• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.3
• /
• pp.69-75
• /
• 2001

Photoimageable thick film technology is a new technology in that the lithography process such as exposure and development is applied to the conventional thick film process. Line resolution of 25 $\mu\textrm{m}$ width and 25 $\mu\textrm{m}$ space could be obtained by laminating green sheet, printing photoimageable Ag paste, exposing the test patterns, developing, and co-firing. In case of using the alumina substrate, 20 $\mu\textrm{m}$ fine line could be also obtained by similar process. Test results showed that exposing power density and developing time were the most important processing parameters for the fine line formation. Microstrip and series gap resonators with well-defined line morphology and good transmission characteristics in high frequency were formed by this new technology, and thereby dielectric constant and loss of test substrate were calculated.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.1
• /
• pp.19-31
• /
• 1999

One of the non-photorealistic rendering method, a drawing technique which uses only fine curves and dashed line, is widely employed in an knots and post stamps printing. Engraving of the curves and lines are traditionally performed by human engravers which leads to low productivity in printing preparation. As an effort to improve productivity and quality, a drawing automation method which can easily produce a portrait composed of vector data for laser or chemical engraving is proposed. The method shows that it is possible to draw a portrait by controling the width and length of predefined fine lines according to the gray scales a the end points of each fine lines. A gradually controled weighting factor method is proposed in addition to the author previous works to prevent undesirable boundaries in an identical texture region. User interface functions of a commercial CAD system are heavily employed to exploit the presented method.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.210.1-210.1
• /
• 2005

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.669-670
• /
• 2011

• Current Photovoltaic Research
• /
• v.9 no.4
• /
• pp.123-127
• /
• 2021

This study was on electrode design for the realization of a solar cell that combines electrode formation and module integration process to overcome printing limitations. We used the passivated emitter rear contact (PERC) solar cell. Wafer size was 156.75 mm ×156.75 mm. The fabricated cell results showed that the open-circuit voltage of 649 mV, short-circuit current density of 36.15 mA/cm², fill factor of 68.5%, and efficiency of 16.06% with electrode conditions the 24BBs with the width 190 ㎛ and 90FBs with the width 45 ㎛. For improving efficiency, the characteristics of the solar cell were checked according to the change in the number of BBs and FBs and the change in line fine width. It is confirmed that the efficiency of the solar cell will be improved by increasing the number of FBs from 90 to 120, and increasing the line width of the FBs by about 10 ㎛ compared to the manufacturing solar cells.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.4
• /
• pp.138-143
• /
• 2020

In this study, we produced a coil of micro-pattern that can be used for electromagnetic wave absorber, heating material, wireless charging, sensor, antenna, etc. by using electrochemical additive manufacturing method. Currently, it contains research contents for manufacturing a micro pattern coil having practicality through control of process control variables such as applied voltage, distance between electrode, and nozzle injection. Circulation of the electrolyte through the nozzle injection control can significantly contribute to improving the surface characteristics of the coil because of minimizing voltage fluctuations that may occur during the additive manufacturing process. In addition, by applying the pulse method in the application of voltage, the lamination characteristics of the plated body were improved, which showed that the formation of a fine line width plays an important role in the production of a micro pattern coil. By applying the pulse signal to the voltage application, the additive manufacturing characteristics of the produced product were improved, and it was shown that the formation of a fine line width plays an important role in the production of a micro pattern coil.

• Journal of the Optical Society of Korea
• /
• v.19 no.6
• /
• pp.695-699
• /
• 2015

A high spectral resolution lidar (HSRL) system based on injection-seeded Nd:YAG laser and iodine absorption filter has been developed for the quantitative measurement of aerosol and cloud. The laser frequency is stabilized at 80 MHz by a frequency locking system and the absorption line of iodine cell is selected at the 1111 line with 2 GHz width. The observations show that the HSRL can provide vertical profiles of particle extinction coefficient, backscattering coefficient and lidar ratio for cloud and aerosol up to 12 km altitude, simultaneously. For the measured cases, the lidar ratios are 10~20 sr for cloud, 28~37 sr for dust, and 58~70 sr for urban pollution aerosol. It reveals the potential of HSRL to distinguish the type of aerosol and cloud. Time series measurements are given and demonstrate that the HSRL has ability to continuously observe the aerosol and cloud for day and night.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.867-868
• /
• 2004

The maximum width of HAZ of SA508치.3 steel produced by overlay RPV cladding was approximately 10 mm and it was composed of variety of microstructures with various grain size and precipitates. In addition, along the weld fusion line there formed a heavy carbide precipitation zone in the width of $20{\sim}30\;{\mu}m$. 2. As the specimen sampling position approached to the weld fusion line, the increase in yield and tensile strength was approximately 90 and 40 MPa, respectively. Meanwhile, the plastic fracture strain reduced from 14 to 8 percent. 3. The lowest SP energy and the highest ductile to brittle transition temperature in the HAZ were observed at the coarse- and fine-grained HAZ.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1552-1555
• /
• 2005

We have studied the inkjet patterning of synthesized aqueous silver nano-sol on interface-controlled ITO glass substrate. Furthermore, we designed the conductive ink for direct inkjet patterning on bare ITO glass substrate. The first, the highly concentrated polymeric dispersant-assisted silver nano sol was prepared by variation of molecular weight and control of initial nucleation and growth of silver nanoparticles. The high concentration of batch-synthesized silver nano sol was possible to 40 wt%. At the same time the particle size of silver nanoparticles was below $10{\sim}20nm$. The second, the synthesized silver nano sol was inkjet - patterned on ITO glass substrate. The connectivity and width of fine line depended largely on the wettability of silver nano sol on ITO glass substrate, which was controlled by surfactant. The relationship was understood by wetting angle. The fine line of silver electrode as fine as $50{\sim}100\;{\mu}m$ was successfully formed on ITO glass substrate. The last, the direct inkjet-patternable silver nano sol on bare ITO glass substrate was designed also.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.87.2-87.2
• /
• 2013

We studied a fine-scale half ring-like structure around a pore seen from the high spectral and the high spatial resolution data. Our observations were carried out using the Fast Imaging Solar Spectrograph (FISS) and the InfraRed Imaging Magnetograph (IRIM) installed at the 1.6 meter New Solar Telescope of Big Bear Solar Observatory (BBSO) on 2012 July 19. During the observations, we found a fine-scale half ring-like structure located very close to a pore (~0.4 arcsec apart from the pore). It was seen in the far wing images of the $H{\alpha}$ and Ca II $8542{\AA}$ lines, but it was not seen in the line center images of two lines. The length of the structure is about 4200 km and the width is about 350 km. We determined its line-of-sight velocity using the Doppler shift of the centroid of the Ti II line ($6559.6{\AA}$, close to the $H{\alpha}$ line) and determined horizontal velocity using the NAVE method. we also investigated the magnetic configurations using the Stokes I, Q, U, and V maps of the IRIM. As a results, we found that it has a high blue-shift velocity (~2km) faster than the photospheric features and has a strong horizontal component of the magnetic field. Based on our findings, we suggest that it is associated with small flux emergence, which occurs very close to the pore. Even though it is very small structure, this kind of magnetic configuration can be in chare of the upper chromosphere heating, especially above the pore.