• Structural Engineering and Mechanics
• /
• v.56 no.1
• /
• pp.27-47
• /
• 2015

In this study, the accuracy and reliability of fully nonlinear method against equivalent linear method for dynamic analysis of soil-structure interaction is investigated comparing the predicted results of both numerical procedures with the results of experimental shaking table tests. An enhanced numerical soil-structure model has been developed which treats the behaviour of the soil and the structure with equal rigour. The soil-structural model comprises a 15 storey structural model resting on a soft soil inside a laminar soil container. The structural model was analysed under three different conditions: (i) fixed base model performing conventional time history dynamic analysis, (ii) flexible base model (considering full soil-structure interaction) conducting equivalent linear dynamic analysis, and (iii) flexible base model performing fully nonlinear dynamic analysis. The results of the above mentioned three cases in terms of lateral storey deflections and inter-storey drifts are determined and compared with the experimental results of shaking table tests. Comparing the experimental results with the numerical analysis predictions, it is noted that equivalent linear method of dynamic analysis underestimates the inelastic seismic response of mid-rise moment resisting building frames resting on soft soils in comparison to the fully nonlinear dynamic analysis method. Thus, inelastic design procedure, using equivalent linear method, cannot adequately guarantee the structural safety for mid-rise building frames resting on soft soils. However, results obtained from the fully nonlinear method of analysis fit the experimental results reasonably well. Therefore, this method is recommended to be used by practicing engineers.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.1
• /
• pp.99-110
• /
• 2000

The damages due to wave impact loads are largely affected by impact pressure impulse and impact load area. The objective of this study is, as the third step, to perform dynamic structural analysis of bow flare structure of 300,000 DWT VLCC using LS/DYNA3D code, and to verify its dynamic structural behaviors. The impact load areas of stiffener space $1.5s{\times}1.5s$ and $2.5s{\times}2.5s$ are applied to bow flare structure part with relatively flexible stiffeners, and with stiff members such as stringers, webs etc., respectively, under the wave impact load with peak height 6.5MPa, tail 1.0MPa, and duration time 5.0msec. Through the dynamic structural analysis in this study, it might be thought that the structural strength of bow flare structure is generally sufficient for these wave impact load and areas, except that large damages were found at bow flare structure area with flexible wide span stiffeners.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.1
• /
• pp.39-46
• /
• 2013

Smart material such as SMA (Shape Memory Alloy) has been studied in various ways because it can perform continuous, flexible, and complex actuation in simple structure. Smart soft composite (SSC) was developed to achieve large deformation of smart material. In this paper, a shell actuator using woven type SSC was developed to enhance stiffness of the structure while keeping its deformation capacity. The fabricated actuator consisted of a flexible polymer and woven structure which contains SMA wires and glass fibers. The actuator showed various actuation motions by controlling a pattern of applied electricity because the SMA wires are embedded in the structure as fibers. To verify the actuation ability, we measured its maximum end-edge bending angle, twisting angle, and actuating force, which were $103^{\circ}$, $10^{\circ}$, and 0.15 N, respectively.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6A
• /
• pp.641-650
• /
• 2009

This paper presents new equations for member forces in concrete floating structures under wave loadings. The currently adopted design equations for wave loadings disregard the effect of mismatch between design wave length and the length of the structure. In most cases, however, additional internal forces occur due to disequilibriating buoyancy caused by the difference between design wave length and the length of the structure. In this study, new design equations considering the influence of the disequlibriating buoyancy is proposed. In addition, finite element solutions are sought to demonstrate the adequacy of the proposed design formulae in estimating the actual internal forces considering the structure as either rigid or flexible. It has been found that member forces are decreased approximately to around 55% for flexible model when compared with the rigid one.

• Journal of Korean Association for Spatial Structures
• /
• v.13 no.3
• /
• pp.65-72
• /
• 2013

Long span arch structure is composed of arch as relatively flexible structure and column as relatively rigid structure. In this study, the characteristic of dynamic response is analyzed according to the natural frequency ratio between arch and columns. The result of analysis for arch as relatively vertical vibration mode is dominant, the influence of columns mainly appears at relatively high frequency band according to increase of 1st mode frequency in column. However, the dynamic characteristic of arch structure is expected to vary with not only frequency ratio but interaction between vibration modes of arch and columns.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.312-318
• /
• 2001

This paper suggests the finite element method to analyze the dynamic characteristics of a rotating HDD system including the supporting structure with general shape. The flexible supporting structure was modeled by tetrahedra elements to produce a finite element model of disk-spindle-shaft-housing system and the dynamic characteristics of the HDD system was investigated due to the change of rotating speed. The validity of the presented method was verified by the modal testing. The supporting structure has an crucial effect on lower modes for HDD system, so that it is required to consider the supporting structure to accurately analyze the dynamic characteristics of HDD system.

• Journal of the Korean Magnetic Resonance Society
• /
• v.2 no.1
• /
• pp.41-49
• /
• 1998

A linear undecapeptide, Substance P (SP) is involved in a wide variety of physiological processes such as pain, inflammation, salivation, and hypertension. Tertiary structure of SP in dodecylphosphocholine (DPC) micelles has been investigated by CD, NMR spectroscopy, and DGII calculation. CD spectrum of SP in the presence of 7.5 mM DPC micelles does not show any favorable secondary structure. The tertiary structure determined by NMR spectroscopy and DGII calculation shows that the Phe7-Phr8-Gly9-Leu10 region adopts a turn structure, while the N-terminal region is quite flexible. Both prolines in SP exist preferentially as the trans isoforms and the aromatic ring of Phe7 protrudes outward. Conformation of SP may be restrained by the contact of the Phe7 aromatic ring with the hydrophobic side chains of the DPC micelles and this interaction induces a turn structure. Structure of SP in aqueous solution in the presence of DPC micelles can represent a good model to study the conformation recognized by the receptor near neutral membrane.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.29B no.7
• /
• pp.1-10
• /
• 1992

This paper gives on overview of register windowing structure and presents advantages and limitations. Based on these advantages and disadvantages, an original approach for the design of large register file is presented, analyzed and compared with existing approaches. The advantages and disadvantages of this new approach to register file design are discussed, and conditions under which it works better than the existing approaches are outlined. Design tradeoffs are examined in an analytic and empirical study, and the results of which are summarized in the conclusion of this paper.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.127-132
• /
• 2003

Through advance in construction techniques, engineering progress, availability of new materials, and economic considerations, buildings are becoming taller, lighter, and more flexible. In addition, today/s buildings are largely of regular geometric shape with smooth glass metal exteriors, which increase the likelihood of vortex shedding. The wind induced oscillation of the building, if not properly damped, could cause occupant discomfort and other problem. This paper will deal with residual building structure equipped with viscoelastic dampers. And the dampers are installed on the 42th story according to the maximum relative deformation.

• Architectural research
• /
• v.3 no.1
• /
• pp.45-52
• /
• 2001

In this paper, a pressurized single vertical arch and a pressurized leaning arch composed of flexible fabric material are considered. These arches have also been considered as a possible support structure for the tent-like structures. Two different boundary conditions are considered in leaning arches with fixed bases and pinned bases. The behaviors of the leaning arches are investigated for two tilt angles as 15, 30. For each angle, two loading conditions are considered as uniformly distributed load and wind loads. The F.E.M. is used through the all analysis procedures. For the results, load-deflection relationships, buckling modes, differences between two boundary conditions and deformed configurations are discussed.