• Corrosion Science and Technology
• /
• v.6 no.6
• /
• pp.316-321
• /
• 2007

The effect of annealing on the pitting corrosion resistance of anodized Al-Mg alloy (AA5052) processed by equal-channel angular pressing (ECAP) was investigated by electrochemical techniques in a solution containing 0.2 mol/L of $AlCl_3$ and also by surface analysis. The Al-Mg alloy was annealed at a fixed temperature between 473 and 573 K for 120 min in air after ECAP. Anodizing was conducted for 40 min at $100-400A/m^2$ at 293 K in a solution containing 1.53 mol/L of $H_2SO_4$ and 0.0185 mol/L of $Al_2(SO_4)_3$. The internal stress generated in anodic oxide films during anodization was measured with a strain gauge to clarify the effect of ECAP on the pitting corrosion resistance of anodized Al-Mg alloy. The time required to initiate the pitting corrosion of anodized Al-Mg alloy was shorter in samples subjected to ECAP, indicating that ECAP decreased the pitting corrosion resistance. However, the pitting corrosion resistance was greatly improved by annealing after ECAP. The time required to initiate pitting corrosion increased with increasing annealing temperature. The strain gauge attached to Al-Mg alloy revealed that the internal stress present in the anodic oxide films was compressive stress, and that the stress was larger with ECAP than without. The compressive internal stress gradually decreased with increasing annealing temperature. Scanning electron microscopy showed that cracks occurred in the anodic oxide film on Al-Mg alloy during initial corrosion and that the cracks were larger with ECAP than without. The ECAP process of severe plastic deformation produces large internal stresses in the Al-Mg alloy; the stresses remain in the anodic oxide films, increasingthe likelihood of cracks. It is assumed that the pitting corrosion is promoted by these cracks as a result of the higher internal stress resulting from ECAP. The improvement in the pitting corrosion resistance of anodized AlMg alloy as a result of annealing appears to be attributable to a decrease in the internal stresses in anodic oxide films

• 한국벤처창업학회:학술대회논문집
• /
• 2007.11a
• /
• pp.143-174
• /
• 2007

The objective of Starts-up education rears leading company that minimize a risk & connect them with successful idea. Internet Starts-up education is serviced in public & civil parts, it is insufficient to reach successful Starts-up support. This study is targeting on review the present condition of the Internet Starts-up education, research which it sees Internet Starts-up education actual condition investigation through investigation student of education satisfactorily and education contents and the plan to grope an Starts-up education progress coat problem and developmental plan it did. The current events point which has become research result escape first, age of the students of education, followed in educational background and, education motive and education experience presence education satisfactory boat song it appeared in these demand different, base grudge the form which is various it fixed and the education was demanded. Second, currently the department of pedagogy joining in establishment leader against the technical element which is advanced swip, the education reinforcement against an enterprise accomplishment ability back human factor, an enterprise propulsion environment and an enterprise item back enterprise environment element was demanded. Time after support and consulting, completion lifestyle community construction, completion lifestyle for item connection support and the trade name net after third, establishing an enterprise we the king, after toe ring back educating which carries on shoulder the importance of the civil official was embossed. The study which it sees led and like this investigation analysis the education progress for the successful support of the Internet Starts-up and time after connection setup construction it led and the plan which it will put out advancement of Starts-up education and it groped.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.5
• /
• pp.543-561
• /
• 2020

This paper is the result of the study on the effect of the support structure of the tunnel steel rib. In tunnel excavation, the top and bottom half excavation methods result in subsidence of steel rib reinforcement due to insufficient support of steel rib reinforcement when the ground is poor after excavation. The foundation of the steel rib installed in the upper half excavates the bottom part of the base, causing the subsidence to occur due to various effects such as internal load and lateral pressure. As a result, the tunnel is difficult to maintain and its safety is problematic. To solve these problems, steel rib support structures have been developed. For the purpose of verification, the behavior of the supporting structure is verified by model experiments reduced to shotcrete and steel rib material similarity, the numerical analysis of ΔP and ΔP generated by bottom excavation by Terzaghi theoretical equation. As a result, it was found that the support structure of 20.100~198.423 kN is required for the 10~40 m section of the depth for each soil of weathered soil~soft rock. In addition, as a result of the reduced model experiment, a fixed level of 50% steel rib deposit of steel rib support structure was installed. The study shows that the installation of steel rib support structures will compensate for uncertainties and various problems during construction. It is also thought that the installation of steel rib support structure will have many effects such as stability, economy, and air reduction.

• Journal of Korea Water Resources Association
• /
• v.46 no.9
• /
• pp.921-932
• /
• 2013

Runoff data availability is a substantial factor for precise flood control such as flood frequency or flood forecasting. However, runoff depths and/or peak discharges for small watersheds are rarely measured which are necessary components for hydrological analysis. To compensate for this discrepancy, a lumped concept such as a Storage Function Method (SFM) was applied for the partitioned Choongju Dam Watershed in Korea. This area was divided into 22 small watersheds for measuring the capability of spatial extension of runoff data. The chosen total number of flood events for searching parameters of SFM was 21 from 1991 to 2009. The parameters for 22 small watersheds consist of physical property based (storage coefficient: k, storage exponent: p, lag time: $T_l$) and flood event based parameters (primary runoff ratio: $f_1$, saturated rainfall: $R_{sa}$). Saturated rainfall and base flow from event based parameters were explored with respect to inflow at Choongju Dam while other parameters for each small watershed were fixed. When inflow of Choongju Dam was optimized, Youngchoon and Panwoon stations obtained average of Nash-Sutcliffe Efficiency (NSE) were 0.67 and 0.52, respectively, which are in the satisfaction condition (NSE > 0.5) for model evaluation. This result is showing the possibility of spatial data extension using a lumped concept model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.69-76
• /
• 2018

The present study analyzed the effect of film hole position of 45 degree ribbed cooling channel on film cooling performance of gas turbine blades. We also investigated the influence of the ribs under the fixed blowing ratio. Three-dimensional numerical model was constructed and extensive simulation was conducted using the commercial code (Fluent ver. 17.0) under steady-state condition. Base on the simulation results, We investigated the cooling effectiveness, flow velocity, streamline, and pressure coefficient. Moreover, We analyzed the effect of cooling hole position on ejection of the secondary flow caused by the rib structure. From the results, It was found that internal flow of the cooling channel forms a vortex pair in the counterclockwise from the top side, and clockwise from the bottom side. For the channels with ribs, the vortex flow generated by the ribs caused a higher pressure difference near the hole outlet, resulting in at least 12% higher cooling effectiveness than the channel without ribs. Additionally, when the hole is located on the left side of the ribbed channel (Rib-Left), it can be found that the secondary flow generated by the ribs hits against wall surface near the hole to form a flow in the direction of the hole inclination angle. Therefore, It is considered that the region where the cooling gas discharged to the blade surface stays in the main flow boundary layer is wider than the other cases. In this case, The largest pressure coefficient difference was observed near the outlet of the hole, and as a result, the discharge of the cooling gas was accelerated and the cooling efficiency was slightly increased.

• Molecules and Cells
• /
• v.25 no.4
• /
• pp.467-478
• /
• 2008

Simple sequence repeats (SSRs) and interSSR (ISSR) marker systems were used in this study to reveal genetic changes induced by artificial selection for short/long larval duration in the tropical strain Nistari of the silkworm Bombyx mori. Artificial selection separated longer larval duration (LLD) ($29.428{\pm}0.723days$) and shorter larval duration (SLD) ($22.573{\pm}0.839days$) lines from a base, inbred population of Nistari (larval span of $23.143{\pm}0.35days$). SSR polymorphism was observed between the LLD and SLD lines at one microsatellite locus, Bmsat106 ($CA_7$) and at two loci of 1074 bp and 823 bp generated with the ISSR primer UBC873. Each of these loci was present only in the LLD line. The loci segregated in the third generation of selection and were fixed in opposite directions. In the $F_2$ generation of the $LLD{\times}SLD$ lines, the alleles of Bmsat106 and $UBC873_{1074bp}$ segregated in a 1:1 ratio and the loci were present only in the LLD individuals. $UBC873_{823bp}$ was homozygous. Single factor ANOVA showed a significant association between the segregating loci and longer larval duration. Together, the two alleles contributed to an 18% increase in larval duration. The nucleotide sequences of the $UBC873_{1074bp}$ and $UBC873_{823bp}$ loci had 67% A/T content and consisted of direct, reverse, complementary and palindromic repeats. The repeats appeared to be "nested" (59%) in larger repeats or as clustered elements adjacent to other repeats. Of 203 microsatellites identified, dinucleotides (67.8%) predominated and were rich in A/T and T/A motifs. The sequences of the $UBC873_{1074bp}$ and $UBC873_{823bp}$ loci showed similarity (E = 0.0) to contigs located in Scaffold 010774 and Scaffold 000139, respectively, of the B. mori genome. BLASTN analysis of the $UBC873_{1074bp}$ sequence showed significant homology of (nt.) 45-122 with upstream region of three exons from Bombyx. The complete sequence of this locus showed ~49% nucleotide conservation with transposon 412 of Drosophila melanogaster and the Ikirara insertions of Anopheles gambiae. The A + T richness and lack of coding potential of these small loci, and their absence in the SLD line, reflect the active process of genetic change associated with the switch to short larval duration as an adaptation to the tropics.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.1 no.1
• /
• pp.65-72
• /
• 2003

Adsorption and desorption characteristics of methyl iodide at high temperature conditions up to 25$0^{\circ}C$ by TEDA-impregnated activated carbon and silver-ion exchanged zeolite(AgX-10), which are used for radioiodine retention in nuclear facility, were experimentally evaluated. In the range of temperature from 3$0^{\circ}C$ to 25$0^{\circ}C$, the adsorption capacity of base activated carbon decreased sharply with increasing temperature but that of TEDA-impregnated activated carbon showed higher value even at high temperature ranges. Especially, the residual amount of methyl iodide after desorption on TEDA-AC represented 30% lower value than that on AgX-10. However, it can be used as an adsorbent for the removal of methyl iodide up to 15$0^{\circ}C$ if it is preventing explosion by Ignition. The breakthrough curves of methyl iodide in the fixed bed packed with AgX-10 uP to 40$0^{\circ}C$ were compared upon the effects of bed temperatures, bed depth and input concentration of methyl iodide. Removal mechanism of methyl iodide on AgX-10 was proposed, based on the analysis of by-product gas generated from adsorption reaction.

• Journal of Digital Convergence
• /
• v.18 no.1
• /
• pp.35-44
• /
• 2020

The purpose of this paper is to investigate various factors affecting the efficiency of China IC industry, reflecting the resource utilization and overall development level of China IC industry. In this paper, three input indicators (R&D Expenditure, Cash paid to and for employees, Total fixed assets) and two output indicators (Net profit, Sales revenue) were selected for 17 listed companies in the IC industry with operating profit of less than 1 billion yuan in 2018 and applied the technology efficiency theory and DEA analysis method to analyze the relative efficiency of the output base. The study found that one of the 17 companies analyzed was efficient, two were inefficient on an inadequate scale, and the rest were inefficient due to insufficient production technology, scale and management level. This study argues that enterprises should reduce resource input appropriately and strengthen scientific and technological innovation management to maximize resource utilization efficiency. Therefore, this study has important practical significance for improving the efficiency of IC enterprises. The Malmquist method will be used to study the total factor productivity of small and Medium-sized companies in IC industry.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.3 no.1
• /
• pp.29-55
• /
• 2008

The objective of Starts-up education rears leading company that minimize a risk & connect them with successful idea. Internet Starts-up education is serviced in public & civil parts, it is insufficient to reach successful Starts-up support. This study is targeting on review the present condition of the Internet Starts-up education, research which it sees Internet Starts-up education actual condition investigation through investigation student of education satisfactorily and education contents and the plan to grope an Starts-up education progress coat problem and developmental plan it did. The current events point which has become research result escape first, age of the students of education, followed in educational background and, education motive and education experience presence education satisfactory boat song it appeared in these demand different, base grudge the form which is various it fixed and the education was demanded. Second, currently the department of pedagogy joining in establishment leader against the technical element which is advanced swip, the education reinforcement against an enterprise accomplishment ability back human factor, an enterprise propulsion environment and an enterprise item back enterprise environment element was demanded. Time after support and consulting, completion lifestyle community construction, completion lifestyle for item connection support and the trade name net after third, establishing an enterprise we the king, after toe ring back educating which carries on shoulder the importance of the civil official was embossed. The study which it sees led and like this investigation analysis the education progress for the successful support of the Internet Starts-up and time after connection setup construction it led and the plan which it will put out advancement of Starts-up education and it groped.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.31 no.5
• /
• pp.901-909
• /
• 2021

Since mobile devices have limited computational resources, it tends to use the cloud to compute or store data. As real-time becomes more important due to 5G, many studies have been conducted on edge clouds that computes at locations closer to users than central clouds. The farther the user's physical distance from the edge cloud connected to base station is, the slower the network transmits. So applications should be migrated and re-run to nearby edge cloud for smooth service use. We run applications in docker containers, which is independent of the host operating system and has a relatively light images size compared to the virtual machine. Existing migration studies have been experimented by using network simulators. It uses fixed values, so it is different from the results in the real-world environment. In addition, the method of migrating images through shared storage was used, which poses a risk of packet content exposure. In this paper, Containers are migrated with Secure CoPy(SCP) method, a data encryption transmission, by establishing an edge computing environment in a real-world environment. It compares migration time with Network File System, one of the shared storage methods, and analyzes network packets to verify safety.