twin roll mill로 혼련 성형하여 치밀하고 균일한 경화제 시편을 제조하였다. 이러한 고강도 시멘트 경화체의 휨강도는 약 96MPa, 탄성계수는 60GPa로 우수한 특성을 나타내었다. 고강도 시멘트의 고강도화 기구는 100${\mu}m$ 이상의 큰 기공제거 및 균열성장경로인 모세관 기공의 감소, 미수화 시멘트의 증가로 인한 탄성계수의 증가와 crack toughening(입자 가교, 고분자 섬유 가교, frictional interlocking)에 의한 파괴 인성의 향상 때문인 것으로 판단된다.

• 한국세라믹학회지
• /
• 제34권9호
• /
• pp.915-920
• /
• 1997

Tetragonal ZrO2 polycrystal (TZP), consisted of 90.24 mol% ZrO2-5.31 mol% Y2O3-4.45 mol% Nb2O5, were prepared using hot-press and mechanical properties and high-temperature degradation were investigated. The specimen, hot-pressed for 1 h at 140$0^{\circ}C$ in Ar atmosphere, exhibited flexural strength of 1010 MPa and fracture toughness of 7.5 MPam1/2 and experienced no low-temperature degradation below 40$0^{\circ}C$. However, as aged for 100h at temperatures higher than 40$0^{\circ}C$, TZP was suffered by high-temperature degradation due to an extensive cavitation caused by the oxidation of carbon. XPS observation revealed that the carbon incorporated in TZPs during hot-pressing exists as either an ether-type CO or a carbonyl-type C=O. Despite of the high-temperature degradation of t-ZrO2 co-doped with Y2O3 and Nb2O5, its flexural strength and fracture toughness were superior to those of the commercial 3 mol% Y2O3-TZP hot-pressed under the identical condition as determined before and after the aging treatments.

• 한국세라믹학회지
• /
• 제34권5호
• /
• pp.443-448
• /
• 1997

Titanium carbonitride (Ti(CxN1-x)) ceramics were prepared by hot pressing of the mixture of TiN and graphite. Hot pressing was performed in a graphite mold at 198$0^{\circ}C$ for 40 min under 44 MPa in N2 atmosphere. The effect of graphite addition on sinterability and the mechanical properties of titanium carbonitride were investigated. In this study, the solubility limit of graphite in Ti(CxN1-x) was slightly below 10 wt% based on the results of XRD analysis. Within the solubility limit, graphite dissolved completely into titanium nitride and formed the single phase Ti(CxN1-x) solid solution. Peak relative density of 99% and hardness of 16 GPa were observed for Ti(CxN1-x) ceramics with 7 wt% graphite while maximum flexural strength of 500 MPa and fracture toughness of 4.0 MPa.m1/2 were observed for Ti(CxN1-x) ceramics with 10 wt% graphite. The electrical resistivities of the ceramics with 7 wt% and 10 wt% graphite were observed 40 {{{{ mu OMEGA }}cm and 50 {{{{ mu OMEGA }}cm respectively.

• 한국세라믹학회지
• /
• 제28권2호
• /
• pp.130-140
• /
• 1991

The powders of the system Si3N4-Y2O3-AlN were prepared using Si(OC2H5)4 and YCl3.6H2O together with commercial AlN powder. $\alpha$-Si3N4 was prepared by the carbothermal reduction and nitridation of the hydrolyzed gel at 135$0^{\circ}C$ for 10h in N2 atmosphere. YCl3.6H2O was observed to be changed to Y2O3 during the reaction. $\alpha$-Sialon(X=0.2, 0.4, 0.6) ceramics were obtained by hot-pressing the Si3N4-Y2O3-AlN mixture at 178$0^{\circ}C$ for 1h under 30 MPa. The content of $\alpha$-Sialon increased with increasing metal solubility(x value) and $\alpha$-Sialon single phase was obtained at the metal solubility of 0.6. With increasing metal solubility, flexural strength, fracture toughness and thermal shock resistence were decreased, while the microhardness was increased. Large elongated $\beta$-Si3N4 grains were mainly observed at lower metal solubility. Mechanical prorerties of the sintered ceramics with X=0.2 were measured as follows : flexural strength ; 650 MPa, fracture toughness ; 3.63 MN/m3/2, hardness ; 14.7 GPa, thermal shock resistence temperature ; 58$0^{\circ}C$.

• 한국해양공학회지
• /
• 제23권5호
• /
• pp.32-38
• /
• 2009

Silicon nitride samples with aligned whisker seeds were prepared with different amounts of yttria and alumina as the sintering additives. Their sintering behaviors and the microstructural developments between $1850^{\circ}C$ and $2050^{\circ}C$ were examined. The sample with larger amount of the sintering additives showed faster densification and grain growth. Even though addition of the aligned whisker seeds slightly retarded densification of silicon nitride, it improved the flexural strength and the fracture toughness. Both the flexural strength and the fracture toughness of silicon nitride with the aligned whisker seeds were increased as the amount of the sintering additives was increased.

• 한국도로학회논문집
• /
• 제14권5호
• /
• pp.21-29
• /
• 2012

PURPOSES: This study is to investigate the mechanical performance of the fiber reinforced lean concrete with respect to different types of fibers. METHODS: Increased vehicle weight and other causes from the exposed conditions have accelerated the deteriorations of road pavement. A new multi-functional composite pavement system is being developed recently in order to extend service life and upgrade the pavement. A variety of tests were conducted before and after hardening of the concrete. RESULTS: From the test results, it was found that the use of different types of fibers did not affect the compressive strength development. This might be due to the inherent property of the lean concrete. When steel fibers were used relatively greater flexural strength and flexural fracture toughness were developed. Also addition of fly ash by replacing a part of Portland cement the fracture toughness was slightly increased. CONCLUSIONS: It has been known that the addition of fibers and use of mineral admixture can be positively considered in the development of multi-functional composite pavement system as its required mechanical performance is obtained.

• 한국도로학회논문집
• /
• 제14권6호
• /
• pp.1-11
• /
• 2012

PURPOSES : The purpose of the study was to examine dynamic features of concrete after mixing a little macro fiber with small aspect ratio and long length utilized for bridge, tunnel and shotcrete for tensile performance and crack control in domestic/overseas countries with cement concrete pavement mix. METHODS : Coarse aggregates with small aspect ratio and macro fibers with maximum length of approximately 32 mm are introduced in small quantities in the mix proportions of concrete pavement so as to prevent loss of the workability. Then, this study intends to evaluate the applicability of macro fibers in the mix proportions of concrete pavement by examining the basic construction performance, as well as the change of toughness, the equivalent bending strength and the flexural toughness index caused by compression, bending, tension and the flexural stress-displacement curve. RESULTS : As the results, in each kind of macro fiber, polyvinyl alcohol fiber and steel fiber displayed a good performance. CONCLUSIONS : In 0.2 and 0.3% of fiber contents, it is appeared that polyvinyl alcohol fiber has a large effect on improvement of tensile performance and steel fiber on improvement of deforming performance of bending stress.