• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.89-96
• /
• 1999

Manufacturing conditions of the porous alumina mold were established to overcome various limits of the gypsum mold. For the preparations of the porous alumina mold, an activated charcoal was added to the Al2O3 with the wt% variation and then mixed. The binary slurry was study dispersed based on the examination of the ESA and rheological behaviro. The cylinder type alumina mold was cast in the gyspum mold and characterized by the shrinkage rate at the variable sintering temperature and the resistance against wear. It was proper to make a sintering of the Al2O3 by the surface diffusion which was non-shrinkage sintering mechansim, and intergranular neck growed stronger while sintering was being made. We studied a sintering by three categories; 1) thermodynamic method below 1,000$^{\circ}C$, 2) kinetic method above 1,000$^{\circ}C$ and 3) combined method. In the results of the respective works, combined method was superiro to the others. The prepared Al2O3 mold had relatively high strength, low drying rate, the resistance against the acid or base and good casting behavior.

• Journal of the Korean Ceramic Society
• /
• v.55 no.5
• /
• pp.473-479
• /
• 2018

Highly toxic gases such as hydrogen sulfide ($H_2S$), carbon dioxide ($CO_2$), and ammonia ($NH_3$) are generated by both nature and human activities and affect human health. In this research, activated carbon combined with $Ca(OH)_2$ and $CaCO_3$ (AC-CO and AC-CC, respectively) were fabricated and applied in absorbing toxic gases from air pollutants. Activated charcoal powder was compressed in the form of pellets and used in the designated conditions. The optimum operating conditions and material properties, such as adsorption capacity, effect of weight ratio of the mixture, and hardness, have been investigated after combining with the calcium derivative. The good performance exhibited in this study suggests that this material is expected to be an effective and economically viable adsorbent for $NH_3$, $CO_2$, and $H_2S$ removal from the air system.

• Korean Journal of Veterinary Research
• /
• v.33 no.3
• /
• pp.471-478
• /
• 1993

Culicoides arakawae is a kind of the main blood sucking insects of domestic fowls and serves as a vector of Leukocytozoom caulleryi, the causative protozoon of chicken leukocytozoonosis. In this study, the complete life history of C arakawae was cycled by laboratory colonization. Adult midges were collected from various poultry farm by light trap. The laboratory colonization was performed under the conditions of constant temperature of $25{\pm}1^{\circ}C$ and relative humidity of 80% or above. The hatched larvae were cultured in larval medium consisted of rice field mud and activated charcoal powder. The surface of medium was continuously flowed with biologically conditioned water. The fine powder meal composed of pellet feed for mice and equal mount of yeast was supplied for feeding larvae at every 72 hours. The life cycle completed at $25^{\circ}C$ in 35~35 days ; the period of preoviposition, egg. larval and pupal stage was 2~3, 3~4, 28~30 and 3 days, respectively. The measurements of the eggs, the lst instar larvae, the 4th instar larvae and pupae was $36.28{\mu}m{\pm}1.95$, $13.58{\mu}m{\pm}0.72$, $4000{\mu}m{\pm}1.47$ and $219.95{\mu}m{\pm}6.25$ in $mean{\pm}S.D.$, respectively. In order to confirm experimental colonization of C arakawae in laboratory, the colonized adult midges were allowed to suck blood from chicken infected with L caulleryi. The oocysts and sporozoites could be identified in midguts and salivary grands of engorged midges at 72 hours after blood sucking.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.5
• /
• pp.755-763
• /
• 2010

Fine sediment loadings from agricultural watersheds have led to habitat degradation in Lake Takkobu, northern Japan. Fifteen lake sediment core samples were obtained and analyzed to develop a chronology using physical sediment characters, $^{137}Cs$, and tephra. The reconstructed sedimentation rates over the past ca 300 years suggested that sedimentation rates increased drastically after land use development. With a natural sedimentation rate of 0.1-1.1 mm $year^{-1}$ until 1898, lake sedimentation accelerated to 0.6-12.8 mm $year^{-1}$ after 1898. The sedimentation rates after land use change, such as forestry, river engineering works, and agricultural development, were about 6-12 times higher than that under natural conditions, leading to accelerated lake shallowing over the last ca 100 years. Sedimentation rates between 1898 and 1963 differed with location in the lake because of spatial variation in the sediment flux from the contributing rivers and their watersheds. The sedimentation rate in the southern zone between 1898 and 1963 was significantly higher than that in the middle and northern zones, reflecting active sediment production associated with forestry for charcoal production and canal construction for transportation in the southern watersheds and wetlands. The sedimentation rate after 1963 did not vary among the three zones, because decreasing sedimentation was found in most of the southern sites whereas an increasing trend was observed in the middle and northern sites. This result can be explained by shallowing of lake-bottom morphology with sedimentation and the resultant reduction of sediment retention capacity in the southern zone. Moreover, the sedimentation rate at sampling sites close to river mouths increased by 5-32 times compared with natural rates before 1898. The Kushiro River, into which Lake Takkobu drains under regular flow conditions, further contributed to an increased sedimentation rate, because water from the Kushiro River flows back into Lake Takkobu during floods.

• Resources Recycling
• /
• v.11 no.1
• /
• pp.3-8
• /
• 2002

In order to make the high purity Mn$_3$O$_4$powder for the raw material of soft ferrite, Mn is extracted from the dust and the extracted solution is refined. The dust is generated in producing a medium-low carbon ferromanganese and contains 90% Mn$_3$O$_4$. Mn$_3$O$_4$in the dust was reduced into MnO by roasting with charcoal. Injection of the 180g/L of the reduced dust into 4N HCI solution increased pH of the leaching solution higher than 5 and then a ferric hydroxide was precipitated. Because the ferric hydroxide co-precipitates with Si ion etc, Fe and Si ion was removed from the solution and the about 10% Mn solution was obtained. The solution was diluted with water to Mn-15000 ppm and $NH_4$F was injected into the diluted solution at $70^{\circ}C$ to the F-3000 ppm. As a result, Ca ion is precipitated as $CaF_2$and the residual concentration of Ca was 14 ppm. Injection of the equivalent (NH$1.5M_4$)$_2$$CO_3$solution as 2 L/min at $25^{\circ}C$ into the above solution precipitated a fine and high purity $MnCO_3$powder. The deposition was filtrated and roasted at $1000^{\circ}C$ for 2 hours. As a result, $MnCO_3$powder is converted into $Mn_3$$O_4$powder and it had $8.2\mu$m of median size. The final production is above 99% $Mn_3$$O_4$powder and it satisfied the requirement of high purity $Mn_3$$O_4$powder for a raw material of soft ferrite.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.31-42
• /
• 2007

To investigate the pyrolytic and anatomical characteristics of Korean softwood, Pinus densi-flora, Pinus rigida and Larix leptolepis, and hardwood, Acer palntatum, Fraxinus rhynchophylla and Quercus variabilis, chemical components analysis, TG-DTA (Thermogravimetric Analysis & Differential Thermal Analysis), MBA (Methylene Blue Adsorption) test and SEM observation were carried out. For TG-DTA, samples were carbonized up to $800^{\circ}C$ at the heating rate of $10^{\circ}C$/min under $N_2$ flows 1 l/min using thermogravimetric analyzer. Chemical component analysis of all samples resulted in typical contents of major wood component. In TG-DTA results, softwood showed higher char yield than hardwood, and lignin displayed the highest char yield among the major wood components. All samples showed typical TGA, DTG and DTA curves for wood pyrolysis except a few differences between softwood and hardwood. Content of lignin influenced its pyrolysis characteristics, while molecular structure of lignin affected not only the weight loss but also the yield of char. In MBA test results, MBA of softwoods was higher than that of hardwoods. Char of Pinus densiflora showed the highest MBA, but its degree was lower than activated carbon or fine charcoal about 23 and 4 times, respectively. SEM observation showed carbonization process preserves wood structure and retain the micro-structure of wood fibers.