• Progress in Medical Physics
• /
• v.15 no.4
• /
• pp.202-209
• /
• 2004

Flat panel based digital radiography (DR) systems have recently become useful and important in the field of diagnostic radiology. For DRs with amorphous silicon photosensors, CsI(TI) is normally used as the scintillator, which produces visible light corresponding to the absorbed radiation energy. The visible light photons are converted into electric signal in the amorphous silicon photodiodes which constitute a two dimensional array. In order to produce good quality images, detailed behaviors of DR detectors to radiation must be studied. The relationship between air exposure and the DR outputs has been investigated in many studies. But this relationship was investigated under the condition of the fixed tube voltage. In this study, we investigated the relationship between the DR outputs and X-ray in terms of the absorbed energy in the detector rather than the air exposure using SPEC-l8, an X-ray energy spectrum model. Measured exposure was compared with calculated exposure for obtaining the inherent filtration that is a important input variable of SPEC-l8. The absorbed energy in the detector was calculated using algorithm of calculating the absorbed energy in the material and pixel values of real images under various conditions was obtained. The characteristic curve was obtained using the relationship of two parameter and the results were verified using phantoms made of water and aluminum. The pixel values of the phantom image were estimated and compared with the characteristic curve under various conditions. It was found that the relationship between the DR outputs and the absorbed energy in the detector was almost linear. In a experiment using the phantoms, the estimated pixel values agreed with the characteristic curve, although the effect of scattered photons introduced some errors. However, effect of a scattered X-ray must be studied because it was not included in the calculation algorithm. The result of this study can provide useful information about a pre-processing of digital radiography.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.40 no.3
• /
• pp.1-11
• /
• 2012

This study focused on establishing a natural rainwater circulation system using rainwater meant for relatively large urban development projects such as a new town development. In particular, when the location selection techniques for individual elements of a natural rainwater circulation system are developed for the integrated rainwater management, changes in hydrological environment will be minimized and the natural water circulation would be restored to realize the low impact development (LID). In that case, not only the excess will be reduced but water space and green areas in a city would also increase to improve the urban sustainability. First of all, there were five elements selected for the location selection of a rainwater circulation system intended for the integrated rainwater management: rainwater collection, infiltration, filtration, retention and movement spaces. After generating these items, the location selection items and criteria were defined for each of the five elements. For a technique to apply the generated evaluation items and criteria, a grid cell analysis was conducted based m the suitability index theory, and thematic maps were overlapped through suitability assessment of each element and graded based on the suitability index. The priority areas were identified for each element. The developed technique was applied to a site where Gim-cheon Innovation City development is planned to review its feasibility and limitations. The combined score of the overlapped map for each element was separated into five levels: very low, low, moderate, high and very high. Finally, it was concluded that creating a rainwater circulation system conceptual map m the current land use plan based on the outcome of the application would be useful in building a water circulation system at the de1ailed space planning stage after environmental and ecological planning. Furthermore, we use the results of this study as a means for environment-friendly urban planning for sustainable urban development.

• The Journal of Engineering Geology
• /
• v.18 no.4
• /
• pp.415-422
• /
• 2008

Pumping test was conducted to understand hydraulic conductivity for leaky confined aquifer with high permeability. Test aquifer was formed in $25{\sim}35\;m$ below ground surface at predetermined site of riverbank filtration which junction of Nakdong river and Milyang river in the Ttaan isle, Gimhae city, Korea Monitoring wells were located at intervals of 2 m and 5 m from pumping well in south-west direction (MW1 and MW2 wells) and northeast direction (MW3 and MW4 wells), respectively. Pumping test was continuously conducted for constant pumping rate of $2,500m^3/day$, hydraulic conductivity was estimated using AQTESOLV 3.5 program. Hydraulic conductivity were estimated to be $1.745{\times}10^{-3}m/sec$ for pumping well (PW), $2.452{\times}10^{-3}m/sec$ for between PW and MW1 wells, $2.161{\times}10^{-3}m/sec$ for between PW and MW2 wells, $2.270{\times}10^{-3}m/sec$ for between PW and MW3 wells and $2.591{\times}10^{-3}m/sec$ for between PW and MW4 wells. The function of hydraulic conductivity (K) as monitoring distance (d) were estimated to be logK = 0.0693logd - 2.671 for south-west direction (PW-MW1-MW2 line), logK = 0.0817logd - 2.655 for north-east direction (PW-MW3-MW 4 line). Scale exponent of hydraulic conductivity as test volume was estimated using Schulze-Makuch et al.(1999) method. Scale exponent of this aquifer was estimated to be 0.15. It means that test aquifer has very low heterogeneity. The radius of influence estimated using transmissivity, maximum groundwater level displacement, distance from pumping well and pumping rate during pumping test were 7.148 m for south-west direction and 6.912 m for north-east direction. The increasing rate of hydraulic conductivity from pumping well to maximum radius of influence were estimated to be 1.40 times for south-west direction and 1.49 times for north-east direction. Thus, heterogeneity of test aquifer was a little higher in north-east direction.

• Journal of Environmental Impact Assessment
• /
• v.28 no.6
• /
• pp.549-555
• /
• 2019

The purpose of this study is to ensure optimal operating conditions for improving the removal efficiency of phosphorus (P) and nitrogen (N) that are the causative agents of eutrophication by utilizing functional media. The main ingredients of the functional media used in this study are Si, Al, and Fe, SiO₂, KAlSiO₃O₈, Al₂O₂·2SiO₂O, H₃Al₂Si₂O₉, Fe₃O₄O), and berylite. To identify the maximum efficiency of the filtration process, the processing efficiency experiment was carried out according to flow method, velocity, and thickness of residual media. The flow method carried out two experiments, 50 m/day, 100 m/day, 150 m/day, 200 m/day, 250 m/day, and 20 cm, 40 cm, 50 cm, 60 cm, 80 cm of lead depth. Experiments have shown that SS, T-N, and T-P all showed higher elimination efficiency of the upflow current conditions than the downflow current conditions, and that the processing efficiency of the linearity is the highest at SS 50 m/day, T-N 150 m/day and T-P 100 m/day. In addition, the analysis of the removal efficiency according to the residual thickness showed that SS, T-N, and T-P all showed the highest efficiency at 60 cm. In addition, the analysis of the removal efficiency according to the residual thickness showed that SS, T-N, and T-P all showed the highest efficiency at 60 cm. It is considered desirable to set the top-down flow conditions and residual thickness of 60 cm and adjust the velocity of the line according to the target media for removal.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.11
• /
• pp.783-789
• /
• 2011

Recently, auto-thermal thermophilic aerobic digestion (ATAD) has a great attention for destruction of wasted sludge biomass in wastewater treatment plant. Reduction of sludge concentration has been successfully achieved with pilot scale ATAD and ceramic filtration process in field condition. However, high concentration of COD, total nitrogen (TN) and total phosphorus (TP) was observed in filtrate, which should be treated before recirculation of filtrate to biological wastewater treatment plant. This study was focused on removal of nitrogen and phosphorus contained in the filtrate of ATAD, using struvite crystallization method. The effect of operational and environmental parameters (such as, N, P and Mg ion concentration and molar ratio, pH, reaction time, agitation strength, seed dosage, and reaction temperature) on the treatment of TN and TP with struvite crystallization were evaluated. Magnesium (as $MgCl_26H_2O$) and phosphorus (as $K_2HPO_4$) ions were, if necessary, added to increase nitrogen removal efficiency by the crystal formation. Average concentration of $NH_4^+-N$ and $PO_4^{3-}-P$ of the filtrate were 1716.5 mg/L and 325.5 mg/L, respectively. Relationship between removal efficiencies of nitrogen and phosphorus and molar ratios of $Mg^{2+}$ and $PO_4^{3-}-P$ to $NH_4^+-N$ was examined. Crystal formation and nitrogen removal efficiencies were significantly increased as increasing molar ratios of magnesium and phosphorus to nitrogen. As molar ratio of $Mg^{2+}:PO_4^{3-}-P:NH_4^+-N$ were maintained to 2 : 1 : 1 and 2 : 2 : 1, removal efficiencies of nitrogen and phosphorus were 71.6% and 99.9%, and 93.8% and 98.6%, respectively. However, the effect of reaction time, mixing intensity, seed dose and temperature on the struvite crystallization reaction was not significant, comparing to those of molar ratios. Settled sludge volume after struvite crystallization was observed to be reduced with increase of seed dose and to be increased at high temperature.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.1
• /
• pp.42-50
• /
• 2009

Samples of subway dust were collected by the air filter system of 30 subway stations on Daegu subway line 1 in January 2008. Samples were sieved below 100 ${\mu}m$, and 14 elements were analyzed using ICP after acid extraction. Results obtained from the source assessment of trace elements using enrichment factor showed that Ca, Fe, K, Mg, Mn, Na, V were influenced by natural sources such as weathered rock and resuspended soil, while Cd, Cr, Cu, Ni, Pb and Zn were influenced by anthropogenic sources such as fuel combustion and waste incineration. Concentrations were remarkably higher in components from natural sources than in components from anthropogenic sources. Anthropogenic sources were significantly affected by indoor dusts than outdoor dusts. Results of pollution indices of heavy metals indicated that indoor dusts were more contaminated with heavy metal ions than outdoor dusts. The correlation analysis among trace elements indicated that components were much correlated in the order of natural sources-anthropogenic sources, anthropogenic sources-anthropogenic sources, natural sources-natural sources in both indoor and outdoor dusts. Trace element components of outdoor dusts were largely correlated than those of indoor dusts. In addition, indoor dusts were significantly affected by outdoor dusts rather than depth from the surface or the average daily number of subway passengers.

• Economic and Environmental Geology
• /
• v.46 no.1
• /
• pp.51-61
• /
• 2013

Researches on the oil recovery enhancement using the nanotechnology has recently been studied in the United States. The previous researches has focused mainly on the flow characteristics of nanoparticles in porous media, and the stability of the nano-emulsion itself. However, the analysis did not deal with the size effects between a nano-emulsion and the pore size which has an important role when nano-emulsion flows in the porous media. In this research, nano-based emulsion was fabricated which is able to be applied for the enhanced oil recovery techniques and its characteristics was analyzed. In addition, in order to identify the characteristics of nano-emulsions flowing through the porous media, the size effect was analysed by filtering test. According to the results, when the emulsion was fabricated, SCA(Silane Coupling Agent) or PVA(Poly Vinyl Alcohol) are added to improve the stability of emulsion. As the ratio of the decane to water increased, the viscosity of emulsion and the droplet size also increased. For the filtering test at the atmospheric conditions, the droplet did not go through the filter; only the separated water from the emulsion was able to be filtered. This phenomenon occurred because the droplet was not able to overcome the capillary pressure. At the filtering test by suction pressure, most of the emulsion was filtered over the filter size of $60{\mu}m$. However, the ratio of filtration was rapidly degraded at less than $45{\mu}m$ filters. This is caused due to deformation and destruction of the droplet by strong shear stress when passing through the pore. The results from the study on the basic characteristic of nano-emulsion and filtering test will be expected to play as the important role for the fabrication of the stable nano-emulsion or the research on the recovery of residual oil in porous media.

• Journal of Dairy Science and Biotechnology
• /
• v.32 no.2
• /
• pp.93-100
• /
• 2014

In general, whey obtained from various cheese batches is being reused, so as to improve the texture and to increase the yield and the nutrient value of the various final milk-based products. In fact, re-usage of whey proteins, including whey cream, is a common and routine procedure. Unfortunately, most bacteriophages can survive heat treatments such as pasteurization. Hence, there is a high risk of an increase in the bacteriophage population during the cheese-making process. Whey samples contaminated with bacteriophages can cause serious problems in the cheese industry. In particular, the process of whey separation frequently leads to aerosol-borne bacteriophages and thus to a contaminated environment in the dairy production plant. In addition, whey proteins and whey cream reused in a cheese matrix can be infected by bacteriophages with thermal resistance. Therefore, to completely abolish the various risks of fermentation failure during re-usage of whey, a whey treatment that effectively decreases the bacteriophage population is urgently needed and indispensable. Hence, the purpose of this review is to introduce various newly developed methods and state-of-the-art technologies for removing bacteriophages from contaminated whey and whey products.

• The Korean Journal of Pharmacology
• /
• v.22 no.2
• /
• pp.79-87
• /
• 1986

Recently it has been shown that central dopaminergic system regulates the renal function and that intracerebroventricularly (icv) administered dopamine (DA) produces antidiuresis and antinaturiuresis, resembling icv norepinephrine, and evidence has been accumulated which would suggest the involvement of adrenergic system in the DA effects. It was attempted therefore in this study to see whether the DA effect is influenced by pretreatment of yohimbine which is known as a specific ${\alpha}_2-adrenoceptor$ antagonist. Yohimbine produced, when given icv in doses of $100\;{\mu}g/kg$, marked antidiuresis and antinatriuresis along with decreases in renal perfusion and glomerular filtration. DA, in doses of $15\;{\mu}g/kg$, also produced antidiuresis and antinaturiuresis. However, after yohimbine-pretreatment DA $15\;{\mu}g/kg$ improved renal hemodynamics, and electrolyte excretion and urine flow rate transiently increased. With $150\;{\mu}g/kg$ DA, the antidiuresis was more marked in the control group. But the yohimbine-pretreated animals responded with marked diuresis and natriuresis, sodium excretion increasing more than three-fold, which lasted for 20 minutes. $K^+-excretion$, osmolar clearance as well as free-water reabsorption increased. Renal hemodynamics improved partly. Apomorphine, a DA agonist, when given icv in doses of $150\;{\mu}g/kg$, produced diuresis and naturiuresis, concomitant with increased renal hemodynamics. Yohimbine-pretreatment however did not abolish the apomorphine-induced diuresis and naturiuresis. Antidiuresis and antinatriuresis elicited by norepinephrine, $10\;{\mu}g/kg$, was not affected by yohimbine-pretreatment. These results indicate that the renal effects of icv DA is not so simple as those of norepinephrine, and the diuretic natriuretic cffect which had been masked by the hemodynamic effect becomes manifest only when the decreases in hemodynamics were removed by the pretreatment of yohimbine. It was further suggested that those DA receptors which mediate the natriuretic response to icv DA is not affected by yohimbine, whereas those receptors involved in the decrease in renal hemodvnamics are blocked by yohimbine. And the possibility of involvement of adrcnergic system in the DA action is not substantiated.

• Applied Biological Chemistry
• /
• v.22 no.3
• /
• pp.160-165
• /
• 1979

This study was carried out to investigate effects of iron content on the quality of soy sauce, bean paste and red pepper paste, and to elucidate the origin of iron and change of the contents during production processes. For the first step, the iron contents in commercial soy sauce and changes of the contents during brewing process were determined. The results obtained were as follows. 1, Iron contents of raw materials were 108 ppm in soy bean, 133ppm in defatted soy bean, 79 ppm in wheat, 5 ppm in sodium chloride, 58 ppm in seed koji, 300-2000 ppm in spore of Aspergillus oryzae, 240 ppm in wheat gluten, 20 ppm in sodium carbonate (above figures were of dry weight basis), 6 ppm in hydrochloric acid, 18 ppm in caramel and 0.3ppm in brewing water respectively. 2, Iron contents in koji were 200-240 ppm (as dry weight basis) and increased, more or less, in progress of koji-making period. 3. Iron contents in the mashes during fermentation were 40 rpm after 1 month, 43-47 ppm after 3 months and 49-62ppm after 6 months. 4. In chemical soy sauce, the iron content was 159 ppm after hydrolysis of wheat gluten with hydrochloric acid, and 184 ppm after neutralization. 5. Higher iron contents were detected both in fermented and chemical soy sauce when the concentration of total nitrogen increased, but the levels were higher in chemical soy sauce than in fermented one at the same concentration of total nitrogen. 6. In the case of fermented soy sauce, the iron content in the filtrate was decreased by press-filtration, but no significant change was found between before and after heat-sterilization. 7. Iron contents in commercial soy sauce were varied with the producers, however, the average value was 62.7 ppm as calculated as 1.0 percent of total nitrogen. And the average level of iron in home-made soy sauce produced by conventional method was 37.68 ppm.