• 한국세라믹학회지
• /
• 제31권3호
• /
• pp.337-345
• /
• 1994

The reaction-sintered alumina and zirconia-alumina ceramics having low firing shrinkage were prepared from the Al/Al2O3 or Al/ZrO2(Ca-PSZ) powder mixtures via the attrition milling. And in this milling process the effect of the characteristics of used powders was investigated. Attrition milling was much more effective in reducing the particle size of ceramic/metal mixed powders than ball milling. Powder mixtures of flake-type Al with coarse alumina was much more effectively comminuted by the attrition milling than the mixtures of globular-type Al with coarse alumina powders. And coarse alumina than fine alumina was much more beneficial in cutting and reducing the ductile Al particles. In the contrary to Al/Al2O3 powder mixtures, Al/ZrO2 powder mixtures was not effectively comminutd. But whether using the alumina ball media or attrition milled with Al2O3 powder rather than Al, the milling efficiency was much more increased.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1292-1293
• /
• 2006

A non-equilibrium powder metallurgy processing such as an MA/SPS (Mechanical Alloying / Spark Plasma Sintering) process is examined in a Ti-48moll%Al. TiAl intermetallic compound is a potential light-weight/high-temperature structural material. One of the major problems, however, limiting the practical use of the material is its poor workability. From this point, the powder metallurgy (PM) processing route has been attractive alternative of the conventional processing for such material The MA/SPS process is able to apply to a LIGA process. Optimization of the pseudo-superplasticity enables to fabricate micro-parts made of fine grained ceramics composites of TiAl by the LIGA process.

• The Korean Journal of Ceramics
• /
• 제1권4호
• /
• pp.185-190
• /
• 1995

Tribological behavior of the diamond-like carbon (DLC) films sliding on floppy disk has been investigated. Hydrogenated DLC films have been prepared by plasma enhanced chemical vapor deposition (PECVD) using methane and hydrogen mixture in different volume ratios on ferrite substrates. DLC films show lower friction coefficients (0.2~0.4) than those of the uncoated ferrite(0.4~0.5). DLC films containing more hydrogen exhibit higher wear resistance. To investigate the roughness effect on wear, the substrates were polished with SiC papers prior to deposition. Too fine or too rough DLC surfaces result in poor wear resistance. Wear resistance of annealed DLC films at higher temperature slightly increases with respect to as-deposited film.

• 한국세라믹학회지
• /
• 제23권4호
• /
• pp.11-16
• /
• 1986

$BaTiO_3$ ceramics powder was prepared by coprecipitation method either in oxalic acid solution or in potassium hydroxide solution. Thermal decomposition of coprecipitated $BaTiO(C_2O_4)_2$.$4H_2O$ powder in oxalic acid solution was investigated by means of Themogravimetry Differential Thermal Analysis and X-ray Diffraction Analysis. Low temperature decomposition of coprecipitated $BaTiO(C_2O_4)_2$.$4H_2O$ caused narrow particle size distribution whereas high temperature decomposition caused fairly wide particle size distribution by partial sintering. As the reaction time increased the average particle size of coprecipitated $BaTiO_3$ powder in KOH solution was increased. The most narrow paticle size distribution was obtained when the coprecipi-tates were ripened for 4hrs.

• 한국전기전자재료학회논문지
• /
• 제16권8호
• /
• pp.681-687
• /
• 2003

The syntheses of LaNiO$_3$Perovskite crystalline phase from mixtures of La$_2$O$_3$and NiO via it mechanochemical(used planetary mill) and a wet ball mill process were investigated. A single and stable LaNiO$_3$perovskite crystalline phase was successfully prepared by using a heat free mechanochemical process which produced a fine amorphous powder, while that phase was not formed in a wet ball mill process which needed heat treatment ranging from 500 to 150$0^{\circ}C$ and produced a coarse powder. It was shown that the LaNiO$_3$ceramics made of the mechanochemically synthesized powder possesed a good metallic characteristic.

• 한국세라믹학회지
• /
• 제48권5호
• /
• pp.463-466
• /
• 2011

Wet foams formed through direct foaming were stabilized using various concentrations of amiphiphilic particles that could control pore size and porosity. These porous materials showed moderate strength upon compression with high porosity. Bubble size and wet foam stability were tailored by amphiphile concentration, particle concentration, contact angle, and pH of the suspension to obtain crack-free porous solid after sintering. Closed and open pores were obtained with sizes of 30~300 ${\mu}m$ and porosities of over 80%.

• 전기학회논문지
• /
• 제60권2호
• /
• pp.349-351
• /
• 2011

The formation of oxide superconducting phase fabrication of superconducting wire materials and fabrication of precise superconducting material were studied for developing superconductor application technique. The $ZrO_2$ addition reduced the particle size $BaZrO_3$ trapped in the matrix after the sintering growth. The added $ZrO_2$ was converted to fine particles of $BaZrO_3$ which is the conventional sintering temperature for YBaCuO, $Y_2Ba_1Cu_1O_5$ and CuO are formed as by products of the reaction between $ZrO_2$ and YBaCuO phase. The formation of highly $BaZrO_3$ particle appears to be responsible for the refinement of $BaZrO_3$ phase after the citric acid sintering process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1586-1588
• /
• 2003

The Pb$(Zr{_{0.7}}Ti_{0.3})O_3$[PZT(70/30)] thin films were fabricated on Pt/$TiO_2/SiO_2$/Si substrate by RF sputtering method. The effects of Ar/$O_2$ ratio on the structural and dielectric properties of PZT thin fillms were investigated. In the case of the PZT thin films deposited with condition of 50/50$(Ar/O_2) $ ratio, the grain of the PZT thin films were fine and uniform. Increasing of $O_2$ ratio, the dielectric constant was increased. In this case the dielectirc constant and dielectric loss of PZT thin fims were about 627 and 0.010, respectively.

• Nuclear Engineering and Technology
• /
• 제48권2호
• /
• pp.299-303
• /
• 2016

Prompt gamma activation analysis using a thermal neutron-guided beam at Japan Atomic Energy Agency JRR-3M was applied for the precise determination of Si in silicon nitride ceramic reference materials [Japan Ceramic Reference Material (JCRM) R 003]. In this study, the standard addition method coupled with internal standard was used for the nondestructive determination of Si in the sample. Cadmium was used as internal standard to obtain the linear calibration curves and to compensate for the neutron beam variability. The analytical result of determining Si in JCRM R 003 silicon nitride fine powder ceramic reference materials using prompt gamma activation analysis was in good agreement with that obtained by classical gravimetric analysis. The relative expanded measurement uncertainty (k = 2) associated with the determined value was 2.4%.

• 한국결정성장학회지
• /
• 제7권1호
• /
• pp.167-173
• /
• 1997

$ZnFeO_4$ 분말은 금속 질산염을 수산화 칼슘으로 침전시켜 이를 1,4-부탄에디을 속에서 비교적 고온고압을 가하여 얻어졌다. 미분말이 얻어진 온도는 225-$300^{\circ}C$, 압력은 1-3.5 MPa이였다. 분말의 미세구조는 주사전자현미경으로 결정상은 X-선 회절 분석으로 행하였다. 분말의 물성과 반응온도, 반응시간 및 농도의 관계를 조사하였다. $ZnFe_2O_4$ 분말의 평균입자 크기는 반응온도와 시간이 증가함에 따라 증가하였다. $270^{\circ}C$에서 8시간 반응을 행한 경우의 평균입자 크기는 약 50 nm였다.