• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.177-179
• /
• 2012

This work presents an experimental investigation to study $NO_x$ emissions under stoichiometric air ratio and elevated pressure (2~10bar) in a High Press Combustor(HPC) equiped with double cone burner which was designed by Pusan Clean Coal Center(PC3). Exaust gas temperature and $NO_x$ emissions were measured at the end of the combustion chamber. The $OH^*$ radical concentration and $NO_x$ emission were decreased as a function of increasing ${\lambda}$ generally. On the other hand, $OH^*$ radical concentration and $NO_x$ emission increased with ${\lambda}$ pressure of the combustion chamber. $NO_x$ emissions which were governed by thermal $NO_x$, were highly increased under the elevated pressure, but slightly increased at sufficiently low fuel concentrations (${\lambda}>2.0$).

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.211-219
• /
• 1996

In a small high-speed D. I. diesel engine, the injected fuel spray into the atmosphere of the high temperature is burnt by go through the process of break up, atomization, evaporation and process of ignition. These process are important to decide the emission control and the rate of fuel consumption and out put of power. Especially, in the case of injected fuel spray impinging on the wall of piston cavity, the geometry of piston cavity gives great influence the ignitability of injected fuel and the flame structure. Ordinary, the combustion chamber of driving engine have unsteady turbulent flow be attendant on such as the change of temperature, velocity and pressure. So the analysis of spray behavior is difficult. In this study, the spray was impinged on the wall of 3 types of piston cavity such as Dish, Toroidal, Re-entrant type, in order to analyze the combustion process of impinging spray precisely and systematically. And hot wire probe was used for analyze non-steady flow characteristics of impinging spray, and to investigate the behavior of spray, the aspects of concentration c(t), standard deviation σ(t) and variation factor(vf) was measured with the lapse of time.

• Journal of Welding and Joining
• /
• 제17권4호
• /
• pp.53-59
• /
• 1999

Amorphous alloys have also been called glassy alloys or non-crystalline alloys. They are made by the rapid solidification. The solidification occurs so rapid that the atoms are frozen in their liquid configuration. There are unique magnetic, mechanical, electrical and corrosive behaviors which result form their amorphous structure. In the study. amorphous coatings were manufactured with Ni-Cr-B-Si powders by flame spray. Measurement of hardness, were resistance, corrosion resistance and observation of microstructures and XRD, DSC were performed to investigate characteristics of amorphous coatings. The experimental results obtained as follow: 1) Amorphous powders could not be manufactured with the spraying in the spraying in the liquid nitrogen. But, amorphous coatings could be manufactured with the rotation cooling method by liquid nitrogen. In the fabrication of amorphous coatings, major factor was the rapid cooling by rotation of the substrate. 2) Hardness of coatings was obtained Hv 960 by formation of amorphous phase. But, wear resistance decreased. That was due to porosity in the coatings by the rapid cooling. 3) In the case of corrosion resistance, amorphous coatings were superior to air-cooled coatings. That was due to formation of amorphous phase. 4) After amorphous coatings were heat-treated at 520℃ for 1hr. hardness increased 80% and wear resistance increased 30% comparing with air cooled coatings. These were due to crystallization of amorphous phase and decrease of porosity by heat-treatment.

• 한국연소학회지
• /
• 제9권2호
• /
• pp.38-44
• /
• 2004

The evolution of incipient soot particles has been examined by high resolution electron microscopy (HRTEM) and elemental analyzer in ethylene-air inverse diffusion flames. Laser Induced Incandescence(LII) and laser scattering methods were introduced for examining the soot volume fraction and morphological properties in combustion generated soot qualitatively. Soot particles, collected by thermophoretic sampling, were analyzed by using HRTEM to examine the nano structure of precursor particles. HRTEM micrographs apparently reveal a transformation of condensed phase of semitransparent tar-like material into precursor particles with relatively distinct boundary and crystalline which looks like regular layer structures. During this evolution histories, C/H analysis was also performed to estimate the chemical evolution of precursor particles. The changes of C/H ratio of soot particles with respect to residence time can be divided into two parts: one is a very slowly increasing regime where tar-like materials are transformed into precursor particles (inception process) the other is an increasing region with constant rate where surface growth affects the increase of C/H ratio dominantly (surface growth process). These results provide a clear picture of a transition to mature soot from precursor materials.

• 한국세라믹학회지
• /
• 제43권9호
• /
• pp.544-551
• /
• 2006

The sealing technique between a glass tube and a copper heat pipe in an evacuated tube solar collector is studied. In this study two different sealing techniques, such as flame method and furnace firing, are examined. After the sealing of a copper to a glass, the oxidation state of the copper and its bonding morphology were examined by SEM and XRD. Its oxidation was retarded by coating of borate solution on the copper, and $Cu_2O(cuprite)$ turned into CuO(tenorite) with increase in a firing temperature and firing time. Porous structure was found in the oxide layer when CuO formed. The best sealing morphology was observed when the thickness of the oxidation layer was less than $20{\mu}m$. The sealing technique performed in a furnace was promising and the satisfactory result was obtained when the sample was fired at $950^{\circ}C$ for 5 min under $N_2$ atmosphere. Annealing procedure is recommended to remove the stress left at the bonding zone.

• 한국결정성장학회지
• /
• 제9권3호
• /
• pp.289-294
• /
• 1999

The charged clusters or particles, which contain hundreds to thousands of atoms or even more, are suggested to from in the gas phase in the thin film processes such as CVD, thermal evaporation, laser ablation, and flame deposition. All of these processes are also phase synthesis of the nanoparticels. Ion-induced or photo-induced nucleation is the main mechanism for the formation of these nanoclusters or nanoparticles in the gas phase. Charge clusters can make a dense film because of its self-organizing characteristics while neutral ones make a porous skeletal structure because of its Brownian coagulation. The charged cluster model can successfully explain the unusual phenomenon of simultaneous deposition and etching taking place in diamond and silicon CVD processes. It also provides a new interpretation on the selective deposition on a conducting material in the CVD process. The epitaxial sticking of the charged clusters on the growing surface is getting difficult as the cluster size increases, resulting in the nanostructure such as cauliflower or granular structures.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.85-88
• /
• 2010

본 연구에서는 액체로켓 분사기에서 임계압력 이상의 추진제의 혼합과 연소과정을 수치적으로 모사하여 분석하고자 하였다. 이 과정에서 확장된 $k-{\varepsilon}$ 난류 모델을 이용하여 난류 속도장을 예측하였고 고압에서의 실제 유체 효과를 고려하기 위하여 혼합 추진제의 물성치는 SRK 상태 방정식을 이용하여 계산하였다. 또한 난류 확산 화염에서의 좀 더 정확한 난류와 화학반응의 상호작용을 고려하기 위하여 실제 유체 효과를 고려할 수 있는 층류 화염편 모델을 이용하였다. 수치적인 계산을 바탕으로 이상기체 가정을 사용한 결과와 비교하여 실제 유체의 효과와 기체메탄/액체산소 동축 전단 분사기의 제트화염 구조를 상세하게 살펴보았다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.9-12
• /
• 2010

본 논문은 연료 과농 연소 환경 하의 이중 와류 동축형 분사기의 유량 통과 특성 파악을 위해 수행한 실험결과를 수록하였다. 액체산소와 케로신(Jet A-1)을 사용하여 연소시험을 수행하고 유량 통과 특성을 유량계수로 표현하였다. 유량계수 산출을 위해 유량, 압력, 온도를 계측하였다. 연료 분사기의 경우, 산화제 측 분사기 형상, 연소압, 혼합비에 관계없이 일정한 유량 계수 값을 보였다. 이에 반해 산화제 분사기는 연소압과 혼합비 변화에 영향을 받는 것으로 나타났다. 화염 형성 변화가 유량계수 변화에 특히 산화제 측에 영향을 주고 있음을 밝혔다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.803-810
• /
• 2017

초임계 조건에서의 연소반응에서는 액체산소가 초임계 상태로 천이되며 스도보일링과 급격한 물성치변화를 발생시킨다. 이때 초임계 상태에서 작동하는 분사기의 연소반응은 급격한 밀도차로 인한 난류확산에 의해 지배되며, 따라서 스도보일링과 함께 발생하는 확산유동에 대한 연구가 필요하다. 많은 연구자들에 의해 초임계 연소해석에서 발생하는 이 현상들에 대한 연구가 진행되었지만 다양한 변수들에 의한 사례연구가 부족한 상태이다. 본 연구에서는 초임계 압력조건에서 산화제-연료비(O/F)와 연소기 직경, 리세스비를 통해 재순환유동 및 액체산소코어 길이에 변화를 주어 이로 인한 유동구조 및 화염구조의 변화를 수치적으로 연구하였다.

• 대한기계학회논문집
• /
• 제11권3호
• /
• pp.479-487
• /
• 1987

본 연구에서는 액적들의 분포상태가 집단연소의 특성에 미치는 영향을 규명하 기 위하여 김의 비정상 집단연소모델에 비균일 액적크기분포와 수밀도분포를 고려한 비균일분포 집단연소모델을 구성하여 이론적으로 해석하였다.