• The Journal of Advanced Prosthodontics
• /
• v.8 no.1
• /
• pp.30-36
• /
• 2016

PURPOSE. The aim of this study was to evaluate the fracture resistance and fracture behavior of monolithic zirconia crowns in accordance with the preparation design and aging simulation method. MATERIALS AND METHODS. An upper first molar was prepared sequentially with three different preparation designs: shoulderless preparation, 0.4 mm chamfer and 0.8 mm chamfer preparation. For each preparation design, 30 monolithic zirconia crowns were fabricated. After cementation on Cr-Co alloy dies, the following artificial aging procedures were performed: (1) thermal cycling and mechanical loading (TCML): 5000 cycles of thermal cycling $5^{\circ}C-55^{\circ}C$ and chewing simulation (1,200,000 cycles, 50 N); (2) Low Temperature Degradation simulation (LTD): autoclave treatment at $137^{\circ}C$, 2 bar for 3 hours and chewing simulation; and (3) no pre-treatment (control group). After artificial aging, the crowns were loaded until fracture. RESULTS. The mean values of fracture resistance varied between 3414 N (LTD; 0.8 mm chamfer preparation) and 5712 N (control group; shoulderless preparation). Two-way ANOVA analysis showed a significantly higher fracture loads for the shoulderless preparation, whereas no difference was found between the chamfer preparations. In contrast to TCML, after LTD simulation the fracture strength of monolithic zirconia crowns decreased significantly. CONCLUSION. The monolithic crowns tested in this study showed generally high fracture load values. Preparation design and LTD simulation had a significant influence on the fracture strength of monolithic zirconia crowns.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.6
• /
• pp.431-436
• /
• 2015

PURPOSE. The aim of this study was to evaluate occlusal contacts generated by 3 different biogeneric design modes (individual (BI), copy (BC), reference (BR)) of CEREC software and to assess the designs subjectively. MATERIALS AND METHODS. Ten pairs of maxillary and mandibular casts were obtained from full dentate individuals. Gypsum cast contacts were quantified with articulating paper and digital impressions were taken. Then, all ceramic crown preparation was performed on the left first molar teeth and digital impressions of prepared teeth were made. BI, BC, and BR crowns were designed. Occlusal images of designs including occlusal contacts were superimposed on the gypsum cast images and corresponding contacts were determined. Three designs were evaluated by the students. RESULTS. The results of the study revealed that there was significant difference among the number of contacts of gypsum cast and digital models (P<.05). The comparison of the percentage of virtual contacts of three crown designs which were identical to the contacts of original gypsum cast revealed that BI and BR designs showed significantly higher percentages of identical contacts compared with BC design (P<.05). Subjective assessment revealed that students generally found BI designs and BR designs natural regarding naturalness of fissure morphology and cusp shape and cusp tip position. For general occlusal morphology, student groups generally found BI design "too strong" or "perfect", BC design "too weak", and BR design "perfect". CONCLUSION. On a prepared tooth, three different biogeneric design modes of a CAD/CAM software reveals different crown designs regarding occlusal contacts and morphology.

• Journal of Technologic Dentistry
• /
• v.42 no.1
• /
• pp.9-16
• /
• 2020

Purpose: The purpose of this study was to compare the marginal and internal fit of lithium disilicate ceramic inlay produced by heat pressing that inlay pattern made by subtractive manufacturing and additive manufacturing method. Methods: A mandibular lower first molar that mesial occlusal cavity (MO cavity) die was prepared. After fabricating an epoxy resin model using a silicone impression material, epoxy resin die was scanned with a dental model scanner to design an MO cavity inlay. The designed STL pile was used to fabricate wax patterns and resin patterns, and then lithium disilicate ceramic inlays were fabricated using hot-press method. For the measurement of the marginal and internal gap of the lithium disilicate, silicone replica method was applied, and gap was measured through an optical microscope (x 80). Data were tested for significant differences using the Mann-Whitney Utest. Results: The marginal fit was 103.56±9.92㎛ in the MIL-IN group and 81.57±9.33㎛ in the SLA-IN group, with a significant difference found between the two groups (p<0.05). The internal fit was 120.99±17.52㎛ in the MIL-IN group and 99.18±6.65㎛ in the SLA-IN group, with a significant difference found between the two groups (p<0.05). Conclusion: It is clinically more appropriate to apply the additive manufacturing than subtractive manufacturing method in producing lithium disilicate inlay using CAD/CAM system.

• Journal of the Korean Ceramic Society
• /
• v.52 no.2
• /
• pp.140-145
• /
• 2015

In this study, we verified the relationship among the electrical conductivity, chemical durability, and structure of conductive vanadate glass in which $BO_3$ and $BO_4$ and $V^{4+}$ and $V^{5+}$ coexist simultaneously. We prepared samples of vanadium borophosphate glass with various compositions, given by $50V_2O_5-xB_2O_3-(50-x)P_2O_5$(x = 0 ~ 20 mol%) and $70V_2O_5-xB_2O_3-(70-x)P_2O_5$(x = 0 ~ 10 mol%), and analyzed the electrical conductivity, chemical durability, FT-IR spectroscopy, thermal properties, density, and molar volume. Substituting $B_2O_3$ for $P_2O_5$ was found to improve the electrical conductivity, chemical durability, and thermal properties. From these results, we can draw the following conclusions. First, the electrons shift from the electron rich $V^{4+}$ to the electron deficient $BO_3$ as the $B_2O_3$ content increases. Second, the improvement in chemical durability and thermal properties is attributed to an increase in cross-linked structures by changing from a $BO_3$ structure to a $BO_4$ structure.

• The Journal of Korean Academy of Prosthodontics
• /
• v.30 no.3
• /
• pp.379-400
• /
• 1992

The purpose of this study was to analyze the magnitude and distribution of stress using a photoelastic model from the mandibular distal extension removable partial dentures with the mesial or distal placement of the occlusal rest and the mesial or distal connection in the back-action clasp with the five various designs of the back-action clasp, that is, the mesial connection and the distal rest, the distal connection and mesial rest, the mesial connection and mesial rest, the distal connection and the mesial and distal rest, and the mesial connection, and the mesial and distal rest. A photoelastic model was made of the epoxy resin(PC-1) and the hardner(PLH-1) with the acrylic resin teeth used and was coated with the plastic cement-1 at the lingual surface of the model and then five kinds of the removable partial dentures on the photoelastic model were set. A unilateral vertical load of 12.5 kg was applied on the central fossa of the first molar with the use of specially designed loading device and the pattern and distribution of the stress of the photoelastic model under each condition was analyzed by the reflective circular polariscope. The following results were obtained. 1. In the back-action clasp with the mesial connection and mesial rest of the case 3, the effect of the stress distribution was the most favorable. 2. In the back-action clasp with the mesial and distal rest, of the case 4 and 5, the stress distribution was more greatly showed in the terminal abutment. 3. Generally, the stress distribution was more favarable in the mesial connection than in the distal connection. 4. In the back-action clasp with the mesial connection of the case 1, 3 and 5, the stress distribution was the most favorable in the mesial rest.

• Journal of Dental Anesthesia and Pain Medicine
• /
• v.18 no.3
• /
• pp.151-159
• /
• 2018

Background: The pain involved in orthodontic treatments may involve inflammatory processes. This study evaluated the effect of using a naproxen patch for pain reduction in the separating stage of fixed orthodontic treatment. Methods: In this double-blind, randomized, controlled clinical trial of 35 orthodontic patients (age: 14-19 years) who had pain during separator placement, each patient randomly placed naproxen and placebo patches in the first permanent molar region, in opposite quadrants of the same jaw. Patches were replaced every 8 hours until 3 days after separator placement. Patients recorded their pain perception at 2, 6, and 24 hours, and on days 2 (6 PM), 3 (10 AM and 6 PM), and 7 (10 AM and 6 PM), using a visual analog scale. Mean pain scores were compared for the two patches, and effects of sex and age thereon determined. Results: Data from 29 patients (21 girls, eight boys) were analyzed. Mean pain values decreased over time for both patches (P < 0.001). Recorded pain did not differ significantly between the sexes (P = 0.059) or between those aged <16 and those ${\geq}16years$ (P = 0.106). Mean pain recorded with naproxen patches was statistically significantly less than that with placebo patches at all time points (P = 0.004). Conclusion: The naproxen patch was more efficient than the placebo patch for reducing pain at all time points. The highest pain score was recorded at 6 hours, and the least pain was recorded at the $7^{th}$ day after separator placement.

• Restorative Dentistry and Endodontics
• /
• v.40 no.3
• /
• pp.209-215
• /
• 2015

Objectives: The aim of this study was to evaluate the fluoride release of conventional glass ionomer cements (GICs) and resin-modified GICs. Materials and Methods: The cements were grouped as follows: G1 (Vidrion R, SS White), G2 (Vitro Fil, DFL), G3 (Vitro Molar, DFL), G4 (Bioglass R, Biodinamica), and G5 (Ketac Fil, 3M ESPE), as conventional GICs, and G6 (Vitremer, 3M ESPE), G7 (Vitro Fil LC, DFL), and G8 (Resiglass, Biodinamica) as resin-modified GICs. Six specimens (8.60 mm in diameter; 1.65 mm in thickness) of each material were prepared using a stainless steel mold. The specimens were immersed in a demineralizing solution (pH 4.3) for 6 hr and a remineralizing solution (pH 7.0) for 18 hr a day. The fluoride ions were measured for 15 days. Analysis of variance (ANOVA) and Tukey's test with 5% significance were applied. Results: The highest amounts of fluoride release were found during the first 24 hr for all cements, decreasing abruptly on day 2, and reaching gradually decreasing levels on day 7. Based on these results, the decreasing scale of fluoride release was as follows: G2 > G3 > G8 = G4 = G7 > G6 = G1 > G5 (p < 0.05). Conclusions: There were wide variations among the materials in terms of the cumulative amount of fluoride ion released, and the amount of fluoride release could not be attributed to the category of cement, that is, conventional GICs or resin-modified GICs.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.41-47
• /
• 2005

The transesterification of dimethyl terephthalate (DMT) with 1,3-propanediol (PDO) was investigated in the presence of catalyst, titanium (IV) butoxide (TBO), at 175~190 $^{\circ}C$ . The degree of transesterification reaction was measured by the output of methanol which was distilled from the reactor. The amount of methanol increased as the reaction temperature, molar ratio and catalyst concentration increased. The observed overall rate of the transesterification was third order; first order with respect to DMT, PDO, and the concentration of catalyst, respectively. Using calculated rate constants, the activation energy for transesterification was 26.93 kcal/mole. The melting temperature of bis(2-hydroxytrimethyl) terephthalate (BHTMT) was 85.2$^{\circ}C$ and heat of fusion 141.3 J/g.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.700-711
• /
• 2018

CdS synthesized by the chemical bath method at $70^{\circ}C$, has been used as an electron transport layer in the planar structure of the perovskite solar cells. A two-step spin process produced a mixed halide perovskite of $CH_3NH_3PbI_{3-x}Cl_x$ and a mixture of $PbCl_2$ and $PbI_2$ was deposited on CdS, followed by a sub-sequential reaction with MAI ($CH_3NH_3I$). The added $PbCl_2$ to $PbI_2$ in the first spin-step affected the structure, orientation, and shape of lead halides, which varied depending on the content of Cl. A small amount of Cl enhanced the surface morphology and the preferred orientation of $PbI_2$, which led to large and uniform grains of perovskite thin films. In contrast, the high content of Cl produces a new phase PbICl in addition to $PbI_2$, which leads to the small and highly uniform grains of perovskites. An improved surface coverage of perovskite films with the large and uniform grains maximized the performance of perovskite solar cells at 0.1 molar ratio of $PbCl_2$ to $PbI_2$. The depth profiling of elements in both lead halide films and mixed halide perovskite films were measured by Rutherford backscattering spectroscopy, revealing the distribution of chlorine along with the thickness, and providing the basis for the mechanism for enhanced preferred orientation of lead halide and the microstructure of perovskites.

• The korean journal of orthodontics
• /
• v.49 no.6
• /
• pp.393-403
• /
• 2019

Objective: Sliding mechanics using orthodontic miniscrews is widely used to stabilize the anchorage during extraction space closure. However, previous studies have reported that both posterior segment displacement and anterior segment displacement are possible, depending on the mechanical properties of the archwire. The present study aimed to investigate the effect of archwire stiffness and friction change on the displacement pattern of the maxillary posterior segment during anterior segment retraction with orthodontic miniscrews in sliding mechanics. Methods: A three-dimensional finite element model was constructed. The retraction point was set at the archwire level between the lateral incisor and canine, and the orthodontic miniscrew was located at a height of 8 mm from the archwire between the second premolar and first molar. Archwire stiffness was simulated with rectangular stainless steel wires and a rigid body was used as a control. Various friction levels were set for the surface contact model. Displacement patterns for the posterior and anterior segments were compared between the conditions. Results: Both the anterior and posterior segments exhibited backward rotation, regardless of archwire stiffness or friction. Among the conditions tested in this study, the least undesirable rotation was found with low archwire stiffness and low friction. Conclusions: Posterior segment displacement may be unavoidable but reducing the stiffness and friction of the main archwire may minimize unwanted rotations during extraction space closure.