• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.1093-1096
• /
• 2004

Bearings are elementary machinery component which loads and do rotating motion. Excessive loads or many other reasons can cause incipient faults to be created and grown in each component. Moreover, it happens that incipient faults which were caused by manufacturing or assembling process' errors of the bearings are created. Finding the incipient faults as early as possible is necessary to the bearings in severe condition: high speed or frequently varying load condition, etc. How early we can detect the faults has to do with how the detection algorithm finds the fault information from measured signal. Fortunately, the bearing fault signal makes periodic impulse train. This information allows us to find the faults regardless how much noise contaminates the signal. This paper shows the basic signal processing idea and experimental results that demonstrate how good the method is.

• 한국정보통신학회논문지
• /
• 제16권2호
• /
• pp.313-318
• /
• 2012

본 논문에서는 $30{\mu}m$ 이하의 초 미세 피치를 가진 칩 온 필름(chip-on-film, COF)에서 자주 발생하는 결함을 자동으로 검출할 수 있는 시스템을 제안한다. 개발된 시스템은 초 미세 패턴의 개방 및 단락 결함 뿐만아니라 소프트 개방 및 소프트 단락을 신속히 검출할 수 있는 회로 및 기술이 적용되어 있다. 결함 검출의 기본 원리는 결함 전의 패턴 저항값과 결함 후의 패턴 저항값 차에 의해 발생하는 미세 차동 전압을 읽어서 결함 유무를 판단한다. 또한 미세전압 차를 증폭시켜 결함 유무를 쉽게 판단할 수 있도록 고주파 공진기를 이용한다. 제안된 시스템은 초미세 패턴 COF 검사 과정에서 발생하는 다양한 결함을 신속하고 정확히 검출할 수 있으므로 기존의 COF 검사 시스템의 대안이 될 것으로 기대한다.

• 대한전기학회논문지:전력기술부문A
• /
• 제52권2호
• /
• pp.114-120
• /
• 2003

According to the use of distribution automation systems, the function to find or to search a fault phase is necessary for automatic switches in a distribution substation. In this paper, two algorithms are developed to fine the fault circuit and the fault phase for the automatic switches in substation with ungrounded power system. One is the fault circuit searching method using the zero sequence voltage at the bus and zero sequence current of circuit current and the other is to find the fault phase using the line voltage and zero sequence current. The developed algorithms are tested in the case study simulations. An ungrounded power system is modeled by EMTP as a case study system. The developed algorithms are tested in the case study simulations and each shows correct results.

• Structural Monitoring and Maintenance
• /
• 제5권1호
• /
• pp.51-65
• /
• 2018

A number of sensing techniques have been implemented for detecting defects in civil infrastructures instead of onsite human inspections in structural health monitoring. However, the issue of faults in sensors has not received much attention. This issue may lead to incorrect interpretation of data and false alarms. To overcome these challenges, this article presents a deep learning-based method with a new architecture of Stateful Long Short Term Memory Neural Networks (S-LSTM NN) for detecting sensor fault without going into details of the fault features. As LSTMs are capable of learning data features automatically, and the proposed method works without an accurate mathematical model. The detection of four types of sensor faults are studied in this paper. Non-stationary acceleration responses of a three-span continuous bridge when under operational conditions are studied. A deep network model is applied to the measured bridge data with estimation to detect the sensor fault. Another set of sensor output data is used to supervise the network parameters and backpropagation algorithm to fine tune the parameters to establish a deep self-coding network model. The response residuals between the true value and the predicted value of the deep S-LSTM network was statistically analyzed to determine the fault threshold of sensor. Experimental study with a cable-stayed bridge further indicated that the proposed method is robust in the detection of the sensor fault.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.314-315
• /
• 2013

• 한국광물학회:학술대회논문집
• /
• 한국암석학회.한국광물학회 2000년도 공동학술발표회 논문집
• /
• pp.24-24
• /
• 2000

We studied about petrological characteristics of the Bangeujin granite belongs to porphyritic biotite granite, petrogenesis of the enclaves in the granite and contact metamorphism of the sedimentary rock around the granite. The enclaves in the granite are concentrated in the eastern part of the Mipo fault but in the western part, these are rare. The enclaves can be divided into three types according to the petrographical characteristics. These three types are: (1) enclaves having few phenocrysts and fine grained igneous texture and ellipsoid is predominant; (2) enclaves similar In petrographical characteristics and having many phenocrysts considered as being originated from the granitic host rock; and (3) enclaves corresponding to granite in mode composition, having large phenocrysts and of which the matrix is corresponding to fine granular. First two types are correspond to mafic micro granular enclaves and the third is corresponds to felsic microgranular enclaves. In addition, the felsic microgranular enclaves capture the mafic microgranular enclaves. The fact that the compositions of biotite and plagioclase in the enclaves are nearly identical with those of biotite and plagioclase in the granitic host rock is considered as the results of supporting magma mingling. The major elements show well the linear variations as the SiOz$.$ content increases. The rare earth elements content decrease with increasing SiOz content, interpreted as the results of magma mingling. Therefore, we can conclude that the Bangeujin granite captured the felsic microgranular enclaves formed by collapse of early chilled margin during the crystallization and there was magma mingling by the injection of the mafic magma after that time. In addition, these aspects are predominant in the eastern part of the Mipo fault is considered as related to the fault movement.vement.

• 지질공학
• /
• 제13권2호
• /
• pp.193-205
• /
• 2003

양산단층과 동래단층 사이를 통과하여 건설하는 지방도를 포함하는 조사지역에는 중생대 백악기에 분출 및 관입한 안산암질암, 세립질 화강암, 반상 화강암 및 흑운모 화강암이 분포한다. 또한 이 지역은 양산단층과 동래단층 사이에서 북동방향의 명곡단층과 북북동방향의 법기단층이 발달하고 있다. 이 지역의 절리의 특성은 화강암이 분포하는 지역에서 절리의 경사각이 30도 미만의 sheeting joint가 발달하며 이외 경사각이 70도 이상 고각의 절리는 북동방향, 북서 방향 및 거의 동서방향의 3조의 절리군이 발달한다. 이들 절리의 간격은 대개 20cm이상의 보통의 간격상태로 암반이 심하게 파괴되지 않았음을 볼 수 있고, 또한 벽면강도도 일반적으로 100MPa이상으로 원암의 강도와 차이를 보이지 않아 절리가 심하게 변형작용을 받았다고는 볼 수 없다 따라서 이 지역은 양상단층과 동래단층인 두 대단층의 사이에 위치하는 암반이지만 이들 단층의 손상대(Damage zone)의 범위가 좁아 지반 상태가 비교적 양호한 것으로 판명되었다.

• Journal of Electrical Engineering and information Science
• /
• 제1권1호
• /
• pp.118-128
• /
• 1996

In safety critical hard real-time systems, a timing fault may yield catastrophic results. In order to eliminate the timing faults from the fast responsive real-time control systems, it is necessary to schedule a code based on high precision timing analysis. Further, the schedulability enhancement by having multiple processors is of wide spread interest. However, although an instruction level parallel processing is quite effective to improve the schedulability of such a system, none of the real-time applications employ instruction level parallel scheduling techniques because most of the real-time scheduling models have not been designed for fine-grain execution. In this paper, we present a timing constraint model specifying high precision timing constraints, and a practical approach for constructing static schedules for a VLIW execution model. The new model and analysis can guarantee timing accuracy to within a single machine clock cycle.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 춘계학술대회 논문집 에너지변화시스템부문
• /
• pp.259-262
• /
• 2009

Several universities in Korea are beginning studies related to soft stamping processes but since the studies are done with manual works thus systematic tests can't be performed due to difficulties in producing reproducible and repeatable fine patterns. Therefore, the phenomenon of destruction of the pattern forms of elastic polymers occurred during working because of inconsistent printing pressures and pinting time and there have been difficulties in maintaining flatness or producing uniform and fault-free fine structures in pinting large areas and also, there have been difficulties in multi-layered processes as patterns were changed by contacts in registering and errors in alignments. The purpose of development of this technology is to improve the process of soft lithography so that contacts between PDMS stamps and metal coated substrates in order to develop a stamp printing device that can not only shorten but also optimize processes, secure reproducibility and repeatability and is advantageous in printing large areas. Also, using this technology, this author is to develop equipment technologies and applied technologies for nano grade pattern printing processes with new concepts based on fine contact printing processes in order to apply them to diverse nano pattering processes.

• International Journal of Computer Science & Network Security
• /
• 제24권7호
• /
• pp.123-127
• /
• 2024

Cloud computing services has gained increasing popularity in recent years for supporting various on demand and scalable services for IT consumers where there is a need of less investment towards infrastructure. While storage architecture of cloud enjoys a more robust and fault-tolerant cloud computing network, such architecture also poses a number of security challenges especially when applied in applications related to social networks, Financial transactions, etc. First, as data are stored and maintained by individual virtual machines so Cloud resources are prone to hijacked. Such attacks allow attackers to create, modify and delete machine images, and change administrative passwords and settings successfully. hence, it is significantly harder to ensure data security. Second, Due to dynamic and shared nature of the Cloud, data may be compromised in many ways. Last but not least, Service hijacking may lead to redirect client to an illegitimate website. User accounts and service instances could in turn make a new base for attackers. To address the above challenges, we propose in this paper a distributed data access control scheme that is able to fulfil fine-grained access control over cloud data and is resilient against strong attacks such as compromise and user colluding. The proposed framework exploits a novel cryptographic primitive called attribute-based encryption (ABE), tailors, and adapts it for cloud computing with respect to security requirements