• 연구논문집
• /
• s.30
• /
• pp.147-157
• /
• 2000

The filtered vacuum arc source (FVAS), which is adopted by magnetic filtering methode to remove the macro-particle in vacuum arc plasma, was composed of a torus structure with bending angle of 60 degree. The radius of torus was 266 mm, the radius of plasma duct was 80 mm and the total length was 600 mm. The magnet parts were consisted of one permanent magnet, one magnetic yoke and five solenoid magnets. The plasma duct was electrically isolated from the ground so that a bias voltage could be applied. The baffles inside plasma duct were installed in order to prevent the recoil effect of macro-particles. Graphite was used as the cathode material to coat the amorphic diamond film and its diameter was 80 mm. The amorphic diamond film attracts much attention due to its excellent mechanical, optical and tribological properties suitable for wide range of applications. The effects of solenoid magnet in plasma extraction were studied by computer simulation and experiment using Taguchi's method. The source and extraction magnet affected the arc stabilization. The extraction beam current was maximized with low value of the source magnet current and high value of the filtering magnet current. Optimum deposition condition was obtained when the currents of arc discharge, source, extraction, bending, deflection and outlet magnet were 30 A, 1 A, 3 A, 5 A, and 5 A, respectively.

• Tribology and Lubricants
• /
• v.38 no.3
• /
• pp.101-108
• /
• 2022

The structure and properties of tetrahedral amorphous carbon (ta-C) coatings depend on the main process parameters and bending angles of the magnetic field filter used in the filtered cathodic vacuum arc (FCVA). During the process, it is possible to effectively control the plasma flux of carbon ions incident on the substrate by controlling the arc discharge current, thereby influencing the mechanical properties of the coating film. Furthermore, we can control the size and amount of large particles mixed during carbon film formation while conforming with the bending angle of the mechanical filter mounted on the FCVA; therefore, it also influences the mechanical properties. In this study, we consider tribological characteristics for filtered bending angles of 45° and 90° as a function of arc discharge currents of 60 and 100 A, respectively. Experiment results indicate that the frictional behavior of the ta-C coating film is independent of the bending angle of the filter. However, its sliding wear behavior significantly changes according to the bending angle of the FCVA filter, unlike the effect of the discharge current. Further, upon changing the bending angle from 45° to 90°, abrasive wear gets accelerated, thereby changing the size and mixing amount of macro particles inside the coating film.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.214-214
• /
• 2013

Diamond like carbon(DLC) 박막은 고경도, 저마찰, 내스크래치 특성을 요구하는 표면기술 응용분야에 널리 사용되며, 대면적 저가 코팅 방법 개발 및 물성 조절 기술이 요구된다. 본 연구에서는 Filtered Vacuum Arc (FVA)를 통해 증착되는 Hydrogen-free DLC 박막의 밀착력 제어를 위한 증착시 기판 전압에 따른 증착 및 밀착력 특성을 분석하였다. 기판전압이 0~-150 V 까지 변화함에 따른 스크래치 테스트 결과를 통해 최적 증착 조건을 도출하였다.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.363-367
• /
• 2012

DLC (diamond liked carbon) coating of the tungsten carbide (WC) alloy core surface for molding a glass aspheric lens improves the quality of glass lens and the molding core and is characterized by high hardness, high elasticity, abrasion resistance and chemical stability. In this study, the effect of DLC coating of a thin film by means of the filtered AIP (arc ion plating) technique was examined on Ra and shape of the coated surface. Roughness before and after DLC coating was measured and the result showed that the roughness was improved after coating as compared to before coating. It was observed that DLC coating of the WC alloy core surface for molding had an effect on improving the roughness and shape of the core surface. It is considered that this will have an effect on improving abrasion resistance and the service life of the core surface.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.2
• /
• pp.53-61
• /
• 2021

The properties of tetrahedral amorphous Carbon (ta-C) film can be determined by multiple parameters and comprehensive effects of those parameters during a deposition process with filtered cathodic vacuum arc (FCVA). In this study, Taguchi method was adopted to design the optimized FCVA deposition process of ta-C for improving deposition efficiency and mechanical properties of the deposited ta-C thin film. The influence and contribution of variables, such as arc current, substrate bias voltage, frequency, and duty cycle, on the properties of ta-C were investigated in terms of deposition efficiency and mechanical properties. It was revealed that the deposition rate was linearly increased following the increasing arc current (around 10 nm/min @ 60 A and 17 nm/min @ 100A). The hardness and I_D/I_G showed a correlation with substrate bias voltage (over 30 GPa @ 50 V and under 30 GPa @ 250 V). The scratch tests were conducted to specify the effect of each parameter on the resistance to plastic deformation of films. The analysis on variances showed that the arc current and substrate bias voltage were the most effective controlling parameters influencing properties of ta-C films. The optimized parameters were extracted for the target applications in various industrial fields.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.170.2-170.2
• /
• 2016

DLC(Diamond like Carbon)는 Diamond와 유사한 물리화학적 특성을 보유한 막으로 고경도 및 우수한 내마모성, 화학적 안정성의 특성을 가지고 있다. DLC는 크게 카본의 막 형성 공정에서 카본 소스에 따라 수소가 포함된 DLC와 무수소DLC로 구분된다. Tetrahedral amorphous carbon (ta-C) 박막은 DLC 박막 중에서 가장 다이아몬드와 유사한 특성을 가지는 박막으로, a:C-H에 비해 높은 열적안정성, 경도(50~60 GPa) 및 내마모 특성이 우수하여, 현재 다양한 응용분야에 적용하고 있다. 본 연구에서는 무수소 DLC 형성을 위해 자장필터가 장착된 Filtered Vacuum Arc Source(FVAS)를 자체적으로 개발하여 연구를 진행하였다. FVAS 장비는 카본 이온 발생부와 Plasma Duct 부위, 전자석부위 구성되어 있으며, 본 연구에서는 Plasma Duct 부위의 Bias 제어를 통해 음극에서 기판으로 이동하는 카본이온의 에너지와 flux 변화를 통한 박막 증착 거동 및 물성 연구를 진행하였다. Plasma Duct Bias 변화는 각 0, 5, 10, 15, 20 V 조건으로 진행하였으며, 물성 평가는 경도(Hardness), 마찰계수, 응력(Stress), 전기전도 특성에 대한 분석을 진행하였다. 박막의 증착 거동에서는 Plasma Duct bias 변화에 따라10 V에서 가장 높은 증착 거동을 가지다 감소하는 경향을 확인 하였으며, 박막의 물성 특성 평가 시에도 이와 유사하게 특성의 차이를 관찰하였다. 이는 음극부위에서 형성된 카본이온이 기판에 도달 시에 Plasma Duct Bias 변화에 따라 이온의 Flux 및 에너지 변화로 인해 박막의 밀도 및 ta-C 막의 물성 변화로 예상되며, 이를 분석하기 위해 라만분석 및 기판 도달 에너지 분석을 진행하였다

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.54-54
• /
• 2011

The demand for low-friction, wear and corrosion resistant components, which operate under severe conditions, has directed attentions to advanced surface engineering technologies. The Filtered Vacuum Arc Cathode Deposition (FVACD) process has demonstrated atomically smooth surface at relatively high deposition rates over large surface areas. Preparation of Ti-Si-C-N nanocomposite coatings on (100) Si and stainless steel substrates with tetramethylsilane (TMS) gas pressures to optimize the film preparation conditions. Ti-S-C-N coatings were characterized using X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, nanoindentation, Rockwell C indentation and ball-on-disk wear tests. The XRD results have confirmed phase formation information of TiSiCN coatings, which shows mixing of TiN and TiC structure, corresponding to (111), (200) and (220) planes of TiCN. The chemical composition of the film was investigated by XPS core level spectra. The binding energy of the elements present in the films was estimated using XPS measurements and it shows present of elemental information corresponding to Ti2p, N1s, Si 2p and C1. Film hardness and elastic modulus were measured with a nano-indenter, and film hardness reached 40 GPa. Tribological behaviors of the films were evaluated using a ball-on-disk tribometer, and the films demonstrated properties of low-friction and good wear resistance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.157-157
• /
• 2011

Graphene has generated significant interest in the recent years as a functional material for electronics, sensing, and energy applications due to its unique electrical, optical, and mechanical properties. Much of the considerable interest in graphene stems from results obtained for samples mechanically exfoliated from graphite. Practical applications, however, require reliable and well-controlled methods for fabrication of large area graphene films. Recently high quality graphene layers were fabricated using chemical vapor deposition (CVD) on nickel and copper with methane as the source of the carbon atoms. Here, we report a simple and efficient method to synthesize graphene layers using solid carbon source. Few-layer graphene films are grown using filtered vacuum arc source (FVAS) technique by evaporation of carbon atom on Ni catalytic metal and subsequent annealing of the samples at 800$^{\circ}$C. In our system, carbon atoms diffuse into the Ni metal layer at elevated temperatures followed by their segregation as graphene on the free surface during the cooling down step as the solubility of carbon in the metal decrease. For a given annealing condition and cooling rate, the number of graphene layers is easily controlled by changing the thickness of the initially evaporated amorphous carbon film. Based on the Raman analysis, the quality of graphene is comparable to other synthesis methods found in the literature, such as CVD and chemical methods.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.2
• /
• pp.80-85
• /
• 2010

The surfaces of WC-Co and SCM415 were etched to form a micro size protrusion for oil based ultra low friction applications using an ion bombardment process in a filtered vacuum arc plasma. WC-Co species showed that a self-patterned surface was available by the ion bombarding process due to the difference of sputtering yield of WC and Co. And the increasing rate of roughness was 0.6 nm/min at -600 V substrate bias voltage. The increasing rate of roughness of SCM415 species was 1.5 nm/min at -800 V, but the selfpatterning effect as shown in WC-Co was not appeared. When the SCM415 species pretreated by electrical discharge machining is etched, the increasing rate of roughness increased from 1.5 nm/min to 40 nm/min at -800 V substrate bias voltage and the uniform surface treatment was available.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.138-138
• /
• 1999

자장 여과 진공 아크법(Filtered Vacuum Arc :FVA)에 의해 증착된 비정질 다이아몬드 박막은 기계적, 광학적 특성이 매우 우수하여 많은 연구자들의 관심의 대상이 되어 왔다. 그러나 아크의 불안정성은 자장 여과 아크 소스의 연속적인 운전을 제한하고, 결과적으로 낮은 생산성을 가져왔다. 본 연구에서는 음극의 형태 및 음극 부근에서의 자기장의 구조를 음극 부식 거동의 관점에서 수치모사 및 실험을 통해서 조사하였다. 소스 전자석과 인출 전자석의 자극 방향이 평행하게 된 구조에서 (magnetic mirror configuration), 음극 후면에 반대 방향의 자극을 가지는 영구자석을 돔으로서 아크 불안정성을 억제할 수 있었다. 또한 소스 전자석에 진동하는 전류를 인가함으로써 아크 스팟의 운동 면적을 효과적으로 확장할 수 있었다. 시간 변화에 따른 빔 전류의 변화로부터 테이프형 음극이 우물형 음극에 비하여 더 안정하다는 것을 확인하였다. 진동하는 소스 전자석의 전류와 직경 80mm의 테이퍼형 음극을 사용하여, 아크 전류 60A에서 약 2000분 동안 사용하였으며, 이때 부식된 부피는 사용 가능한 음극 부피의 약 90%였다. 그리고 약 350mA의 안정한 빔 전류를 현재의 조건에서 얻었다.