• Journal of Environmental Science International
• /
• v.12 no.2
• /
• pp.217-225
• /
• 2003

Samples of size-fractionated PM10 (airborne particulate matter with aerodynamic diameter less than $10\mu\textrm{m}$) were collected at an urban site in Jeju city from May to September 2002. The mass concentration and chemical composition of the samples were measured. The data sets were then applied to the CMB receptor model to estimate the source contribution of PM10 in Jeju area. The average PM10 mass concentration was 28.80$\mu\textrm{g}/m^3$ ($24.6~33.49\mu\textrm{g}/m^3$), and the FP (fine particle with aerodynamic diameter less than $2.l\mu\textrm{m}$ fraction in PM10 was approximately 8% higher than the CP (coarse particle with aerodynamic diameter greater than $2.l\mu\textrm{m}$ and less than $10\mu\textrm{m}$ fraction in PM10. The CP composition was obviously different from the FP composition, that is, the most abundant water soluble species was nitrate ion in the FP, but sulfate ion in the CP. Also sulfur was the most dominant element in the FP, however, sodium was that in the CP. From CMB receptor model results, it was found that road dust was the largest contributor to the CP mass concentration (45% of the CP) and ammonium nitrate, domestic boiler, and marine aerosol were major sources to the CP mass. However, the secondary aerosol was the most significant contributor to the FP mass concentration (45% of the FP). In this study, it was suggested that the contributions of soil dust and gasoline vehicle became very low due to collinearity with road dust and diesel vehicle, respectively.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.2
• /
• pp.224-229
• /
• 2010

This study was conducted to reclassify Cheongpung series based on the second edition of Soil Taxonomy, and to dicuss the formation of Cheongpung series distributed on the diluvial terrace. Morphological properties of typifying pedon of Cheongpung series were investigated, and physico-chemical properties were analyzed according to Soil survey laboratory methods manual. The typifying pedon of Cheongpung series has red (2.5YR 4/6) silty clay loam Ap horizon (0-18 cm), red (2.5YR 4/8) clay BAt horizon (18-35 cm), red (2.5YR 4/2) cobbly clay Bt1 horizon (35-65 cm), and red (2.5YR4/6) cobbly clay Bt2 horizon (more than 65 cm). The typifying pedon has an argillic horizon from adepth of 18 to more than 65 cm, and a base saturation (sum of cations) of less than 35% at 125 cm below the upper boundary of the argillic horizon. It can be classified as Ultisol, not as Alfisol. It has udic soil moisture regime, and can be classified as Udult. Also that meets the requirements of Typic Hapludults. It has 35% or more clay at the particle-size control section, and have mesic soil temperature regime. Therefore Cheongpung series can be classified as fine, mesic family of Typic Hapludults, not as fine, mesic family of Ultic Hapludalfs. Cheongpung series occur on moderately elevated diluvial terrace which have relatively stable geomorphic surface. They are developed as Ultisols with clay mineral weathering, translocation of clays to accumulate in an argillic horizon, and leaching of base-forming cations from the profile for relatively long periods under humid, and temperate climates in Korea.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.6
• /
• pp.1258-1263
• /
• 2011

This study was conducted to reclassify Asan series based on the second edition of Soil Taxonomy and to discuss the formation of Asan series distributed on the rolling to hilly areas. Morphological properties of typifying pedon of Asan series were investigated and physico-chemical properties were analyzed according to Soil survey laboratory methods manual. The typifying pedon of Asan series has dark yellowish brown (10YR 4/4) gravelly loam Ap horizon (0-18 cm), strong brown (7.5YR 5/6) gravelly clay loam BA horizon (18-30 cm), red (2.5YR 4/6) gravelly clay loam Bt1 horizon (30-52 cm), red (2.5YR 4/8) gravelly clay loam Bt2 horizon (52-98 cm), and red (2.5YR 4/8) gravelly clay loam C horizon (98-160 cm). The typifying pedon has an argillic horizon from a depth of 30 to 98 cm and a base saturation (sum of cations) of less than 35% at 125 cm below the upper boundary of the argillic horizon. It can be classified as Ultisol, not as Inceptisol. It has udic soil moisture regime, and can be classified as Udult. Also that meets the requirements of Typic Hapludults. It has 18-35% clay at the particle-size control section, and has mesic soil temperature regime. Therefore Asan series can be classified as fine loamy, mesic family of Typic Hapludults, not as fine loamy, mesic family of Typic Dystrudepts. Asan series occur on rolling to hilly areas in residual materials derived from granite gneiss, schist, and gneiss rocks. They are developed as Ultisols with clay mineral weathering, translocation of clays to accumulate in an argillic horizon, and leaching of base-forming cations from the profile for relatively long periods under humid and temperate climates in Korea.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.5
• /
• pp.330-335
• /
• 2009

This study was conducted to reclassify Jangho series based on the second edition of Soil Taxonomy : A Basic System of Soil Classification for Making and Interpreting Soil Surveys. Morphological properties of typifying pedon of Jangho series were investigated and physico-chemical properties were analyzed according to Soil Survey Laboratory Methods Manual. The typifying pedon of Jangho series has very dark grayish brown (10YR 3/2) gravelly silt loam A horizon (0~14 cm), very dark brown (7.5YR 3/2) silty clay BAt horizon (14~31 cm), dark brown (7.5YR 3/4) silty clay Bt1 horizon (31~58 cm), brown (7.5YR 4/4) silty clay Bt2 horizon (58~90 cm), and brown (7.5YR 4/4) clay Bt3 (90~120 cm) horizon. That is developed on river terraces. The typifying pedon has an argillic horizon from a depth of 14 to more than 120 cm and a base saturation (sum of cations) of less than 35% at 125 cm below the upper boundary of the argillic horizon. That can be classified as Ultisol. The typifying pedon has 0.9 % or more organic carbon in the upper 15 cm of the argillic horizon, and can be classified as Humult, which is reported for the first time in Korea. That does not have fragipan, kandic horizon, sombric horizon, plinthite, etc. in the given depths, and keys out as Haplohumult. Also that meets the requirements of Typic Haplohumult. That has 35 % or more clay at the particle-size control section, and has mesic soil temperature regime. Jangho series can be classified as fine, mixed, mesic family of Typic Haplohumults, not as fine silty over clayey, mixed, mesic family of Mollic Hapludalfs.

• Korean Journal of Soil Science and Fertilizer
• /
• v.22 no.3
• /
• pp.163-172
• /
• 1989

In order to study spatial variability of soil physical properties accross the land-partitioned boundary on Hwadong silt clay loam soil (Fine clayey, mixed, mesic family of Aquic Hapludalfs), all measured data were analyzed by means of kriging, fractile diagram, smooth frequency distribution, and autocorrelation. Sampling for soil particle size distribution analysis was made at 225 intersections of $15{\times}15$ grid with 10m interval. Field capacity, bulk density and saturated hydraulic conductivity were measured in situ at 594 intersections of $33{\times}18$ grid with 2.5m interval in only $6,000m^2$ reselected from $22,500m^2$ of sampling area for particle size distribution analysis. Sampled or measured soil depths were 0 to 10cm 25 to 35cm and 50 to 60cm at each intersections. The results are summarized as follows: 1. The coefficient of variance (CV) of various physical properties ranges from 4.8 to 128.8%. Saturated hydraulic conductivity is classified into the high variation group with CV greater than 100%, while the low variation group with CV smaller than 10% consists of bulk density. Other properties belong to the medium variation group with CV between 10 and 100%. 2. The appropriate number of soil samples for the determination of various physical properties with error smaller than 10% are calculated as one for bulk density, six for field moisture capacity, 16 for silt, 19 for clay, 69 for sand and 686 for saturated hydraulic conductivity. 3. Smooth frequency distribution and fractile diagram show that saturated hydraulic conductivity is in lognormal distribution while other physical properties are in normal distribution. 4. Serial correlation analysis reveals that the soil physical properties have spatial dependence between two nearest neighbouring grid points. Autocorrelation analysis of physical properties measured between the serial grid points in the direction of south to north following section boundary shows that the zone of influence showing stationarity ranges from 7.5 to 40m. In the direction of east to west across section boundary, the autocorrelogram of many physical properties shows peaks with the periodic interval of 30m, which are similar to the partitioned land width. This reveals that the land-partitioned boundary causes soil variability.

• Journal of Soil and Groundwater Environment
• /
• v.7 no.2
• /
• pp.35-44
• /
• 2002

In order to determine the contamination of the aromatic hydrocarbons in soil, a fiber-optic sensing technique with fluorescence detector has been proposed. Previous researches have shown that the optimal condition for detecting benzene, toluene, ethylbenzene, xylene (BTEX) was 260 nm /290 nm (excitation/emission wavelength). However, broader fluorescence spectra of BTEX-polluted soil sample ranging from 300 nm to 600 nm were observed. Additionally, the intensity of fluorescence increased with increasing BTEX concentration, which was conspicuous in the fine-particle soil, The overall results indicated that the suggested technique could be useful for in-situ monitoring system for subsurface oil-storage tank.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.1
• /
• pp.1-7
• /
• 2010

This study was carried out to investigate plow pan characteristics and to grasp the relationship between its particle size distribution fractal dimension ($D_m$) and water transport in paddy plow pan. Twenty four soil sampling sites with different management groups, ordinary and sandy-textured, were selected and investigated for physical properties of soils such as Yamanaka hardness in April, non-submerged condition, before rice seedling transplanting. The plow pan appearing depth and thickness was determined by penetration resistance profile. Undisturbed core samples with five replicates were sampled at plow pan layerwith 2 inch cores for measuring soil bulk density and saturated hydraulic conductivity. The particle size distribution fractal dimension ($D_m$) was calculated by the method following the procedure Tylerand Wheacraft (1992), using the USDA-based particle size analysis datawith fractions of 0-0.002, 0.002-0.053, 0.053-0.1, 0.1-0.25, 0.25-0.5, 0.5-1.0, and 1.0-2.0 mm. The plow pan of investigated fields appeared at a range from 5 to 30 cm depth, showing minimum value in sandy-textured management group and maximum value in ordinary management group. The thickness of plow pan were distributed from 5 to 17 cm, showing both minimum and maximum values in sandy-textured management group. Averagely, the plow appearing depth were deeper in ordinary management group than in sandy-textured management group, whereas the reverse in the thickness of plow pan. The particle size distribution fractal dimension ($D_m$) had higher value with finer textures, with higher fractality in coarser texture. Saturated hydraulic conductivities, $K_s$, of plow pan soils distributed from 0.5 to 1420 mm $day^{-1}$, having the highest value in sandy skeletal soils. The $K_s$ decreased with decreasing clay content and $D_m$, showing power function relationships. The coefficient of determination, $R^2$, of the fitted power functions were higher in $D_m$ as x-axis than in clay content. This means that $D_m$ could give us more effective estimation than clay content. Especially, sandy-textured paddy soils had higher $R^2$, compared to ordinary paddy soils. $K_s$ of relatively coarse-textured soils with less than 18%of clay content, therefore, was more dependent on particle size distribution than that of relatively fine-textured soils. From these results, it could be concluded that the fractal scaling gives us a unique quantity describing particle size distribution and then can be applied to estimate saturated hydraulic conductivity, especially more effective in coarse-textured soils.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.5
• /
• pp.477-485
• /
• 2000

The data set was collected on fifty-eight different days with a 24-h sampling period from October 27, 1995 through August 25, 1996. From the chemical mass balance (CMB) analysis of $PM_{2.5}$ in the Chongju area, the contributions from soil, gasoline, diesel, light and heavy oil combustion were 2.6%, 15.4%, 9.0%, 28.8% and 1.5%, respectively. Residual $NO_{3}^{-}$), residual $SO_{4}^{2-}$ and residual OC, possibly formed in the atmosphere. represented additional 8.0, 10.2, and 1.6% of the $PM_{2.5}$, respectively. Other unidentified sources constituted the remaining 22.9%. From the CMB analysis, the $PM_{2.5}$ source contribution for fall, winter, spring and summer were 92, 76.8, 77.5 and 59.2%, respectively.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2001.11a
• /
• pp.185-186
• /
• 2001

미세입자의 배출원을 추정하기 위해서는 수용지점에 영향을 미칠 수 있는 배출원의 화학적 특성에 관한 정보를 필요로 한다. 수용모델(chemical mass balance model, CMB)의 경우, 모델수행에 필요한 정보는 각각의 배출원에서 배출되는 입자의 화학적 구성성분특성을 파악하는 것이 가장 중요하다(Waton et al., 1984; U. S. EPA, 1987; 강병욱 등, 2000) 이러한 배출원으로는 각종 산업배출원, 자동차, 토양, 도로 비산먼지 등 지역의 특성에 따라서 다양한 배출원들이 대상이 될 수 있다. (중략)

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.6
• /
• pp.478-485
• /
• 2009

This study was conducted to reclassify Yongheung series based on the second edition of Soil Taxonomy and to discuss the formation of Yongheung series in Jeju Island. Morphological properties of typifying pedon of Yongheung series were investigated and physico-chemical properties were analyzed according to Soil Survey Laboratory Methods Manual. The typifying pedon contains 3.2~3.4% oxalate extractable (Al + 1/2 Fe), less than 85% phosphate retention, and higher bulk density than $0.90Mg\;m^{-3}$. That can not be classified as Andisol. But it has an argillic horizon from a depth of 15 to 150 cm and a base saturation (sum of cations) of less than 35% at 125 cm below the upper boundary of the argillic horizon. That can be classified as Ultisol, not as Andisol or Alfisol. The typifying pedon has 0.9 % or more organic carbon in the upper 15 cm of the argillic horizon and accordingly, can be classified as Humult. It has a clay distribution in which the percentage of clay does not decrese from its maximum amount by 20% or more within a depth of 150 cm from the mineral soil surface, and keys out as Palehumult. Also that meets the requirements of Typic Palehumult. That has 35 % or more clay at the particle-size control section and has mesic soil temperature regime. Yongheung series can be classified as fine, mixed, thermic family of Typic Palehumults, not as fine, mixed, thermic family of Typic Hapludalfs. Most soils distributed in the southern coastal areas in Jeju island which have a humid climate are developed as Andisols. But Yongheung series distributed in this areas and derived from mainly trachyte, trachytic andesite, and volcanic ash are developed as Ultisols.