• Design & Manufacturing
• /
• 제17권4호
• /
• pp.8-13
• /
• 2023

In this study, it was studied whether a new measurement factor "frictional vibration" that occurs due to the material flow of the die and sheet metal in the flange area during deep drawing process, could be measured using an vibration sensor. The blank holder force acting on the flange area during drawing processing acts as a friction force in the opposite direction into which the sheet material flows and causes friction vibration. As the blank holder force increases, the friction force increases, and as the blank holder force decreases, the friction force also decreases. Because of this, friction vibration also increases and decreases in proportion to the size of the blank holder force. According to this theory, whether frictional vibration occurs was measured using a flange simulator and a vibration sensor. The initial pressure was created using a torque wrench, and it was confirmed that the amplitude increased by about 4 times when torque 6 Nm was increased. When the forming velocity was rapidly changed to 300 mm/min, the amplitude increased approximately 4 times. It was confirmed that the amplitude of frictional vibration according to the measurement location was greater the further away from the specimen. It was verified that a new measurement factor "friction vibration" in the flange area can be measured and used for online monitoring.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권4호
• /
• pp.119-127
• /
• 2002

본 연구의 목적은 강관구조물에서 고력볼트로 인장접합되는 플랜지 이음의 거동을 연구하는데 목적이 있다. 9개의 플랜지 이음 실험체의 실험을 수행하였으며, 실험시 고력볼트의 변형율과 이음부의 변형율 그리고 변위를 측정하였다. 고력볼트의 변형율, 플랜지 사이에서 발생하는 지레반력 그리고 강관과 플랜지 판의 응력분포를 연구하였다. 원형강관 플랜지 이음 설계에 사용되는 기준식을 비교 분석하였다.

• Structural Engineering and Mechanics
• /
• 제83권3호
• /
• pp.341-351
• /
• 2022

During bolted flange assembly, the contact stiffness of some areas of the joint surface may be low due to the elastic interaction. In order to improve the contact stiffness at the lowest position of bolted flange, the correlation model between the initial bolt pre-tightening force and the contact stiffness of bolted flange is established in this paper. According to the stress distribution model of a single bolt, an assumption of uniform local contact stiffness of bolted flange is made. Moreover, the joint surface is divided into the compressive stress region and the elastic interaction region. Based on the fractal contact theory, the relationship model of contact stiffness and contact force of the joint surface is proposed. Considering the elastic interaction coefficient method, the correlation model of the initial bolt pre-tightening force and the contact stiffness of bolted flange is established. This model can be employed to reverse determine the tightening strategy of the bolt group according to working conditions. As a result, this provides a new idea for the digital design of tightening strategy of bolt group for contact stiffness of bolted flange. The tightening strategy of the bolted flange is optimized by using the correlation model of initial bolt pre-tightening force and the contact stiffness of bolted flange. After optimization, the average contact stiffness of the joint surface increased by 5%, and the minimum contact stiffness increased by 6%.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.37-46
• /
• 1999

Sheet pil VL 제조에 있어서 핵심적인 중요 기술은 압연 중 진행 소재가 좌우 휨이 없이 직진토록하여 치입 상에 문제가 없어야 하는 것이며, 또 하나는 압연 완료후 냉각 중에 있는 제품의 bending량을 최소로 하여 roller 교정기에서 1차 교정으로 교정이 완료되게 하는 것이다. 압연중 소재가 직진토록 하기 위해서 web와 flange 등의 caliber 협상에서 balance가 유지되어야 하므로, web와 flange의 reduction을 1:1 vs 1.0으로 web의 압하가 flange에 비해 10%정도 크게 하였고, 좌우 flange의 reduction이 변화하지 않도록 flange 온도 보존을 위하여 intermediated에서 2 pass를 생략하여 약 40초의 rolling time을 단축시켰고, 이는 7$0^{\circ}C$정도의 온도 drop를 방지하는 효과를 나타내었다. 이로 인한 roll force는 약 15%정도 down 되었다. 논리상으로 A3 변태점 이하에서 web(두꺼운 부분 24.3mm)나 flange(얇은부분 9.5mm)가 동시에 압연이 완료된다면 bending량은 휠씬 줄어든 것이나, 이 경우 roll force 증가에 따른 roll 절손 사고의 위험과 설비 trouble이 우려되기 때문에 web 온도를 약 95$0^{\circ}C$에서 flange 온도를 83.$0^{\circ}C$에서 압연 완료토록 함으로써 설비 안전을 도모하였고, 1차 교정을 위하여 냉각 주수 설비를 설치하여 공냉시켰을 때의 1400mm에서 700mm로 bending량을 감소시킴으로써 이를 가능토록하였다.

• 소성∙가공
• /
• 제7권1호
• /
• pp.36-48
• /
• 1998

In order to analyze the stretch flange forming characteristics of tailored blanks. laser welded blanks of different thickness and strength combinations were prepared and hole expansion tests were done. The stretch flange formability of laser welded blanks was reduced as increasing the deformation restraining force($strength{\times}thickness$) ratio between two welded sheets. Simulation of stretch forming mode deformation and comparson with experimental results showed that the stretch flange formabili-ty was influenced not only by the difference of the deformation restraining forces between two base sheets but also by the difference of the deformation restraining forces between base sheet and weld. Therefore the stretch flange formability was reduced more rapidly than tensile elongation as increas-ing the deformation restraining force ration. It was also found that simulation of stretch flange forming was more accurate when material properties of weld was given.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.9-13
• /
• 1999

In order to investigate the effect of flange wrinkling on the wall break of a deep drawn rectangular cup, experiments and simulation were done. The effect of the wrinkling height on drawing force and wall break for a moving blank holder system with spacer were studied by setting a fixed clearance between the drawing die and the blank holder. Simulation and experimental results showed that wall break could be provoked by the flange wrinkling. As the wrinkling height increased, the punch force grew. The maximum punch force was obtained at its final stage of stroke.

• 대한기계학회논문집A
• /
• 제20권7호
• /
• pp.2213-2222
• /
• 1996

This paper presents the design process and evaluaation results of a two-axis force transducer for measuring flange reaction forces. A double-cantilever beam structure is used as a sensing element, and its optimal configuration is determined based on the derived strain equations to maximize the sensitivity and minimize the regid body displacements. To reduce the coupling errors between two-axis forces, strain distributions by finite elemetns analysis are utilized and the Wheaststone bridge cricuits composed of strain gages are built such that the output voltage should be zero, although strains of four strain gages are not zero. Calibration test shows that the two-azxis force transducer developed in this paper is useful in measuring flange reaction forces within the coupling error of 5.53%.

• Design & Manufacturing
• /
• 제15권2호
• /
• pp.63-69
• /
• 2021

Springback is an essential task to be solved in order to make high-precision products in sheet metal forming. In this study, materials with four different elastic regions were used. For the forming analysis, the change of springback caused by the frictional force generated in the flange part during hat shape forming was considered by using the AutoForm analysis program. Factors affecting frictional force were blank holder force, friction coefficient, bead R and bead height. As a result of the forming analysis, the springback increases as the material with a larger elastic region increases. In addition, as the frictional force of the flange part increased, the tensile force in the forming direction increased and the springback decreased. In particular, the blank holder force and friction coefficient had a great effect on springback in mild materials (DC04, Al6016), and the bead effectively affects all materials. Through this study, it was considered that the springback decreased as the material with a smaller elastic region and the tensile force in the forming direction increased.

• International Journal of Railway
• /
• 제3권2호
• /
• pp.60-67
• /
• 2010

This paper deals with an experimental study on the wheel flange climbing of railway vehicles, which is a major factor leading to derailment. An experiment is carried out on a 1/5-scale model wheelset of a truck used on a standard-gauge track, which is placed on a roller rig. The lateral external force acting on the wheelset is ramped up until derailment occurs under the condition of a fixed attack angle and wheel-load unbalance ratio. Three parameters, the height of wheel lift, the lateral force, and the wheel load acting on the outer rail, are measured until derailment occurs. From these measurements, it is possible to observe the behavior of the wheelset and to elucidate how the attack angle, the wheel-load unbalance ratio and the lateral external force affect flange-climb derailment. Then, a numerical simulation is carried out using an analytical model based on a single wheelset. As a result, the flange-climb behavior observed in the experiment can be explained theoretically on the bases of the analytical results, although further improvement of the model is desired.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.123-127
• /
• 1996

The tendency of wrinkling formation on the flange of a deep-drawn rectangular container was investigated experimentally under different process conditions. Such process variables as blank size, sheet thickness, blank-holding force, and depth of drawing are chosen to examine their effects on the flange wrinkles of the products. Number and amplitudes of the wrinkles are measured along the periphery of the flange and compared between each case of process condition.