• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.511-516
• /
• 2000

In order to not only perform as a extreme model under the severe operating condition but also acquire more diverse and advanced control capability utilizing high compliance, active vibration control of a flexible 2-link robot manipulator are investigated. Multi variable-structured frequency shaped optimal sliding mode is proposed for the flexible robot manipulator like control system, whose control variables, an angular motion of joint and vibration of flexible link, have to be controlled simultaneously by one control torque at a driving joint. The control system is divided into two subsystems, a control input related subsystem and an added subsystem. The proposed sliding mode, composed of multi control variables, makes optimized relation between subsystems and a individual control input, thus, the sliding mode controller can compensate whole dynamics of each subsystems simultaneously. And the possibility and effectiveness are verified by vibration control of a manipulator having two flexible links. Simulation and experiment results show that the proposed control scheme achieves the purpose effectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.171-172
• /
• 2008

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.721-724
• /
• 1994

This paper proposes a continuous hitting by a flexible link hammer. This hammer system is used only the first mode of vibration for a desired hitting. The input of the hammer driver for a continuous hitting is obtained from numerical solutions of two sets of non-linear simultaneous equations which satisfy the hitting conditions. Being too complicated, these numerical calculations are not useful for online processing. Therefore, the multi-layered neural networks are applied to the generation of the input patterns of the hammer driver. The trained network outputs agree well to the numerical solutions.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.12
• /
• pp.1045-1052
• /
• 2000

In this paper, we propose a method to apply the Input Shaping Technique (IST) to multi-input multi-output (MIMO) systems. In MIMO systems, there is a high possibility of multi-mode residual vibration. The IST filter designed for this multi mode may need a longer time to suppress the residual vibration. Previous works prove that we can shorten the time lag by using negative sequence. This negative sequence, however, causes another problem - it requires excessive control input. In this paper, we provide a remedy to reduce the size of control input by limiting the reference input by limiting the reference input and its derivative. The result of simulations and experiments on a 2 link flexible arm confirmed the effectiveness of the proposed method.

• Journal of Positioning, Navigation, and Timing
• /
• v.8 no.1
• /
• pp.1-12
• /
• 2019

In this paper, we implement a navigation software of a Global Navigation Satellite System (GNSS) receiver based on a commercial purpose GNSS software receiver platform and verify its performance by performing experimental tests for various GNSS signals available in Korea region. The SX3, employed in this paper, is composed of an application program and a Radio Frequency (RF) frontend, and can capture and process multi-constellation and multi-frequency GNSS signals. All the signal processing procedure of SX3 is accessible by the receiver software designer. In particular for an easy research and development, the Application Programing Interface (API) of the SX3 has a flexible architecture to upgrade or change the existing software program, equipped with a real-time monitoring function to monitor all the API executions. Users can easily apply and experiment with the developed algorithms using a form of Dynamic Link Library (DLL) files. Thus, by utilizing this flexible architecture, the cost and effort to develop a GNSS receiver can be greatly reduced.

• Journal of Aerospace System Engineering
• /
• v.14 no.6
• /
• pp.26-35
• /
• 2020

The national satellite operation network, which supports multiple satellites, was designated as a Critical Information Infrastructure (CII) in 2017. The network was designed independently from the control network and the information network to enhance physical security. Planning is underway to establish a bidirectional data interface between networks. The data transmission system allows data flow only to the physical layer and the data link layer; hence, only one file can be transferred at any one time. This means that when large amounts of data are being transmitted, no other data can be sent simultaneously in urgent situations. Thus, this paper discusses the design of flexible packets for the transmission of data between networks in an environment where physical security has been enhanced through network separation and based on this, presents a method for transmitting data effectively.

• 제어로봇시스템학회:학술대회논문집
• /
• 1995.10a
• /
• pp.408-411
• /
• 1995

In this paper, we discuss the force control of flexible manipulators. Since the force control of flexible manipulators with planar one or two links using the distributed-parameter modeling has been the subject of a considerable number of publications until now, real time computations of the force control schemes are possible. But, application of those control schemes to multi-link spatial manipulators is fairly complicated. In this paper, we apply a concise hybrid position/force control scheme for a flexible manipulators. We use a lumped-parameter modeling for the flexible manipulators. The Hamilton's principle is applied to derive the equations of motion for the system and then, state-space model is obtained by the Lagrange's method. Finally, comparison of simulation results with experimental results is given to show the performance of our method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.3
• /
• pp.274-284
• /
• 2003

Multi-level converter that is high-capacity electric power conversion system is used widely to electric motor drive system and FATCs(Flexible AC Transmission Systems). H-Bridge converter has been prevalently applied to shunt-type system because it can be easily expanded to the multi-level. In steady states, converter is normally operated in the range of 0.7∼0.8 of modulation Index. Even though zero vectors are not imposed to high modulation index, DC-Link voltage Is constant. It means that converter has another boost vector except for zero vectors among several vectors in 3-level converter. This paper has examined the principle of boost vector and investigated the difference between another boost vector and zero vectors in 3-level converter. In addition, this paper has analysed and compared the charging currents and the capacitor voltages of two topologies. The currents and voltages are related to reference voltage. Therefore, it proposed the calculation method for the voltage ripple and the charging current of each capacitor and compared various DC-Link voltage control methods through the simulation.

• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.620-621
• /
• 2015

In this study, the multi-criteria decision-making model based on Quality Function Deployment Method is proposed. Multicriteria decision-making is an attempt to link QFD method with the TOPSIS. By this effort, a model that makes client's decision-making more rational and objective in design phase is suggested. The multi-criteria decisionmaking model confirming to the Owner's requirements will improve the productivity of the construction industry and the satisfaction of the customer. Further study extending the range of the requirements, not only the Owner's requirement will be necessary to cover the various factors as much as possible. And then, finally as a flexible platform to achieve a sustainable quality management, web-based multi-criteria decision-making model can be utilized by the relevant stakeholders simultaneously with the feed-back and sharing the necessary informations.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.1
• /
• pp.3-8
• /
• 2006

This paper deals with an automated computer-aided process planning and die design system by which designer can determine operation sequences even if they have a little experience in process planning and die design for axisymmetric products. An attempt is made to link programs incorporating a number of expert design rules with the process variables obtained by commercial FEM softwares, DEFORM and ANSYS, to form a useful package. The system can provide a flexible process based on either the reduction in the number of forming sequences by combining the possible two processes in sequence, or the reduction of deviation of the distribution on the level of the required forming loads by controlling the forming ratios. Especially in die design module optimal design technique and horizontal split of die insert were investigated for determining appropriate dimensions of components of multi-former die set. Results obtained, using the modules, enable the design and manufacture of a die set for a multi-former to be more efficiently performed.