• Applied Biological Chemistry
• /
• v.40 no.2
• /
• pp.117-122
• /
• 1997

The conditions of cold storage of Citrus unshiu Marc. var. miyagawa produced in Cheju were investigated. Compared to the citrus fruits stored at room temperature, the content of soluble solids, total sugar, vitamin C and specific gravity decreased slightly on the fruits stored at $4^{\circ}C$ and 87% relative humidity. Decay ratio and weight loss were below 10% on keeping freshness relatively till late of March during cold storage. Weight loss, decrease of firmness and soluble solids occured gradually during cold storage. Nevertheless seal-packaging with 0.02 mm LDPE film or wax-coating of citrus fruits were effective on weight loss and appearance, decay ratio increased for long-term storage. It was needed to control humidity in cold chamber for preventing from decay and weight loss. Edible part ratio was decreased gradually by respiration, and peel and tissue of fruits were softened slightly by 60 days of cold storage. Decay ratio and weight loss of full-ripened citrus fruits were little during the storage for 100 days, compared to the fruits harvested early. Appearance and taste of citrus fruits stored for 4 month were good relatively, but decay occured rapidly on seal-packaging fruits putting out of cold room for a few days. Because of the difficulty of long-term storage for early variety of Citrus unshiu, the conditions and periods of cold storage would be determined after considering the physicochemical properties of fruits.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.672-679
• /
• 2013

$Fe_4[Fe(CN)_6]_3$ coated on a mica or $TiO_2$/mica surface as infrared reflective blue pigment was prepared by a hydrothermal method. $Fe_4[Fe(CN)_6]_3$, used as coloring agent, was uniformly coated on mica or $TiO_2$/mica under the optimized condition of a 1.2 : 1 weight ratio between iron(III) chloride hexahydrate and potassium ferrocyanidetrihydrate at the initial pH level of 4.5 at $70^{\circ}C$. The infrared (IR)-reflective pigments were characterized by SEM, Zeta-potenial, FT-IR, and UV-VIS NIR spectrophotometry. Especially the CIE color coordinate and total solar reflectance(TSR) properties of the pigments were investigated in relation to variation of the coating and coated substrate thicknesses. Isolation-heat paint was prepared with 20 wt% blue pigments fully dispersed in acryl-urethane resin and several additives to coat the film uniformly. The films were also measured with CIE color coordinate, TSR, and the surface temperature was recorded by an isolation-heat measuring system. The pigments and films of $Fe_4[Fe(CN)_6]_3$ coated on mica and $TiO_2$/mica showed high TSR values compared with the TSR value of $Fe_4[Fe(CN)_6]_3$ itself. According to the increase of TSR value, the property of isolation-heat is effective. To realize the optimal blue color, we applied the the pigment to $TiO_2$ coated mica(TM(b)) which has blueish interference color. The pigment of $Fe_4[Fe(CN)_6]_3$ coated on TM(b) shows a strong blue color compared with that of $Fe_4[Fe(CN)_6]_3$ coated on $TiO_2$/Mmca(TM(w)), which has a whitish interference color.

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.398-402
• /
• 2000

Three kinds of $Al_3Ti-Cr$ alloys, namely, $Al_{67}Ti_{25}Cr_8,\;Al_{66}Ti_{24}Cr_{10}\;and\;Al_{59}Ti_{26}Cr_{15}$, were prepared by induction melting followed by the thermomechanical treatment. The corrosion behavior in 3.5% NaCl solution and the high-temperature oxidation behavior at 1000, 1100 and $1200^{\circ}C$ for the prepared alloys were investigated. Electrochemical results indicated increased resistance to localized corrosion with increasing Cr content. Cr additions were found to prevent passive film from undergoing brittle fracture. XPS results revealed the passive films of $Al_3Ti-Cr$ alloys were composed mainly of $Al_2O_3$ that coexisted with $TiO_2$ and $Cr_2O_3$. The overall oxidation resistance of the prepared alloys were excellent. Specifically, the oxidation resistance increased in the order of $Al_{59}Ti_{26}Cr_{15},\;Al_{66}Ti_{24}Cr_{10}\;and\;Al_{67}Ti_{25}Cr_8$. As the Al content in the base alloys increased, the $Al_2O_3$ formation was facilitated leading to the increased oxidation resistance.

• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.36-43
• /
• 2000

In oder to enhance the selectivity of TMA(trimethylamine) gas, the ZnO-based films which were doped with $Al_2O_3$, $TiO_2, $In_2O_3$ and $V_2O_5$ catalysts with various weight percents were deposited in oxygen by RF magnetron sputtering method. To improve electrical stability of sensors, the ZnO-based films were annealed in oxygen at $700^{\circ}C$ for 1 hour. The TMA selectivity of sensors was defined by the magnitude($S_{TMA}/S_{DMA}$ and $S_{TMA}/S_{NH3}$) of TMA sensitivity relative to DMA and sensitivity ammonia($NH_3$) sensitivity, respectively. The $ZnO+Al_2O_3(4\;wt.%)+TiO_2(1\;wt.%)+In_2O_3(1\;wt.%)$ sensor showed high $S_{TMA}/S_{DMA}$ of 5.9 and $S_{TMA}/S_{NH3}$ of 26 to 160 ppm at the working temperature of $300^{\circ}C$ respectively.

• Journal of Sensor Science and Technology
• /
• v.12 no.3
• /
• pp.103-111
• /
• 2003

A chromel-alumel thermoelectric flow sensor using $Si_3N_4/SiO_2/Si_3N_4$ thermal isolation membrane was fabricated. Temperature coefficient of resistance of thin film Pt-heater was about $0.00397/^{\circ}C$, and Seebeck coefficient of chromel-alumel thermocouple was about $36\;{\mu}V/K$. The sensor showed that thermoelectric voltage decreased as thermal conductivity of gas increased, and $N_2$-flow sensitivity increased as heater voltage increased or the distance between heater and thermocouple decreased. When heater voltage was about 2.5 V, $N_2$-flow sensitivity and thermal response time of the sensor were about $1.5\;mV/sccm^{1/2}$ and 0.18 sec., respectively. Linear range in flow sensitivity of the flow sensor was wider than that of Bi-Sb flow sensor.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.250-254
• /
• 2006

Reaction of $CO_2$ with $Li_{2}ZrO_{3}$ has been investigated in a TGA and the effects of $H_{2}$ and CO on the removal of $CO_{2}$ using $Li_{2}ZrO_{3}$ were evaluated in a packed bed reactor. The initial rate of $CO_{2}$ removal reaction of $Li_{2}ZrO_{3}$ increased with the increase of gas flow rate up to 100 mL/min and then was maintained, which implied the disappearance of the gas film resistance. The reaction of $CO_{2}$ with $Li_{2}ZrO_{3}$ took place as the first order and the range of optimum temperature was found to be about $500{\sim}600^{\circ}C$. XRD and SEM analysis showed the formation of crystalline $Li_{2}ZrO_{3}$ and porous $Li_{2}ZrO_{3}$/$ZrO_{2}$. The presence of $H_{2}$ did not affect the adsorption of $CO_2$ with $Li_2ZrO_3$. On the other hand, CO inhibited the sorption of $CO_{2}$ into $Li_{2}CO_{3}$(L) on $Li_{2}ZrO_{3}$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2391-2400
• /
• 2015

Weather proof steels are used for steel bridges due to its high corrosion resistance under atmospheric conditions. However, instead of forming stabilized rust layers, general rust occurs on weather proof steels under high humidity condition close to seawater or shady places. In Japan, therefore, they perform rust stabilization treatment instead of unpainted treatment due to severe atmospheric conditions. However, most of domestic weather proof steels were constructed unpainted in the form of closed box-girder, which makes the periodical repetition of dry and wet hard to occur. For the steel bridges constructed on the Han river, the evaporation of water, dew condensation due to temperature change, and stagnant water due to rain affect harmfully on the formation of passive film on weather proof steels. Thus, in this research, in order to analyze corrosion properties inside the closed box-girder for the unpainted weather proof steel bridge in the waterworks safety zone, multiple ways of analysis such as observation with eyes, cellophane-tape test, steel thickness measurement, surface corrosion potential measurement, electron microscope analysis, and X-ray diffraction analysis of the rust were performed. As a result, unstable rust layer was observed inside the closed box-girder, and severe corrosion was observed on the top and bottom of the flanges due to the effects of stagnant water caused by rain, dew condensation, and de-icing materials.

• Horticultural Science & Technology
• /
• v.17 no.6
• /
• pp.737-741
• /
• 1999

We surveyed the physiological disorders of fruit vegetables grown in the greenhouse in Kyungbuk province in 1998. Greenhouses used for cultivation were mostly single or multi-span iron pipe houses covered with polyethylene film. Single span greenhouses were used for strawberry, oriental melon and watermelon. Fifty six percent of the surveyed farms was a mono-cropping system for oriental melon and tomato. There were greenhouses used for successive cultivation for 10 years or more for strawberry and oriental melon in Koryeong and Seongju. Varieties of fruit vegetables cultivated were diverse, especially in cucumber and watermelon. In strawberry, malformed fruits were observed most frequently in March and the small fruits at late harvest period. Leaf chlorosis, stunt plants and runner outbreak were also found during the growing season. In tomato, occurrence of malformed fruits was severe from March to May, and occurrence of cracked fruits and blossom- end rot was also severe in October and November. The self topping and abnormal stem in tomato were problem in hydroponic cultures in August and November, respectively. Malformed cucumber fruits, such as curved, club shaped, irregular shaped and narrow necked, occurred at late season. Umbrella-shaped leaf in cucumber in summer were caused by calcium deficiency. Most serious disorders were fermented and malformed fruits occurring from March to May in oriental melon, and cracked fruits occurring from April to May in watermelon. At late growing stage of melons the leaf chlorosis occurred with complex symptoms of leaf disease. Growers had little knowledge on physiological disorders, and also on diagnose and measures to cure the disorders. Most growers pointed out that poor soil environment and temperature management in the greenhouse as the main causes of physiological disorders.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.3
• /
• pp.284-294
• /
• 2006

Statement of problem. Proliferation of Candida albicans is primarily within the plaque on the fitting surface of the denture rather than on the inflamed mucosa. Consequently, the treatment of the denture is equally important as treatment of the tissue. Cleansing and disinfection should be efficiently carried-out as the organisms can penetrate into the voids of the acrylic resin and grow in them, from which they can continue to infect and reinfect bearing tissues. Purpose. The purpose of this study was to evaluate the applicability of photocatalytic reaction to eliminate Candida albicans from acrylic resin denture base, and to investigate the anti-fungal effect with various UVA illumination time. Materials and Methods. The specimens were cured by the conventional method following the manufacturer's instruction using thermal polymerized denture base resin (Vertex RS: Dentimex, Netherlands). $TiO_2$ photocatalyst sol(LT), which is able to be coated at normal temperature, was made from the Ti-alkoxide progenitor. The XRD patterns, TEM images and nitrogen absorption ability of the $TiO_2$ photocatalyst sol(LT) were compared with the commercial $TiO_2$ photocatalyst P-25. The experimental specimens were coated with the mixture of the $TiO_2$ photocatalyst sol(LT) and binder material (silane) using dip-coater, and uncoated resin plates were used as the control group. Crystallinity of $TiO_2$ of the specimen was tested by the XRD. Size, shape and chemical compositions were also analyzed using the FE-SEM/ EDS. The angle and methylene blue degradation efsciency were measured for evaluating the photocatalytic activity of the $TiO_2$ film. Finally, the antifungal activity of the specimen was tested. Candida albicans KCTC 7629(1 ml, initial concentration $10^5$ cells/ ml) were applied to the experiment and control group specimens and subsequently two UVA light source with 10W, 353 nm peak emission were illuminated to the specimens from 15cm above. The extracted $2{\mu}l$ of sample was plated on nutrient agar plate ($Bacto^{TM}$ Brain Heart Infusion; BD, USA) with 10 minute intervals for 120 minute, respectively. It was incubated for 24 hours at $37^{\circ}C$ and the colony forming units (CFUs) were then counted. Results. Compared the characteristics of LT photocatalyst with commercial P-25 photocatalyst, LT were shown higher activity than P-25. The LT coated experimental specimen surface had anatase crystal form, less than 20 nm of particle size and wide specific surface area. To evaluate the photocatalytic activity of specimens, methylene blue degradation reaction were used and about 5% of degradation rate were measured after 2 hours. The average contact angle was less than $20^{\circ}$ indicating that the LT photocatalyst had hydrophilicity. In the antifungal activity test for Candida albicans, 0% survival rate were measured within 30 minute after irradiation of UVA light. Conclusion. From the results reported above, it is concluded that the UVA-LT photocatalytic reaction have an antifungal effect on the denture surface Candida albicans, and so that could be applicable to the clinical use as a cleaning method.

• Korean Journal of Materials Research
• /
• v.23 no.3
• /
• pp.155-160
• /
• 2013

ZnO thin films co-doped with Mg and Ga (MxGyZzO, x + y + z = 1, x = 0.05, y = 0.02 and z = 0.93) were prepared on glass substrates by RF magnetron sputtering with different sputtering powers ranging from 100W to 200W at a substrate temperature of $350^{\circ}C$. The effects of the sputtering power on the structural, morphological, electrical, and optical properties of MGZO thin films were investigated. The X-ray diffraction patterns showed that all the MGZO thin films were grown as a hexagonal wurtzite phase with the preferred orientation on the c-axis without secondary phases such as MgO, $Ga_2O_3$, or $ZnGa_2O_4$. The intensity of the diffraction peak from the (0002) plane of the MGZO thin films was enhanced as the sputtering power increased. The (0002) peak positions of the MGZO thin films was shifted toward, a high diffraction angle as the sputtering power increased. Cross-sectional field emission scanning electron microscopy images of the MGZO thin films showed that all of these films had a columnar structure and their thickness increased with an increase in the sputtering power. MGZO thin film deposited at the sputtering power of 200W showed the best electrical characteristics in terms of the carrier concentration ($4.71{\times}10^{20}cm^{-3}$), charge carrier mobility ($10.2cm^2V^{-1}s^{-1}$) and a minimum resistivity ($1.3{\times}10^{-3}{\Omega}cm$). A UV-visible spectroscopy assessment showed that the MGZO thin films had high transmittance of more than 80 % in the visible region and that the absorption edges of MGZO thin films were very sharp and shifted toward the higher wavelength side, from 270 nm to 340 nm, with an increase in the sputtering power. The band-gap energy of MGZO thin films was widened from 3.74 eV to 3.92 eV with the change in the sputtering power.