• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.8
• /
• pp.743-752
• /
• 2013

This is the second paper on the combustion characteristics of landfill gas in a constant volume combustion chamber for a large displacement volume commercial engine, and it discusses the combustion process on the basis of pressure measurements. The results show that the bimodal peak pressure phenomenon, which is caused by the interaction of the heat release and the heat transfer, is more apparent as the mixtures are more favorable to combustion, and the magnitudes of the pressures depend on the unburned fraction. In addition, there exist four main inflection points during heat release owing to variations in the heat transfer area related to flame propagation from the ignition point. Furthermore, the number of inflection points increases as the mixture quality worsens because of the extended burn duration. Consequently, the sophisticated interactions between the heat transfer area changing pattern due to flame propagation and transfer duration might cause very peculiar heat release patterns.

• 연구논문집
• /
• s.33
• /
• pp.5-16
• /
• 2003

Fuel distribution, combustion, and flame propagation characteristics of heavy duty engine with the liquid phase LPG injection(LPLI) were studied in a single cylinder engine. Optically accessible single cylinder engine and laser diagnostics system were built for quantifying fuel concentration by acetone PLIF(planar laser induced fluorescence) measurements. In case of Otto cycle engine with large bore size, the engine knock and thermal stress of exhaust manifold are so critical that lean burn operation is needed to reduce the problems. It is generally known that fuel stratification is one of the key technologies to extend the lean misfire limit. The formation of rich mixture in the spark plug vicinity was achieved by open valve injection. With higher swirl strength(Rs=3.4) and open valve injection, the cloud of fuel followed the flow direction and the radial air/fuel mixing was limited by strong swirl flow. It was expected that axial stratification was maintained with open-valve injection if the radial component of the swirling motion was stronger than the axial components. The axial fuel stratification and concentration were sensitive to fuel injection timing in case of Rs=3.4 while those were relatively independent of the injection timing in case of Rs2.3. Thus, strong swirl flow could promote desirable axial fuel stratification and, in result, may make flame propagation stable in the early stage of combustion.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2010.04a
• /
• pp.59-63
• /
• 2010

Seven different size of orifice were applied in a constant volume combustion chamber for evaluating the effects of torch-ignition on combustion. The initial flame development and flame propagation were analyzed by the mass fraction burn and combustion enhancement rate. The combustion pressures were measured to calculate the mass fraction burn and the combustion enhancement rates. In addition, the flame propagations were visualized by the shadowgraph method for the qualitative comparison. The result showed that the combustion pressure and mass burned fraction were increased when using the torch-ignition device. The combustion enhancement rates of torch-ignition cases were improved in comparison with conventional spark ignition. Finally, the visualization results showed that the torch-ignition induced faster burn than conventional spark ignition due to the earlier transition to turbulent flame and larger flame surface, during the initial stage.

• Journal of the Korean Society of Safety
• /
• v.13 no.2
• /
• pp.88-95
• /
• 1998

Five parts of the automotive interior materials were sampled to determine their combustion characteristics. Oxygen Indexer, Smoke chamber, Differential Scanning Calorimeter(DSC) were used as the analysis apparatus. All LOI values of samples appear less than 21. The combustion phenomena of the interior materials primarily depends on properties of each layer material. The amount of generated smoke are reached the maximum value within 30 - 90sec after ignition. The experimental results of combustion characteristics and DSC of H/Line also indicated that the layer of foam was melt first and it caused the propagation of flame through the sample. The combustion characteristics of multi-layer materials primarily depends on thermal characteristics of single layer material.

• Journal of ILASS-Korea
• /
• v.2 no.2
• /
• pp.24-34
• /
• 1997

This paper describes the investigation of combustion characteristics of gasoline-methanol blend in constant volume combustion chamber. A constant volume combustion chamber was used to elucidate a basic combustion characteristics and the premixer was installed to control temperature and equivalence ratio. And the maximum pressure, combustion duration and flame propagation according to the evaporation rate were measured to determine the optimal temperature range for evaporating a blend fuel. These experimental results indicate that the combustion characteristics such as combustion chamber pressure and combustion were deteriorated by decreasing surrounding temperature of fuel. These experimental results indicate that the combustion characteristics such as combustion chamber pressure and combustion were deter orated by decreasing surrounding temperature of fuel injected. It was also found that the overall gasification process for methanol blend fuel was influenced by a combustion chamber temperature rather than a premixer temperature.

• Journal of the Korean Society of Safety
• /
• v.19 no.4 s.68
• /
• pp.150-154
• /
• 2004

Gas explosion characteristics of hydrogen and liquefied petroleum gas(LPG) were measured in 6L cylindrical vessel, and experiment for explosion to fire transition phenomena of the gases were carried out using the 270L vessel. Explosion characteristics were measured using the stain type pressure transducer and explosion to fire transition phenomena was analyzed with the hish-speed camera. Base on the experiment, it was found that explosion pressure was most high slightly above the stoichiometric concentration, and explosion pressure rise rate and flame propagation velocity were proportional to the combustion velocity. And we find that those kind of explosion characteristics affect the explosion-to-fire transition, in addition, explosion flame temperature, flame residence time, are important parameters in explosion-to-fire transition.

• Journal of Hydrogen and New Energy
• /
• v.24 no.3
• /
• pp.242-248
• /
• 2013

The purpose of this study is to obtain low-emission and high-efficiency by hydrogen enriched LPG fuel in LPG engine and is to clarify the effects of hydrogen enrichment in LPG fuelled engine on exhaust emission and performance. An experimental study was carried out to obtain fundamental data for performance and emission characteristics of hydrogen enrichment in LPG engine. The research was held by changing the hydrogen ratio to 0, 5, 10, 20% in 1500rpm, bmep 2 and 4bar. The result turned out that the combustion duration was shortened due to fast flame propagation of hydrogen. And the amount of Carbon dioxide and Hydrocarbon decreased. However, the amount of NOX increased, which is thought to be the result of high adiabatic flame temperature of hydrogen. It has been confirmed that this phenomenon has changed by the Hydrogen mixing ratio.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.3
• /
• pp.368-377
• /
• 2012

Most tunnel simulations have been focused on the thermal field and the critical velocity for suppression of hot back-layering flow in case of fire and on the characteristics of a tunnel fire in terms of the flame propagation and the toxic gas generation. In this paper, a comparative study of the flow characteristics of polluted air with no heat source in a tunnel model opened and closed at both end sides is implemented into a recognized CFD simulation code. The model is used to investigate the flow characteristics depending on the three different Reynolds numbers of 640, 1270 and 2120, which have been chosen by the flow velocities of 0.3, 0.6 and 1.0 m/s through the inlet. The results of this study have shown that the CFD predictive and experimental approaches are available in qualitatively studying the correlation of flow behaviors for a better tunnel design.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.211-218
• /
• 1997

Five parts of vehicle upholsteries were sampled to determine its combustion characteristics. Oxygen Indexer, Smoke chamber, Differential Scanning Calorimetry(DSC) are applied as the analysis apparatus. All LOI values of samples appear less than 21. The combustion phenomena of vehicle upholster primarily depends on properties of each layer material. The amount of smoke generated is the experiment reached the maximum value within 30-90sec after ignition. The experimental results of combustion characteristics and DSC of H/Line also indicated that the layer of foam was melt first and it caused the propagation of flame through the sample. The combustion characteristics of multi layer materials primarily depend on thermal characteristic of single layer material.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1996.11a
• /
• pp.43-48
• /
• 1996

It is considered that automobile inner space is dangerous due to its combustion characteristics. (Automobile interior is largely made by plastic materials.) At last it is necessary to study on combustion characteristics of automobile interior. we could obtain its rapid combustion velocity and high smoke density by using ASTM D 2863 apparatus, DSC (Differential Scanning Calorimetry), Smoke density apparatus and so on. The study is summerized by following conditions and results. 1. Sample size was 150mm(length)$\times$60mmwidth). 2. Combustion velocity appeared peak point in the 2cm point. 3. PVC and foam layers are important factors in the face of smoke density. 4. Using DSC, we obtained the point that automobile interior was melted. 5. Automobile interior should be improved because of its low L.O.I value and rapid flame propagation velocity.