• Elastomers and Composites
• /
• v.38 no.2
• /
• pp.167-174
• /
• 2003

Thermoplastic vulcanizates (TPV) or dynamic vulcanizates are thermoplastic elastomers produced by simultaneous mixing and crosslinking of a rubber and a thermoplastic. The objective of the present work is to investigate the effects of different types of peroxides as curing agents on the properties of PP/EPDM TPVs. The mechanical properties change significantly with the chemical nature of the peroxides and the extent of crosslinking at a fixed PP/EPDM blend ratio. The tensile strength of the TPVs obtained with the various peroxides can be related to the solubility parameters of the polymers and of the peroxides. The Young's modulus of the peroxide-cured TPVs can be correlated with the delta torque values of equivalent thermoset EPDM vulcanizates, corresponding to the crosslinking efficiencies of the peroxides.

• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.694-702
• /
• 2002

Activated carbons have been used as adsorbents in various industrial application, such as solvent recovery, gas separation, deodorization, and catalysts. In this study, the effects of residual water on the activated carbon adsorbent surface on the adsorption capacity of $CCl_4$ were investigated. Adsorption behavior in a fixed bed was studied in terms of feed concentration, flow rate, breakthrough curve and adsorption capacity for $CCl_4$. Desorption characteristics of residual water on activated carbon were also studied. The water contents of the activated carbon were varied in the range of 0-20%(w/w) and all experiments were performed at 298.15 K. The adsorption equilibrium data $CCl_4$ on the activated carbon were well expressed by Langmuir isotherm. The adsorption capacity of $CCl_4$ decreased with increasing residual water content. Desorption of residual water in activated carbon decreased expotentially with $CCl_4$ adsorption. The obtained breakthrough curves using LDF(linear driving force) model represented our experimental data.

• KSBB Journal
• /
• v.20 no.1 s.90
• /
• pp.26-33
• /
• 2005

The effects of carbon sources for exopolysaccharide production during batch cultivation of an Enterobacter sp. isolated from the composter were investigated. The highest amount of exopolysaccharide was obtained when lactose was used as carbon source. Lactose in medium was converted into glucose and galactose. Glucose was metabolized fast and was completely consumed, but about $20\%$ of lactose was accumulated as galactose. On the other hand, enzyme activity was about $350\~450$ unit with the increase of lactose concentration. Thus, it was considered that the exopolysaccharide might be produced in the course of that lactose was hydrolyzed into glucose and galactose by $\beta-galactosidase$ with respect to that enzyme activity on lactose hydrolysis was accorded to the exopolysaccharide production. When glucose and galactose were added to lactose medium, respectively, it could be considered that glucose was as a repressor and galactose was as a inducer for $\beta-galactosidase$ synthesis even though the mechanisms were not elucidated. The increase of lactose concentration was almost ineffective to the specific growth rate $(0.133\~0.151\;hr^[-1})$ but showed the difference in the biomass content. The higher carbon source concentration, the more residual sugar remained. It was assumed that the optimum lactose concentration for exopolysaccharide production was $30\~70g/L.$ On the other hand, it was considered that the nitrogen acted as growth limiting nutrients to the cell growth. In the cases of 30 and 70 g/L of the fixed carbon concentrations, the increase of the nitrogen sources concentration caused a remarkable increase within the range of $0.059\~0.225\;hr^{-1}$ and $0.141\~0.237hr^{-1}$ of the specific growth rate, respectively, while there was no significant difference in biomass.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.4
• /
• pp.405-413
• /
• 2013

The char oxidation characteristics of high ash coal were experimentally investigated at several temperatures (from 900 to $1300^{\circ}C$) for 4 types of coals (Gunvor, Glencore, Noble, and ECM) under atmospheric pressure in a drop tube furnace (DTF). The char reaction rate was calculated from the exhaust gas concentrations (CO and $CO_2$) using FT-IR, and the particle temperature was measured using the two-color method. In addition, the activation energy and pre-exponential factor for high ash coal char were calculated based on the Arrhenius equation. The results show that as the ash content increases, the particle temperature and area reactivity decreases. This is because in high ash coal, the large heat capacity of the ash, ash vaporization, and relatively low fixed carbon content of ash suppress combustibility during char oxidation. As a result, the higher ash content of coal leads to high activation energy.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.375-378
• /
• 2014

In this study, we carried out torrefaction experiment using PKS(Palm Kernel Shell), and Bagasse as a raw material of oversee of herbaceous biomass and using waste wood and logging residue as a raw material of domestic of woody biomass. And then, by analyzing the physical & chemical properties, we investigated the characteristics as a fuel. By using the result of thermo gravimetric analysis, the biomass residue was torrefied for 30 minutes at a temperature range of $250-350^{\circ}C$ in anaerobic condition. As a result, torrefied materials of moisture content are lower than raw, but of fixed carbon, calorific value and ash are higher than raw.

• New & Renewable Energy
• /
• v.4 no.4
• /
• pp.37-43
• /
• 2008

Three properties of food waste are water 80%, ash 3%, volatile matter 17%. When food waste goes through treatment process such as removal of foreign substances, removal of water as well as sodium, dryness, and pulverization, it transforms into 4,000 Kcal/kg purverized fuel if moisture content is below 13%. Fuel ratio (fixed carbon/volatile matter) of purverized fuel is low compared with bituminuous coal. Ignition temperature measured by thermogravimetry analyzer is about $460^{\circ}C$. Combustion test of purverized fuel have been performed using energy recovery facility which include storage tank of dewatered cake, dryer, hammer mill, combuster including burner, boiler, flue gas treatment equipment. When 160-180 kg/hr of fuel is steadily supplied to burner for 3 hours, combustor temperature reaches about $1000^{\circ}C$ and CO is 77-103 ppm at 1.55 excess air ratio and SOx and Cl are under 2 ppm and 1ppm, respectively. This experiment demonstrate that purverized fuel made from food waste could be an alternative clean energy at the age of high oil price.

• Journal of ILASS-Korea
• /
• v.21 no.1
• /
• pp.29-36
• /
• 2016

The effect of high ambient temperature and pressure conditions on the combustion performance of n-butanol, n-heptane and its mixing fuel (BH 20) were studied in this work. To reveal this, the closed homogeneous reactor model applied and 1000-1200 K of the initial temperature, 20-30 atm of initial pressure and 1.0 of equivalence ratio were set to numerical analysis. It was found that the results of combustion temperature was increased and the ignition delay was decreased when the ambient conditions were elevated since the combustion reactivity increased at the high ambient conditions. On the contrary, under the low combustion temperature condition, the combustion pressure was more influenced by the ambient temperature in the same ambient conditions. In addition, the total mass and the mass density of tested fuels were influenced by the ambient pressure and temperature. Also, soot generation of mixing fuel was decreased than n-heptane fuel due to the oxygen content of n-butanol fuel.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.149-152
• /
• 2008

Three properties of food waste are water 80%, ash 3%, volatile matter 17%. When food waste goes through treatment process such as removal of foreign substances, removal of water as well as sodium, dryness, and pulverization, it transforms into 4,000Kcal/kg purverized fuel if moisture content is below 13%. Fuel ratio(fixed carbon/volatile matter) of purverized fuel is low compared with bituminuous coal. Ignition temperature measured by thermogravimetry analyzer is about $460^{\circ}C$. Combustion test of purverized fuel have been performed using energy recovery facility which include storage tank of dewatered cake, dryer, hammer mill, combuster including burner, boiler, flue gas treatment equipment. When 160-180 kg/hr of fuel is steadily supplied to burner for 3 hours, combueter temperature reaches about $1000^{\circ}C$ and CO is 77-103ppm at 1.55 excess air ratio and SOx and Cl are under 2ppm and 1ppm, respectively. This experiment demonstrate that purverized fuel made from food waste could be an alternative clean energy for high oil price era

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.5
• /
• pp.819-825
• /
• 2000

The physico-chemical characteristics and the combustion activities of a waste automotive catalyst were carried out in this study. The physico-chemical characteristics of waste automotive catalyst was examined by EA(Elemental analysis), ICP-AES (Inductively coupled plasma-atomic emission spectrophotometer), and XRD(X-ray diffraction) analysis. Carbon deposit amount was higher in front brick than rear brick of catalyst, and increased with mileage. The content of Pt. Pd and Rh in waste automotive catalyst was different from the car manufacturing company. The combustion activities of waste automotive catalyst were investigated for acetaldehyde as a model VOC in a fixed bed reactor at atmospheric pressure. The catalytic activity of rear brick for acetaldehyde combustion was better than front brick of waste automotive catalyst. The catalytic activity of waste automotive catalyst for acetaldehyde combustion decreased with mileage. The linear relationship between catalytic activity and mileage was negative and has a very excellent correlation. Finally, the waste automotive catalyst has a good catalytic activity for acetaldehyde combustion. and can be used to control of small emission source.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.2
• /
• pp.70-77
• /
• 1999

Objective of this research is to obtain fundamental data of carbonized wood wastes for soil condition, de-ordorization, absorption of water, carrier for microbial activity, and purifying agent for water quality of river. The carbonization technique and the properties of carbonized wood wastes(thinned trees) are analyzed. Proximate analysis shows the thinned wood contains 0.22-0.73% ash, 77-80% volatile matter, and 10-14% fixed carbon. The charcoal yield decreases and the shrinkage rate increases as the carbonization temperature and time increase. The charcoal yields of Larix leptolepis, Pinus rigida and Pinus densiflora are high, whereas those of Pinus koraiensis and Quercus variabilis are low. The shrinkage rate by carbonization has same trend as water removal of wood. The specific gravity after the carbonization decreases about 50% comparing to green wood. The charcoal has 0.89-4.08% ash, 6.31-13.79% volatile matter, and 73.9-83.5% fixed carbon. As the carbonization temperature and time increase, pH of charcoal increases. When the carbonization temperature is $400^{\circ}C$, pH is about 7.5. When the temperature is between 600 to $800^{\circ}C$, pH is about 10 with small difference. The water-retention capacity is not affected by the carbonization temperature and time. The water-retention capacity within 24hr is about 2.5 - 3times of sample weight, and the equivalent moisture content becomes 2-10% after 24 hr.