• Journal of Energy Engineering
• /
• v.21 no.3
• /
• pp.243-248
• /
• 2012

In this study, The report analysed the characteristics of power drop and damage of surface in solar cell through high temperature and humidity test. The solar cells were tested during the 1000hr in $85^{\circ}C$ temperature and 85% humidity conditions, that excerpted standard of PV Module(KS C IEC-61215). An analysis of the cell surface through EL(Electroluminescence), the cell has partly change of surface in yearly. Single-crystalline Solar cell efficiency is decreased from 17.7% to 15.6% and decreasing rate is 11.9%. On the other hand, Poly-crystalline Solar cell efficiency is decreased from 15.5% to 14.0% and decreasing rate is 9.3%. A comparison of the fill factor for analysis of electro characteristic in yearly, Single-crystalline Solar cell efficiency is decreased from 78.7% to 78.1% and decreasing rate is 4.7%. On the other hand, Poly-crystalline Solar cell efficiency is decreased from 78.1% to 76.7% and decreasing rate is 1.8%. Single-crystalline has more bigger power drop than poly-crystalline by the silicon purity and silicon atom arrangement. Also, FF decreasing rate has more bigger drop than efficiency decreasing rate for the reason that the damage of surface by exterior environmental factor is the more influence in cell than other reason that is decreasing FF by damage of p-n junction.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.166-168
• /
• 2004

Conventional Switched Mode Power Supplies(SMPS) with diode-capacitor rectifier have distorted input current waveform with high harmonic order contents. Typically, these SMPS have a power factor lower than 0,7. To improve with this problem the power factor correction(PFC) circuit of power supplies has to be introduced. Specially, to the reduce size and manufacture cost of power conversion device, the single-stage PFC converter is increased to demand as necessary of study. In this paper, comparative analysis of Valley-fill, boost and feedforward type single stage power factor correction circuit based on the flyback converter is given. Also, the validity of designed three type of single stage PFC circuit are confirmed by simulation and experimental results.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 1999.11a
• /
• pp.179-184
• /
• 1999

To fill the emotivity in the interior design, the functional factor from the provided space, the aesthetic factor including modeling factor, and even the practical factor from the convenience and the value must be considered. To carry out an achieved design by the emotivity, it must follow the recognition of the original function which comes from the emotivity design method, and it should be applied to the design process fitting into the purpose of the space. The value of the sufficient interior by the emotivity is depended on what kind of image it gives, and how much of the satisfaction it can give to the customers. And fur more, it should not be partially lean to any of the decoration and the function of the object. That is, how faithfully it was to the use and the purpose of the interior and the emotion related to all parts which are the functional side and the decorative side mainly considered in the external form is designed by the essential part of the design.

• Journal of Biosystems Engineering
• /
• v.11 no.2
• /
• pp.55-65
• /
• 1986

The resistance to the passage of airflow through various agricultural products is an important consideration in the design of an aeration or drying system. The amount of resistance to airflow varied widely from one kind of grain to another, and depended upon airflow rate, surface texture and shape of the particles, the size and configuration of voids, and foreign and fine material in the grain bed. The airflow rate was the major factor considered on this kind of study in the early stages. But these days, the studies on the resistance to airflow of grain affected by grain moisture content and foreign and fine material have been widely carried out. However the foreign an fine material in the grain bed could not be a major factor on the study in Korea because there were only a few grain process procedure after harvesting it. The objectives of this study were to investigate the effect of moisture content and airflow rate on airflow resistance to grain, and to develop a model to predict the static pressure drop across the grain bed as a function of moisture content and airflow rate. The rough rice varieties, Akibare, Milyang 15 (Japonica types), Samkwang, Backyang (Indica types)and covered barley variety, Olbori, which were harvested in 1985 were used in the experiment after cleaning them. Resistances to airflow of grain were investigated at four levels of moisture content (13-25%, wb.) for ten different airflow rates($0.01-0.15m^3/sm^2$). The results of this study are summarized as follows; 1. Theaverage bulk densities were $585.3kg/m^3$ for rough rice and $691.6kg/m^3$ for barley at the loose fill, and were $648.8kg/m^3$ for rough rice and $758.2kg/m^3$ for barley at the packed fill. The pressure drops at the packed fill beds were approximately 1.4 to 1.8 times higher than those at the loose fill beds. 2. The pressure drops across grain beds deceased with the increase of moisture content and increased with airflow rate. The decreasing rates of pressure drop across grain beds according to the moisture contents at the lower airflow rates were higher than those at the higher airflow rates, and the increasing rates of pressure drop according to the airflow rates at the lower moisture contents were higher those at higher moisture contents. 3. The pressure drop across barley bed were much higher than rough rice beds and the pressure drops across Japonica type rough rice beds were a little higher than Indica type. 4. The mathematical models to predict the pressure drop across grain beds as a function of moisture content and airflow rate were developed from these experiments.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.3
• /
• pp.485-490
• /
• 2012

In this paper, driver circuit of LED lights for ships is designed and implemented to replace conventional lights with filament which have short life time due to vibration of ships. The driver of LED module is switching circuit without transformer to reduce volume and cost. As switch circuit controls input 220 VAC with PWM, LED module is reliably driven. Power factor is improved by using valley-fill PFC compensation circuit which is handled to pulse current of switching circuit. Serial-parallel LED circuit is applied to reduce change period of lights of long-term navigation ships. Array of serial-parallel can operate even if some of LEDs is damaged. It is suitable for ships that power consumption and power factor of lights including developed drive circuit have 39Watt and 0.925 respectively.

• Korean Journal of Materials Research
• /
• v.27 no.10
• /
• pp.518-523
• /
• 2017

In commercial solar cells, the pattern of the front electrode is critical to effectively assemble the photo generated current. The power loss in solar cells caused by the front electrode was categorized as four types. First, losses due to the metallic resistance of the electrode. Second, losses due to the contact resistance of the electrode and emitter. Third, losses due to the emitter resistance when current flows through the emitter. Fourth, losses due to the shading effect of the front metal electrode, which has a high reflectance. In this paper, optimizing the number of finger on a $4{\times}4$ solar cell is demonstrated with known theory. We compared the short circuit current density and fill factor to evaluate the power loss from the front metal contact calculation result. By experiment, the short circuit current density($J_{sc}$), taken in each pattern as 37.61, 37.53, and $37.38mA/cm^2$ decreased as the number of fingers increased. The fill factor(FF), measured in each pattern as 0.7745, 0.7782 and 0.7843 increased as number of fingers increased. The results suggested that the efficiency(Eff) was measured in each pattern as 17.51, 17.81, and 17.84 %. Throughout this study, the short-circuit current densities($J_{sc}$) and fill factor(FF) varied according to the number of fingers in the front metal pattern. The effects on the efficiency of the two factors were also investigated.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1159-1162
• /
• 2007

We have developed $16{\mu}m{\times}16{\mu}m$ digital micromirror array suitable for seamless-picture projection display system. This structure can improve the picture quality by making seamlesspicture image when combined with high-fill-factor microlens array to focus lights onto the mirror center. The fabricated micromirror shows excellent dynamic performances including the resonant frequency of 400 kHz.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.272-273
• /
• 2003

제조기술이 발전함에 따라 비구면을 사용한 광학계 설계에 대한 많은 연구가 보고 되고 있다. 본 연구에서는 단일렌즈에서 다양한 렌즈면 조합 중에서 성능이 가장 우수하게 나타난 비구회절면(비구면과 회절면을 동시에 적용)을 사용하여 이군렌즈에 대해 F／l.0인 대구경 광학계를 설계하였다. 사용된 검출기 사양은 픽셀 크기 45um, 픽셀 수 320$\times$240 이며, fill factor 는 무시하였다. 광학계의 유효초점거리는 171.73mm 이며, 사용한 프로그램은 ORA 사의 Code V 이다. (중략)

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3298-3300
• /
• 1999

In this paper, a $10{\times}10$ micro SLM array for phase and amplitude modulation of incident light is designed and fabricated using surface micromachining technology. Hidden spring structure is used in order to maximize the fill-factor and minimize diffraction effect at the support posts. Static and dynamic characteristics of designed micro SLM are simulated with ABAQUS and measured with optical measurement system using He-Ne laser and PSD(position sensitive devise).

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.07a
• /
• pp.142-143
• /
• 2003

제조기술이 발전함에 따라 회절 복합 렌즈(diffractive hybrid lens)를 사용한 광학계 설계에 대한 많은 연구가 보고 되고 있다. 본 연구에서는 회절 복합 렌즈를 사용한 F／l.0인 광학계를 설계하여 비열화 특성을 분석하였다. 성능조건으로는 MTF가 50% 일 때 사용된 영상센서의 Nyquist 주파수인 11.11cys／mm로 하였다. 사용된 검출기 사양은 픽셀 크기 45um, 픽셀 수 320$\times$240 이며, fill factor 는 무시하였다. 광학계의 유효초점거리는 171.73mm 이다. (중략)