• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.131-134
• /
• 1995

The high efficiency and accuracy in machining the die material can be abtained in high speed machining, so it is necessary to analyze the mechanism of high speed cutting process : cutting force, flank wear. The tool dynomometer with high natural frequency is newly developed. With this device, the mechanism of high speed cutting process is investigated according to speed and feedate.

• Wind and Structures
• /
• 제11권2호
• /
• pp.137-152
• /
• 2008

This paper discusses engineering aspects of the rear-flank downdraft that was recorded near Lubbock, Texas on 4 June 2002, and produced a gust wind speed nearly equal to the design value (50-year return period) for the region. The general characteristics of the storm, and the decomposition of the time histories into deterministic 'running mean' and random turbulence components are discussed. The fluctuating wind speeds generated by the event can be represented as a dominant low-frequency 'running mean' with superimposed random turbulence of higher frequencies. Spectral and correlation characteristics of the residual turbulence are found to be similar to those of high-frequency turbulence in boundary-layer winds. However, the low-frequency components in the running-mean wind speeds are spatially homogeneous, in contrast to the low-frequency turbulence found in synoptic boundary-layer winds. With respect to transmission line design, this results in significantly higher 'span reduction factors'.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.898-901
• /
• 2000

It is known that Si3N4 ceramic insert has less hardness than Al2O3 ceramic insert. But Si3N4 ceramic insert has not only high toughness and strength but also low thermal expansion coefficient, which makes it has longer tool life under thermal stress condition. In this study, commercial Si3N4 ceramic insert and home-made SiC-Si3N4 ceramic insert which has different sintering time and chemical composition is tested under various cutting conditions. The experimental result is compared in terms of tool life and cutting force. Generally, As the cutting speed and the feed rate increased, the cutting force and the flank wear increased too. The performance of SiC-Si3N4 ceramic insert shows the possibility to be a new ceramic tool.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.821-826
• /
• 2001

Out of all metal-cutting processes, the hole-making process is the most widely used. It is estimated to be more than 30% of the total metal-cutting process. It is therefore desirable to monitor and detect drill wear during the hole-drilling process. One important aspect in controlling the drilling process is monitoring drill wear status. Accordingly, this paper deals with Basic system and Online system. Basic system comprised of spindle rotational speed, feed rates, thrust, torque and flank wear measured tool microscope. Online system comprised of spindle rotational speed, feed rates, AE signal, flank wear area measured computer vision. On-line monitoring system does not need to stop the process to inspect drill wear. Backpropagation neural networks (BPNs) were used for on-line detection of drill wear. This paper deals with an on-line drill wear monitoring system to fit the detection of the abnormal tool state.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.459-464
• /
• 2001

A reliable tool wear monitoring technique is the one of important aspects for achieving an integrated and self-adjusting manufacturing system. In this paper, a tool wear estimation approach for turning is proposed. This approach uses the model of cutting force, spindle displacement and their relation. A series of experiments were conducted by designing experimental techniques to determine the relationship between flank wear and cutting force coefficient as well as cutting parameters such as cutting speed, depth of cut and feed. The proposed model performance has shown that the spindle displacement model predicts tool wear with high accuracy and spindle displacement signal is possible to replace cutting force signal.

• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.15-21
• /
• 1996

This study is focused on the prediction of appropriate tool life by clarifying the correlation between progressive tool wear and AE(Acoustic Emission) signals, while cutting stainless steel by end mill on the machining center. The results of this study were that RMSAE tends to increase linearly along with the increase of the cutting speed, and it was more sensitive to depth of cut than to the variation of feed rate at the same cutting conditions, and RMSAE increases around 0.21mm flank wear hereby AE-HIT also increases. AE signals depend upon tool wear and fracture from the above results. Therefore, the AE signals can be utilized in order to monitor the tool condition.

• 대한기계학회논문집
• /
• 제18권2호
• /
• pp.292-301
• /
• 1994

The resultant cutting force during machining with a worn tool is viewed as a decomposition of the cutting force into a cutting force component related to chip removal from the workpiece and into a component dependent on the contact force between the tool flank's wear land and the workpiece. The shear line method, in which the cutting force is considered proportional to the length of the shear line, is used to calculate the cutting force component for the removal of the chip, while the elastic effect of the workmaterial on the tool is taken into consideration to analyze the effect of tool flank wear. The predicted resultant cutting force, expressed as the sum of both components, is compared to experimental data obtained during wave-on-wave cutting.

• 한국정밀공학회지
• /
• 제15권8호
• /
• pp.116-125
• /
• 1998

In this paper, main target is to select parameters for prediction of tool wear and detection of tool fracture. The research about choosing parameter for prediction of tool wear is done by using force ratios. Also current sensor, tool-dynamometer, and accelerometer are used for researching detection method of tool fracture. Experiment is done using Taguchi's method in medium machining conditions. Parameter which is best for prediction of tool wear and detection of tool fracture by deviation analysis is selected. In this paper, tool wear means flank wear.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.74-79
• /
• 1996

The wear of partially coated pinion cutters under several cutting conditions was studied. In the realm of this experiment, chipping was a dominant tool wear mechanism and flank wear was much larger than crater wear. Under the condition of relatively low rotary feed and low radial feed rate, the wear due to chipping was concentrated at the nose part of pinion cutter. Increasing of rotary feed and radial feed rate alleviated the concentration of chipping at nose and prolonged tool life.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.555-559
• /
• 1996

Based on the general drill grinding mechanism, termed the helical grinding system, the conceptual design of 5 axes CNC drill grinding machine is proposed. Unique determination of the grinding parameters for precise production of the desired flank geometry is discussed by utilizing a mathematical model. Also, different combinations of grinding parameters are mentioned in order to produce various drill geometries (conical, cylindrical, and planar drill) on the single proposed CNC machine. A manual helical grinding machine has been fabricated and consequently helical drills have been ground in order to check the feasibility of the proposed grinding mechanism and its functionality.