• Korean Chemical Engineering Research
• /
• v.43 no.5
• /
• pp.560-565
• /
• 2005

Catalytic performances of zeolite catalysts such as H-mordenite(HM), H-Beta$(H{\beta})$, H-USY(HUSY) for the transmethylation between 1-methylnaphthalene(1-MN) and 2-methylnaphthalene(2-MN) were investigated in a fixed-bed flow reactor. $H{\beta}$ showed higher and more stable conversion than others to exhibit a high and stable 2-MN/1-MN ratio of 2.3 and 2,6-DMN/2,7-DMN ratio of 1.3 at the $1^{st}$ hour of time on stream under the reaction conditions as follows: reaction temperature of $350^{\circ}C$, reaction pressure of 1.5 MPa, WHSV of $2.7g_{feed}/g_{cat}{\cdot}h$ and the molar ratio of 1-MN and 2-MN of 1:1. The catalytic behavior has been discussed in relation with the catalyst pore structure and acidity.

• Journal of Energy Engineering
• /
• v.2 no.2
• /
• pp.208-214
• /
• 1993

Pyrolysis of bituminous coal has been carried out in a two-stage fixed bed reactor to produce high heating value gas(7000 kcal/N㎥) for industrial or town gas usage. The effects of coke catalyst, pyrolysis temperature (468∼565$^{\circ}C$), and catalytic cracking temperature (700∼850$^{\circ}C$) on the product gas properties from pyrolysis of bituminous coal have been determined. From pyrolysis of Dong Jin coal with coke, the carbon deposition on catalyst is found to be less than 5% of product tar and approximately 15% of total energy iii the parent coal can be recovered as high heating value gas. Oil composition in the product tar from the two-stage pyrolysis is higher than that from low-temperature pyrolysis. The tar produced from pyrolysis below 516$^{\circ}C$ can be easily catalytically cracked but, the tar produced above 565$^{\circ}C$ cannot be cracked easily with catalyst. From the product gas analysis, the catalytic cracking temperature should be maintained below 800$^{\circ}C$ since cracking speed of ethylene increases remarkably with the cracking temperature above 800$^{\circ}C$.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.4
• /
• pp.289-295
• /
• 2003

Synthesis gas is produced commercially by a steam reforming process. However, the process is highly endothermic and energy intensive. Thus, this study was conducted to produce synthesis gas by the partial oxidation of methane to cut down the energy cost. Supported Ni catalysts were prepared by the impregnation method. To examine the activity of the catalysts, a differential fixed bed reactor was used, and the reaction was carried out at $750{\sim}850^{\circ}C$ and 1 atm. The fresh and used catalysts were characterized by XRD, XPS, TGA and AAS. The highest catalytic activity was obtained with the 13wt% Ni/MgO catalyst, with which methane conversion was 81%, and $H_2$ and CO selectivities were 94% and 93%, respectively. 13wt% Ni/MgO catalyst showed the best $MgNiO_2$ solid solution state, which can explain the highest catalytic activity of the 13wt% Ni/MgO catalyst.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.624-628
• /
• 1998

The aromatic organic solvents(BTX) were decomposed in the fixed bed reactor packed with a 0.5% $Pt/{\gamma}-Al_2O_3$ catalyst, then, supercritical carbon dioxide(SC-$CO_2$) was used as the reaction media. And the conversion was dependent on the inlet concentration of BTX and the molar density of SC-$CO_2$. The conversion of BTX was decreased with increasing of inlet concentration, and was increased with temperature and pressure. The maximum conversion of benzene was 98.5% at $300^{\circ}C$ and 204.1 atm, and that of toluene and xylene were 82.0 and 76.5%, respectively, at $350^{\circ}C$ and 204.1 atm. The intermediate products of partial oxidation were identified as benzaldehyde, phenol, benzenemethanol, and so on. The BTX can be effectively converted into harmless $CO_2$ and $H_2O$ at appropriate operating condition. Thus, the nontoxic recovery process was suggested as the removal method of BTX.

• Advances in Energy Research
• /
• v.8 no.4
• /
• pp.223-231
• /
• 2022

An ex-situ gravitational fixed bed pyrolysis reactor was used over Al₂O₃ supported Ni₂P based catalyst with various Ni/P molar ratios (0.5-2.0) and constant nickel loading of 5.37 mmol/g Al₂O₃ to determine the hydrodeoxygenation of rubberwood sawdust (RWS) at atmospheric pressure. The 3D catalysts formed were characterized structurally as well as acidic properties were determined by hydrogen-temperature programmed reduction (TPR). The Ni₂P phase formed completely on Al₂O₃ for 1.5 Ni/P ratio, although lesser crystallite sizes of Ni₂P were seen at Ni/P ratios less than 1.5. Additionally, it was shown that when nickel loading level increased, acidity increased and specific surface area dropped, probably because nickel phosphate is not easily converted to Ni₂P. When Ni/P ratio was 1.5, Ni₂P phase fully formed on Al₂O₃. The catalytic activity was explained in terms of impacts of reaction temperature and Ni/P molar ratio. At relatively high temperature of 450℃, the high-value deoxygenated produce was predominantly composed of n-alkanes. Based on the findings, it was suggested that hydrogenolysis, hydrodeoxygenation, dehydration, decarbonylation, and hydrogenation are all part of mechanism underlying hydrotreatment of RWS. In conclusion, the synthesized Ni₂P/ Al₂O₃ catalyst was capable of deoxygenating RWS with ease at atmospheric pressure, primarily resulting in long chained (C₉-C₂₄) hydrocarbons and acetic acid.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.4
• /
• pp.237-242
• /
• 2011

In this study, the catalytic activity of Mn-Phthalocyanine (Mn-PC) for VOCs (acetadehyde, propionaldehyde and toluene) combustion was determined. The reaction was carried out in a fixed bed reactor at the temperature range of $200{\sim}380^{\circ}C$. We investigated the physicochemical properties of Mn-PC before and after the pretreatment (air, $450^{\circ}C$, 1 hr, 60 cc/min) by TGA (Thermogravimetric Analyzer), BET (Brunauer Emmett Teller), EA (Elemental Analyzer), XRD (X-ray Diffractometer) and SEM (Scanning Electronic Microscope). By TGA analysis, 88 wt.% mass loss of Mn-PC was found at $419^{\circ}C$. The BET surface area of Mn-PC increased after the pretreatment. The decomposition and combustion of organic components in Mn-PC were observed by EA analysis. We also confirmed that Mn-PC had transformed into a new manganese oxide phase ($Mn_3O_4$) after the pretreatment by XRD analysis. By SEM analysis, many of the micropores generated during the pretreatment were found. The catalytic activity of Mn-PC with the pretreatment for propionaldehyde combustion was higher than that of $Mn_3O_4$ and fresh Mn-PC. It showed the catalytic activity of Mn-PC with the pretreatment for VOCs combustion by the order of toluene < acetadehyde < propionaldehyde.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.10
• /
• pp.1809-1816
• /
• 2000

The catalytic combustion of methanol as a model volatile organic compound(VOC) was been investigated over metal-phthalocyanine(PC) in a fixed bed flow reactor system. The catalytic activity of Co-PC pretreated with air and methanol mixture at $450^{\circ}C$ and 60 cc/min for 1 hr was very excellent. The order of catalytic activity on methanol combustion was summarized as follows: metal free-PC < Zn-PC < Fe-PC < Cu($\alpha$)-PC < Co-PC. By TG/DTA analysis, the tendency of thermal decomposition was increased as follows: metal free-PC < Zn-PC < Cu($\alpha$)-PC < Co-PC < Fe-PC. Under this pretreatment condition, the basic structures of Co-PC, Cu($\alpha$)-PC and Fe-PC were destroyed, and the new metal oxide such as $Co_3O_4$ from Co-PC was confirmed by EA and XRD analysis. But Zn-PC and metal free-PC were retained its basic structure under this pretreatment condition. On the combustion of methanol over Co-PC, HCHO and $HCOOCH_3$ were observed as an intermediate products in the high concentration of reactant or the short contact time(W/F).

• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.404-409
• /
• 2006

The catalytic combustion of toluene over Pd-Cu/USY zeolite has been examined by using FT-IR spectroscopy in a closed system under dry and humid conditions. The catalytic combustion of toluene (700 ppmv) in the temperature range of $80-220^{\circ}C$ has been investigated by using a fixed bed reactor. The Pd-Cu/USY catalyst showed the highest catalytic performance with respects to the PdO-CuO/USY and Pd/USY. Comparing to $PdO/Al_2O_3$ catalysts, the slight improvement in conversion was observed over PdO/USY catalysts under humid condition since USY zeolite is hydrophobic substrate and water give an additional oxygen source to zeolite surface like oxygen. The reduced catalysts showed more enhanced catalytic activity due to the reduced activation energy of combustion of toluene than oxidized catalysts such as PdO/USY and PdO-CuO/USY.

• Clean Technology
• /
• v.26 no.2
• /
• pp.145-150
• /
• 2020

Nitrous oxide (N₂O) is one of the six greenhouse gases, and it is essential to reduce N₂O by showing a global warming potential (GWP) equivalent to 310 times that of carbon dioxide (CO₂). Selective catalytic reduction (SCR) is a technology that converts ammonia into harmless N₂ and H₂O by using ammonia as a reducing agent to remove NOx, one of the air pollutants; the process also produces high denitrification efficiency. In this study, the Fe-BEA catalyst was steam-treated at 100 ℃ for 2 h before Fe ion exchange in the fixed bed reactor in order to investigate the effect of the steam-treated Fe-BEA catalyst on the NH₃-SCR reaction. NH₃-SCR reaction test of synthesized catalysts was performed at WHSV = 180 h^-1, 370 to 400 ℃ in the fixed bed reactor. The Fe-BEA(100) catalyst steam-treated at 100 ℃ showed a somewhat higher activity than the Fe-BEA catalyst at 370 to 390 ℃. The catalysts were characterized by BET, ICP, NH₃-TPD, H₂-TPR, and ²⁷Al MAS NMR in order to determine the cause affecting NH₃-SCR activity. The H₂-TPR result confirmed that the Fe-BEA(100) catalyst had a higher reduction of isolated Fe³⁺ than the Fe-BEA catalyst, and that the steam treatment increased the amount of isolated Fe³⁺ as an active species, thus increasing the activity.

• Korean Chemical Engineering Research
• /
• v.53 no.1
• /
• pp.121-126
• /
• 2015

The objective of this study is to evaluate the catalytic potential of the porous material prepared from water treatment sludge. The textural properties of the catalyst were studied using $N_2$ adsorption and desorption isotherms, scanning electron microscope, and X-ray diffraction. The pellet-type catalyst prepared using water treatment sludge is determined to be a material that contains mesopores as well as micropores. The specific surface area of the catalyst is $157m^2/g$. Acidic characteristics of the catalyst are analyzed by temperature-programmed desorption of ammonia and infrared spectroscopy of adsorbed pyridine. 2-Butanol dehydration reaction was carried out in a fixed bed catalytic reactor. Yields of 1-butene, trans-2-butene, and cis-2-butene at $350^{\circ}C$ were 25.6 wt%, 19.2 wt%, and 29.9 wt%, respectively. This catalytic activity of the catalyst based on water treatment sludge in 2-butanol dehydration is due to the acid sites composed of Bronsted acid sites and Lewis acid sites. It was confirmed that the catalyst based on water treatment sludge can be utilized to produce $C_4$ olefin through butanol dehydration.