• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2211-2216
• /
• 2007

Liquefied gas vaporizer means machine to vaporize the liquefied gas as liquid nitrogen($LN_2$), liquefied natural gas(LNG), liquid oxygen($LO_2$) etc. In the air type vaporizer, the frozen dew is also created by temperature drop (below 273 K) on vaporizer surface. This problem increases as the time progresses and humidity increases. In addition, the frozen dew gradually becomes frost deposit consequently, heat transfer through vaporizer decreases because frost deposit form adiabatic sheet. Because of this reason, recent vaporizer system is installed as parallel type, this vaporizer system needs more expensive installation costs and more space. This paper was investigated on the heat transfer characteristics of liquefied gas vaporizer with super low temperature and this paper was carried out the numerical about air heating vaporizer with super low temperature. The numerical analysis on the heat transfer was studied on the effect of geometric parameters of the vaporizer, which are length 1000 mm of 4fin75le type vaporizer. 4fin75le means number of fin is 4 and height of fin is 75 mm.

• Advances in aircraft and spacecraft science
• /
• 제5권4호
• /
• pp.411-430
• /
• 2018

This computational study examines the augmentation of classic 2-D Rayleigh-$B{\acute{e}}nard$ convection by the addition of periodically-spaced transverse fins. The fins are attached to the heated base of the cavity and serve to partition the cavity into 'units' with different aspect ratios. The respective impacts upon heat transfer of the fin configuration parameters - including spacing, height, thickness and thermal conductivity - are systematically examined through numerical simulations for a range of laminar Rayleigh numbers (0 < Ra < $2{\times}10^5$) and reported in terms of an average Nusselt number. The selection of the low Rayleigh number regime is linked to likely scenarios within aerospace applications (e.g. avionics cooling) where the cavity length scale and/or gravitational acceleration is small. The net heat transfer augmentation is found to result from a combination of competing fin effects, most of which are hydrodynamic in nature. Heat transfer enhancement of up to $1.2{\times}$ that for a Rayleigh-$B{\acute{e}}nard$ cavity without fins was found to occur under favorable fin configurations. Such configurations are generally characterized by short, thin fins with half-spacings somewhat less than the convection cell diameter from classic Rayleigh-$B{\acute{e}}nard$ theory. In contrast, for unfavorable configurations, it is found that the introduction of fins can result in a significant reduction in the heat transfer performance.

• 대한기계학회논문집B
• /
• 제27권3호
• /
• pp.347-356
• /
• 2003

The characteristics of near wakes of circular cylinders with serrated fins are investigated experimentally using a hot-wire anemometer for various freestream velocities. Near wake structures of the fin tubes are observed using a phase average technique. With increasing fin height and decreasing fin pitch. oscillation of streamwise velocity increases. It file oscillation of lateral velocity decreases. The time averaged V-component velocity distribution of the finned tube is contrary to that of the circular cylinder due to the different strength of entrainment flow. This strength is affected by the distance of (equation omitted) = 1.0 contour lines. (equation omitted) = 1.0 contour line approaches to the wake center line when the fin density is increased. When the distance between (equation omitted) = 1.0 contour lines comes close the shear force should be increased and the flow toward the wake center line can be more strengthened because of the shear force. Factors related to the velocity recovery in the near wake of the finned tube are attributed to tile turbulent intensity, the boundary layer thickness. the position and strength of entrainment process.

• 한국산학기술학회논문지
• /
• 제20권8호
• /
• pp.579-585
• /
• 2019

수중 표적의 탐지 효율을 증대시키기 위하여 능동 예인 음탐기는 적정 심도에서 바른 자세로 예인 되어야 한다. 본 연구에서는 능동 예인 음탐기의 꼬리 날개 형상이 예인 자세 및 예인 안정성에 미치는 영향을 확인하기 위하여 축소 모형 실험 2회 및 해상 실험 1회를 수행하고 그 결과를 분석하였다. 축소 모형 실험은 선형 수조에서 꼬리 날개 형상에 따른 속력 별 예인 거동을 측정하였으며, 축소 모형 실험에 활용된 꼬리 날개 형상은 I 형 꼬리 날개 1개와 Y 형 꼬리 날개 4개로 총 2종 5개에 대하여 실험을 수행하였다. 1차 축소 모형 실험에서는 Y형 꼬리 날개가 I 형 꼬리 날개 대비 예인 자세 및 예인 안정성이 우수함을 확인하였다. 2차 축소 모형 실험에서는 Y형 꼬리 날개를 기본으로 수직 꼬리 날개 높이 증가, 하부 수평 꼬리 날개 경사각 적용 형상에 대하여 속력 별 거동 특성을 확인하였으며, 하부 수평 꼬리 날개 경사각 적용 형상이 가장 우수한 성능을 나타내었다. 축소 모형 실험 결과를 검증하기 위해 실물 모형을 제작하여 해상 실험을 수행하였으며, 축소 모형 실험 결과와 유사함을 확인하였다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.1113-1118
• /
• 2006

A numerical investigation of single phase heat and flow characteristics in circular tubes with a single set of spiral micro fins was performed with varying geometrical parameters like fin height, spiral angle, and number of fins. The properties of $40^{\circ}C$ water was used as a working fluid to simulate a condenser and the RNG $k-{\epsilon}$ turbulence model was adopted. Calculation results were obtained in fully developed turbulent flow with constant surface heat flux boundary condition. Relative terms were introduced to investigate the substitution effect of conventional smooth tubes. The dimensionless terms were the heat transfer enhancement factor, the pressure drop penalty factor, and the efficiency index. Additionally, a numerical optimization was carried out to maximize thermal performance with the concept of the robust design. A statistical analysis showed that fin height interacts with number of fins and spiral angle.

• 항공우주시스템공학회지
• /
• 제14권3호
• /
• pp.1-9
• /
• 2020

본 논문에서는 델타 윙렛 와류 발생기와 후퇴익형 와류 발생기 그리고 가이드 베인이 핀-튜브 유동에서의 압력 손실과 전열 성능에 미치는 효과를 비교하는 연구를 진행하였다. 와류 발생기와 가이드 베인은 채널 높이와 튜브의 지름을 기준으로 무차원화하였고, 위치는 저자들의 연구 결과에 따라 각각의 형상이 우수한 지점을 선정하였다. 레이놀즈 수는 입구 속도와 튜브 지름을 기준으로 하여 1400~8000으로 선정하였다. 결과적으로 압력 손실은 레이놀즈 수 8000에서 가이드 베인이 기존 핀-튜브 대비 4.7% 감소하는 효과를 보였고, 전열 성능은 레이놀즈 수 3800에서 델타 윙렛 와류 발생기가 기존 핀-튜브 대비 33% 정도 증가하는 결과를 확인하였다.

• 대한기계학회논문집B
• /
• 제35권5호
• /
• pp.467-472
• /
• 2011

본 연구는 LED 조명기구와 같은 원형 모양에 적합한 원형 히트싱크의 주위의 열유동을 실험 및 해석적으로 분석하였다. 기존 복사 열전달을 고려하지 않은 상관식을 이용하여, 추가적으로 복사 열전달을 해석적으로 계산하였다. 본 해석 모델의 타당성을 실험적으로 확인하였다. 이 모델을 바탕으로 휜의 형상 및 열유속을 인자로 하여 히트싱크 평균 온도의 변화를 살펴보았다. 그 결과 열전달 성능을 최대로 할 수 있는 최적 휜의 길이가 존재하였고, 방사율이 클수록 형상 인자의 변화가 복사 열전달 변화에 미치는 영향이 상대적으로 감소하였다.

• 대한기계학회논문집B
• /
• 제25권1호
• /
• pp.117-123
• /
• 2001

In present study a methodology has been developed and applied for the optimum design and performance evaluation of microchannel heat sinks. The optimum design parameters include channel number and fin thickness. For a trial model of 127mm in length, 52.5mm in width, 16mm in height and 2.5mm in base thickness, the optimum channel number and the fin thinckness have been determined to be of 194 and 0.08359mm, respectively in laminar flow region. Performance of the optimally designed microchannel heat sinks has been compared with those having 50% and 150% of the number of channels. The results showed that the 50% and 150% designs increased the pumping power by 200% and 150%, respectively.

• 설비공학논문집
• /
• 제19권7호
• /
• pp.500-511
• /
• 2007

The Optimal solutions of the design variables in internally finned tubes have been obtained for three-dimensional periodically fully developed turbulent flow and heat transfer. For a trapezoidal fin profile, performances of the heat exchanger are determined by considering the heat transfer rate and pressure drop, simultaneously, that are interdependent quantities. Therefore, Pareto frontier sets of a heat exchanger can be acquired by integrating CFD and a multi-objective optimization technique. The optimal values of fin widths $(d_1,\;d_2)$, fin height(h) and helix angle$(\gamma)$ are numerical1y obtained by minimizing the pressure loss and maximizing the heat transfer rate within ranges of $d_1=0.5\sim1.5mm$, $d_2=0.5\sim1.5mm$, $h=0.5\sim1.5mm$, and $\gamma=0\sim20^{\circ}$. For this, a general CFD code and a global genetic algorithm(GA) are used. The Pareto sets of the optimal solutions can be acquired after $30^{th}$ generation.

• 설비공학논문집
• /
• 제15권10호
• /
• pp.860-869
• /
• 2003

Design optimization of the heat sink with 7${\times}$7 square pin-fins is performed numerically using the Computational Fluid Dynamics (CFD) and the Computer Aided Optimization (CAO). In the pin-fins heat sink, the optimum design variables for fin height (h), fin width (w), and fan-to-heat sink distance (c) can be achieved when the thermal resistance ($\theta$$_{j}$) at the junction and the overall pressure drop ($\Delta$p) are minimized simultaneously. To complete the optimization, the finite volume method for calculating the objective functions, the BFGS method for solving the unconstrained non-linear optimization problem, and the weighting method for predicting the multi-objective problem are used. The results show that the optimum design variable for the weighting coefficient of 0.5 are as follows: w=4.653 mm, h=59.215 mm, and c=2.667 mm. In this case, the objective functions are predicted as 0.56K/W of thermal resistance and 6.91 Pa of pressure drop. The Pareto optimal solutions are also presented.re also presented.d.