• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권4호
• /
• pp.462-470
• /
• 2015

In this study, we analyze the impacts of the trapezoidal fin shape of a double-gate FinFET on the electrical characteristics of circuits. The trapezoidal nature of a fin body is generated by varying the angle of the sidewall of the FinFET. A technology computer-aided-design (TCAD) simulation shows that the on-state current increases, and the capacitance becomes larger, as the bottom fin width increases. Several circuit performance metrics for both digital and analog circuits, such as the fan-out 4 (FO4) delay, ring oscillator (RO) frequency, and cut-off frequency, are evaluated with mixed-mode simulations using the 3D TCAD tool. The trapezoidal nature of the FinFET results in different effects on the driving current and gate capacitance. As a result, the propagation delay of an inverter decreases as the angle increases because of the higher on-current, and the FO4 speed and RO frequency increase as the angle increases but decrease for wider angles because of the higher impact on the capacitance rather than the driving strength. Finally, the simulation reveals that the trapezoidal angle range from $10^{\circ}$ to $20^{\circ}$ is a good tradeoff between larger on-current and higher capacitance for an optimum trapezoidal FinFET shape.

• 설비공학논문집
• /
• 제13권6호
• /
• pp.490-496
• /
• 2001

An experimental study on the behavior of the water hold-up by condensation of a fin-and-tube heat exchanger with regard to the surface characteristics, i.e., contact angle, was conducted. The static and dynamic contact angles were measured, and condensation experiments were conducted. Flow patterns on the fins with different surface characteristics were visualized. Results showed that the static contact angle is proportional to the dynamic contact angle within the range of this study. The water hold-up of the heat exchanger increases as the static or dynamic contact angle of its surfaces increases. Existence of transition of flow patterns was found as the static or dynamic angle increase. Due to the transition in the flow patterns, changes in the gradient of the water hold-up is occurred around the static angle of 8$0^{\circ}C$.

• 한국항공우주학회지
• /
• 제36권5호
• /
• pp.420-427
• /
• 2008

접힌 공력면이 전개하는 운동을 모사하기 위하여 전개 운동 방정식을 수립하고 공력면에 작용하는 모멘트 등을 모델링하였다. 공력에 의한 롤 모멘트는 정적 롤 모멘트와 감쇠 모멘트로 이루어져 있으며 정적 롤 모멘트는 전개 하중 측정을 위한 풍동 시험을 통하여 획득한 정적 롤 모멘트 계수로부터 계산된다. 롤 감쇠 계수는 패널법을 이용한 수치 해석을 통하여 산출되었는데 전개 각속도로부터 유발된 받음각에 상응하는 변위각을 공력면에 적용하여 수치해석을 하였다. 공력면 형상에 적용한 변위각은 회전 중심으로부터 공력면 끝단까지 선형적으로 증가하며 회전 중심에서는 변위가 없다. 롤 감쇠 계수는 전개 각속도에 따른 롤 모멘트 계수의 변화율로 계산되며 공력조건과 전개각의 함수이고 전개 각속도에 대해서는 일정하다고 가정하였다. 롤 감쇠를 포함하여 모사된 공력면의 전개 모사는 시험과 비교하여 유사한 결과를 보여주었다.

• 한국해양공학회지
• /
• 제30권1호
• /
• pp.18-24
• /
• 2016

Stabilizer fins are installed on each side of a ship to control its roll motion. The most common stabilizer fin is a rolling control system that uses the lift force on the fin surface. If the angle of attack of a stabilizer fin is zero or the speed is zero, it cannot control the roll motion. The Coanda effect is well known to generate lift force in marine field. The performance of stabilizer fin that applies the Coanda effect has been verified by model tests and numerical simulations. It was found that a stabilizer fin that applied the Coanda effect at Cj = 0.085 and a zero angle of attack exactly coincided with that of the original fin at α = 26°. In addition, the power needed to generate the Coanda effect was not high compared to the motor power of the original stabilizer fin.

• 한국연소학회지
• /
• 제1권1호
• /
• pp.19-29
• /
• 1996

This study is to investigate the characteristics of heat transfer of a horizontal tube, with radial fins of various configuration, immersed in a high temperature fluidized bed. The experimental heat transfer variation is compared with that of a smooth tube. The finned tubes and smooth tube, with outside and inside diameter of 48.6mm and 30.6mm, are made of steel tubes. The depth of the fin is 5mm, the rake angles of fin are $25^{\circ},\;35^{\circ},\;45^{\circ}$ and the widthes of fin for each rake angle are 0mm, 1mm, 2mm and 3mm. A bed temperature is fixed at $880\;{\pm}\;10^{\circ}C$. A granular refractory(silica sand) is used as a bed material with mean particle diameters of 1.22mm and 1.54mm. The maximum heat transfer coefficient is achieved with the rake angle of $25^{\circ}$ and the width of 0mm for the mean particle size 1.22mm. The coefficient is 2.14 times larger than that for a smooth tube. The rake angle for the maximum heat transfer coefficient depends on the particle size of bed material. Also the transfer coefficient decreases as the width of fin increases.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.152-158
• /
• 2004

An experimental study was performed to determine the fin-side heat transfer and pressure drop of a condenser for automobile. Five sample with different fin height and louver angle were tested, 9mm, 8mm, 7.5mm, 5.4mm and 4.5mm. Results are presented as plot of Colburn j-factor(or heat transfer coefficients) and friction factor(or pressure drop) against the Reynolds number(or inlet air velocity) based on louver pitch, in the range of 110 to 480. The results show that both heat transfer and pressure drop on the fin are mainly affected by the louver angle in a lower range of air velocity, but, by the fin height in a higher range of air velocity. The performance of 5.4mm fin is the highest, compared to other fin sample.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.371-374
• /
• 2006

초음속 유동장 내에서 돌출된 sharp fin형상에 의해 발생하는 충격파로 인한 열전달 특성변화 연구를 수행하였다. IR camera를 이용하여 마하 3의 유동 내에 attack angle이 $10^{\circ}$ 부터 $20^{\circ}$ 의 fin을 돌출시켜 생기는 충격파에 의한 바닥면 열전달 계수 변화를 측정하였으며, 유동장의 변화를 알아보기 보기 위해 oil flow method를 사용하였다.

• 설비공학논문집
• /
• 제9권4호
• /
• pp.454-461
• /
• 1997

Heat transfer and pressure drop for single phase flow of water in circular smooth and micro-fin tubes are measured. Copper tubes of 9.52 and 7mm outer diameter were used. The internal roughness in micro-fin tubes was formed by spiral grooves having $25^{\circ}$ helx angle, 0. 12mm fin height and 0.454mm pitch in 9.52mm tubes; $18^{\circ}$ helix angle, 0.15mm fin height and 0.322mm pitch in 7mm tubes. The measured friction factor and heat transfer coefficient are compared with relevant previous works, and the correlations for micro-fin tube are developed.

• 대한기계학회논문집
• /
• 제16권7호
• /
• pp.1381-1390
• /
• 1992

본 연구에서는 경사원주에서 발생하는 소용돌이 여기진동을 억제하기 위한 방 법으로 원주구조물 주위에서 발생하는 규칙적인 소용돌이 방출에 의한 여진력을 감소 시키도록 원주표면에 fin이나 wire를 부착시켜 단면형상을 바꾸는 방안을 실험적으로 검토한다. 즉, 밀폐순환식 유로을 이용하여 흐름에 경사되도록 탄성지지된 원주에 나선상의 fin과 wire를 감아, 경사각(.theta.)을 45, 60, 75, 90도, 나선피치각(.alpha.)을 30, 35, 40, 45, 50, 55, 60도, 나선권수(n)를 1,2,3으로 하여, 진동특성을 실험적으로 조사하고, plain원주와 비교하여 제진효과를 확인하며, 더우기 나선핀 원주의 최적형 상을 구하는 것을 목적으로 한다.

• 설비공학논문집
• /
• 제25권12호
• /
• pp.654-659
• /
• 2013

This paper presents a numerical optimization of louvered fins to enhance the JF factor in terms of the design parameters, including the fin pitch, the number of louvers, the louver angle, the fin thickness, and the re-direction louver length. We carried out a parametric study to select the three most important parameters affecting the JF factor, which were the fin pitch, number of louvers, and the louver angle. We optimally designed the louvered fin by using 3rd-order full factorial design, the kriging method, and a micro genetic algorithm. Consequently, the JF factor of the optimum model increased by 16% compared to that of the base model. Moreover, the optimum model reduced the pressure drop by 17% with a comparable heat transfer rate.