• Journal of Practical Agriculture & Fisheries Research
• /
• v.20 no.1
• /
• pp.175-185
• /
• 2018

This study was conducted to evaluate the physiological and ecological characters of rice cultivars suitable for low fertilized condition. 5 rice cultivars(Jinmibyeo, Sobibyeo, Hwayeongbyeo, Nagdongbyeo and Junambyeo) were cultivated for selection under 3 different nitrogen application levels, and 1 cultivars were selected. The results obtained are summarized as follows ; High yielded rice cultivars under low N application level were Junambyeo, Jinheng and Sobibyeo. Also these cultivars were yielded highly under conventional level(11kg/10a). Milled rice yield under conventional level(11kg/10a) was positively correlated with them under low N levels. Milled rice yield was most affected by no. of grain/m². Rice cultivars that were high crop growth rate(CGR) before heading stage were Junambyeo, Sobibyeo and Nagdongbyeo. Grain filling rate was increased mostly until 20 days after heading, and decreased after this stage. Nitrogen use efficiency was higher under low N level(5.5kg/10a) than conventional level(11kg/10a). Especially, Junambyeo was most low in Apparent recovery of applied N(AR) under low N application level, but most high in Agronomic N use efficiency(ANUE). This characteristics of Junambyeo will to be useful for selection of variety suitable for growing under low fertilized condition.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.1
• /
• pp.102-109
• /
• 2024

In order to use limestone powder as a material for concrete, the mechanical and durability characteristics of cement matrices manufactured by varying the substitution rate were evaluated. In general, limestone powder did not contribute to the cement hydration reaction, so as a result of the compressive strength test of cement mortar using it, the compressive strength decreased as the substitution rate increased. However, as a result of evaluating the durability performance of cement mortar using limestone powder, such as chloride ion penetration resistance, carbonation resistance, and chemical attack resistance, small particles of limestone powder showed superior results compared to the unsubstituted control mortar due to the micro-filler effect of filling the fine pores inside the cement matrix. Therefore, limestone powder is expected to be used as an effective method for improving the durability of concrete. In this study, the durability was evaluated by changing the mixing amount of limestone powder to 0 %, 5 %, 10 %, and 15 %, but it is judged that it is necessary to study in more detail the effect on the durability by changing the end and mixing amount of limestone powder to various levels in the future.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.1
• /
• pp.23-29
• /
• 2020

Purpose: The purpose of this retrospective study was to evaluate the method using the S-reamer and gel-type graft material by the success rate and survival rate. Materials and methods: Implantation period was from 2008 to 2014, Follow check up year is 2019. There were 59 patients and 117 implants. All implants were placed in the posterior maxilla with the sinus lift. The patients population consisted of 34 men and 25 women, ranging from 19 to 75 years. The residual bone heights were from 1 mm to 6 mm. Sinus was perforated with S-reamer without membrane tearing and gel type bone graft material was used for membrane lifting and filling the space. all implants were placed simultaneously. Panoramic X-ray was taken. After 5 - 6 months healing period, final prostheses were restored. After more 5-years implant surgery, Panoramic X-ray was obtained and X-ray analysis and clinical examination were performed. Success criteria was referred to a Buser's success critera. All implants were classified to success implant, survival implant, failed implant. A success implant was satisfying success criteria, a survival implant was a implant that was acute infection with suppuration and bone loss, a failed implant was a implant that was mobile, removed. Results: Five implants were removed, and 4 implants had infected with bone loss. Survival rate was 95.7% and success rate was 92.3%. Conclusion: This retrospective study presented that this method with S-reamer and gel-type graft material was a successful treatment without membrane tear in the condition of 1-6 mm residual bone height.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.723-729
• /
• 2019

Turbochargers are an effective device to reduce the fuel consumption. In this study, the mass flow rate of pulsating flow in the twin-scroll turbocharger for the gasoline engine of passenger vehicles was measured. Pulsating flow was achieved using a pulse generator and the mass flow rate of the unsteady pulsating flow was analyzed by comparing it with those of the steady flow. The pulse generator consisted of a rotating upper plate and a fixed lower plate. To measure the mass flow rate of unsteady flow, the orifice flow meter equipped with the difference pressure transducer was used. To analyze the low speed performance of the turbocharger, the measurement was carried out in the speed of turbocharger from 60,000rpm to 100,000rpm. The mass flow parameters of the unsteady pulsating flow showed a large difference compared to those of the steady flow. Those of the unsteady flow showed the hysteresis loop surrounding the mass flow parameters of the steady flow and the maximum variation of the mass flow parameters were 5.0 times those of the steady flow. This phenomenon is the result of the filling and emptying the turbine volute space due to pulsating flow.

• Korean Journal of Food Science and Technology
• /
• v.27 no.3
• /
• pp.404-413
• /
• 1995

System parameters (extrusion temperature, extrusion pressure, specific mechanical energy, mean residence time) were analysed on three different screw configurations during twin-screw extrusion of wheat bran. Experiments were conducted over a screw speed of $280{\sim}380\;rpm$, feed rate of $22{\sim}38\;kg/hr$ and moisture content of $17{\sim}33%$ using screws assembled with 3, 4, and 5 reverse screw elements (RSE) adjacent to the heating zone of the barrel. Extrusion temperature increased with increasing RSE but it decreased with increasing feed rate and moisture content. Decreasing the filling ratio of the screw resulted in a lower extrusion pressure, and increasing the length of the RSE gave similar results due to the higher temperature and lower viscosity of melted dough. It was also observed that increasing the feed rate and decreasing moisture content resulted in the reduced extrusion pressure. Specific mechanical energy (SME) decreased when the feed rate and moisture content increased, and SME increased when using RSE posses from 3 to 5. Screw configuration posses with 4 RSE yielded the longest RT, and the smaller the die hole, the higher the RT. In contrast, RT decreased when the feed rate increased. With increasing moisture content RT for 3 RSE increased, but that for 4 and 5 RSE decreased.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.482-489
• /
• 2020

This study conducted a prototype development and evaluation by performing die-casting mold design, mold manufacturing, and injection condition optimization based on flow and solidification analysis to meet the needs of the coupling parts produced by die casting. Through flow analysis, the injection conditions suitable for 100% filling in the cavity were found to be a molten metal temperature of 670 ℃, injection speed of 1.164 m/s, and filling pressure of 6.324~18.77 MPa. In addition, solidification close to 100 % occurred in all four cavities when the solidification rate was 69.47 %. A defect inspection on the surface and inside the product revealed defects, such as poor molding and pores. In addition, the dimensions of the injected product were within the target tolerance and showed good results. Through the feedback of the results of flow and solidification analysis, it was possible to optimize the mold design, and the injection optimization conditions were confirmed to be a total cycle time of approximately 6.5 seconds. Good quality carrier parts with an average surface hardness of approximately 45 mm from the gate measured at 97.48(Hv) could be produced.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.238-238
• /
• 2017

Salt stress is one of the deteriorating abiotic stresses due to the climate change, which causes over-accumulation of $Na^+$ and $Cl^-$ ions in plants and inhibits the growth and yield of rice especially in coastal Southeastern Asia. The yield components of rice plant (panicle number, spikelet number per panicle, 1000-grain weight, % of ripened grains) that are majorly affected by salt stress vary with growth stages at which the plant is subjected to the stress. In addition, the salt sensitivity of each yield component differs among rice varieties even when the salt-affected growth stage was same, which indicates that the physiological mechanism to maintain each yield component is different from each other. Therefore, we hypothesized that rice plant has different genes/QTLs that contribute to the maintenance of each yield component. Using a Japanese leading rice cultivar, Koshihikari, and salt-tolerant Nona bokra's chromosome segment substitution lines (CSSLs) with the genetic background of Koshihikari (44 lines in total) (Takai et al. 2007), we screened higher yielding CSSLs under salinity in comparison to Koshihikari and identified the yield components that were improved by the introgression of chromosome segment(s) of Nona bokra. The experiment was conducted in a salinized paddy field. One-month-old seedlings were transplanted into a paddy field without salinity. These were allowed to establish for one month, and then the field was salinized by introducing saline water to maintain the surface water at 0.4% salinity until harvest. The experiments were done twice in 2015 and 2016. Although all the CSSLs and Koshihikari decreased their yield under salinity, some CSSLs showed relatively higher yield compared with Koshihikari. In Koshihikari, all the yield components except panicle number were decreased by salinity and % of ripened grains was mostly reduced, followed by spikelet number per panicle and 1000-grain weight. When compared with Koshihikari, keeping a higher % of ripened grains under salinity attributed to the significantly greater yield in one CSSL. This indicated that the % of ripened grains is the most sensitive to salt stress among the yield components of Koshihikari and that the Nona bokra chromosome segments that maintained it contributed to increased yield under salt stress. In addition, growth analyses showed that maintaining relative growth rate in the late grain filling stage led to the increased yield under salt stress but not in earlier stages.

• Korean Journal of Remote Sensing
• /
• v.31 no.2
• /
• pp.149-160
• /
• 2015

A comparative study was conducted for alternative consecutive procedures of detection of cloud-contaminated pixels and gap-filling and smoothing of time-series data to produce high-quality gapless satellite vegetation index (i.e. Normalized Difference Vegetation Index, NDVI). Performances of five alternative methods for detecting cloud contaminations were tested with ground-observed cloudiness data. The data gap was filled with a simple linear interpolation and then, it was applied two alternative smoothing methods (i.e. Savitzky-Golay and Wavelet transform). Moderate resolution imaging spectroradiometer (MODIS) data were used in this study. Among the alternative cloud detection methods, a criterion of MODIS Band 3 reflectance over 10% showed best accuracy with an agreement rate of 85%, which was followed by criteria of MODIS Quality assessment (82%) and Band 3 reflectance over 20% (81%), respectively. In smoothing process, the Savitzky-Golay filter was better performed to retain original NDVI patterns than the wavelet transform. This study demonstrated an operational framework of gapdetection, filling, and smoothing to produce high-quality satellite vegetation index.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.30 no.1
• /
• pp.93-100
• /
• 1985

Five winter and five spring wheat cultivars of diverse genetic backgrounds were evaluated to examine different developmental responses in terms of stages of the life cycle and grain yield when grown under the different planting dates. Greatest difference in growth and developmental patterns of the winter and spring wheat cultivars occurred in stem elongation, booting, inflorescence emergence and anthesis. The growth stage of stem elongation was found to exhibit larger difference both among planting dates and cultivars. Winter wheat cultivars responded more than spring wheat cultivars to the different planting dates. Winter wheat 'Cho Kwang' and spring wheat 'Jugoku 81' were earlier and exhibited faster growth and development, while winter wheats 'Yamhill' and 'Hyslop' were later in growth and development, but exhibited faster grain filling and higher rate of grain filling, resulting in higher grain yields. Crosses between winter and spring wheat gene pools would result in earlier maturity and higher productivity for both winter and spring wheat cultivars. For developing early maturing wheat cultivars for multiple cropping sequences while maintaining productivity, selection for earliness trait should be started at the stem elongation stage. Furthermore, the breeding materials should be planted at several times for selection of shorter life cycle genotypes adaptable to the cropping sequences. This is due to the genotype x planting date interactions.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.9 no.3
• /
• pp.70-76
• /
• 2001

Proper design and improvement of the biofiltration process depend upon quantitative understanding of the kinetic behavior in the biofilter. This study was conducted to evaluate kinetics of biofiltration of gasoline vapor. Filling material of the biofilter was compost. Gas inlet concentration ranged from about $300mg/m^3$ to $7,000mg/m^3$. Gas velocities were 6m/hr and 15m/hr, respectively. At 6m/hr gas velocity, about 60% of gasoline TPH below $3,000mg/m^3$ was removed in the lower quarter part of the biofilter. First order kinetics described well the degradation rate of gasoline TPH with high correlation. First order kinetic removal constant at the gas velocity of 6m/hr was higher than that of 15m/hr from about $300mg/m^3$ to $7,000mg/m^3$. When the inlet concentration was over $3,000mg/m^3$, first order kinetic removal constant at the gas velocity of 6m/hr was over twice that at 15m/hr. In order to obtain over 80% of removal efficiency, gasoline vapor should be injected into the biofilter at concentration below about $2,000mg/m^3$, 100cm filling height and the gas velocity of 6m/hr.