• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.1
• /
• pp.70-75
• /
• 2011

We introduced nanoscale interfacial layers between the PV layer and the cathode in poly (3-hexylthiophene):methanofullerene bulk-heterojunction polymer photovoltaic (PV) cells. The nanoscale double interfacial layers were made of ultrathin poly (oxyethylenetridecylether) surfactant and low-work-function alloy-metal of Al:Li layers. It was found that the nanoscale interfacial layers increase the photovoltaic performance, i.e., increasing short-circuit current density and fill factor with improved device stability. For PV cells with the nanoscale double interfacial layers, an increase in power conversion efficiency of $4.18{\pm}0.24%$ was achieved, compared to that of the control devices ($3.89{\pm}0.08%$) without the double interfacial layers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.343-344
• /
• 2008

A surface micromachined uncooled microbolometer based on the amorphous silicon was designed, fabricated, and characterized. We designed the microbolometer with a pixel size of $44\times44{\mu}m^2$ and a fill factor of about 50 % ~ 70% by considering such important factors as the thermal conductance, thermal time constant, the temperature coefficient of resistance, and device resistance. Also, we successfully fabricated the microbolometer by using surface MEMS technology. Finally, we investigated responsivity and detectivity properties depends on the active area size.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2003.05a
• /
• pp.1142-1149
• /
• 2003

Various organizational factors effect successful implementation of IT enabled business transformation. Among them, the most critical success factor is deemed to overcoming change management problem. Lots of studies have been made on Implementation methodologies and business process formalizations to encourage organizational members to accept new business process changes. However, the logic or process redesign still depends on qualitative problem solving techniques mostly depending on basically human intuition such as brainstorming. cause-and-effect analysis. and so on. In this paper, we focused on developing analytic framework to design to-be business process structure. which can complement qualitative problem solving procedures. With effective use of IT as an enabler, we provide algorithmic framework applicable to designing various business process changes such as process automation, business process resequencing, and more radical process integration. The framework follows dynamic programming approach in the literature, which is based on the decision making paradigm of organizations to abstract business processes as quantitative decision models. As such, our research ran fill the gap of limited development of theory based analytic methodologies for business process design, by providing objective rationale to reach the consensus among the organizational members including senior management.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.289-290
• /
• 2006

We report a study of Zn(S)Se/GaAs heterojunction solar cells grown by molecular beam epitaxy (MBE). Zn(S)Se/GaAs heterostructures prepared under different conditions were characterized in-situ by reflection high-energy electron diffraction (RHEED). Structural and electrical properties were investigated with double crystal X-ray diffraction and current-voltage characteristics, respectively. The fabricated $n-ZnS_{0.07}Se_{0.93}/p-GaAs$ solar cell (SC #2) exhibited open circuit voltage($V_{oc}$) of 0.37 V, short circuit current($I_{sc}$) of $1.7{\times}10^{-2}$ mA, fill factor of 0.62 and conversion efficiency of 7.8 % under 38.5 $mW/cm^2$ illumination.

• Proceedings of the IEEK Conference
• /
• 2000.11c
• /
• pp.153-156
• /
• 2000

A novel silicon retina chip based on the information processing in the vertebrate retina was designed. The chip has a novel wiring structure in which all pixels are connected through the channel of MOS transistors, which simplifies a wiring structure compared with conventional resistive networks. The proposed structure minimizes the pixel area and certainly increases a fill factor since each pixel consists of only two photodiodes and three MOS transistors. It also enables the chip to operate over a wide range of light intensity by adjusting its conductance with the gate voltage. Simulation results with SPICE showed that the chip could extract the edge of input images successfully.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.618-620
• /
• 1997

A $50{\times}50{\mu}m^2$ aluminum micromirror array is fabricated using shadow evaporation process. The fabrication process is very simple with use of shadow evaporation process, and the micromirror array has a high fill-factor. The static and dynamic characteristics such as deflection angle vs. applied voltage, step response, and frequency response are measured using a contact free optical measurement technique. The downward threshold voltage was 8 V, step response time was $13.5{\mu}s$ when 32 V step voltage applied, and a resonance observed at 11kHz. The lifetime of micromirror with anti-stiction coating was tested and micromirror operated successfully over 200 million cycles of touch-down operations.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.12
• /
• pp.2436-2440
• /
• 2009

In this work, TCO-less dye-sensitized solar cells (DSCs) using Ti-mesh layer is fabricated for high-efficient low-cost solar cell application. The Ti-mesh metal can replace TCO in the photo-electrode part of DSCs, thus the cell structure is composed of a glass/dye sensitized TiO2 particle/ Ti-mesh layer/electrolyte/Pt sputtered counter electrode/ glass. The Ti-mesh electrode with high conductivity can collect electrons from the $TiO_2$ layer and allows the ionic diffusion of $I^-/I_3^-$ through the mesh hole. Thin Ti-mesh ($\sim40{\mu}m$ in thickness) electrode material is processed using rapid prototype method. The efficiency of prepared TCO-less DSCs sample is about 1.45 % ((ff: 0.5, Voc: 0.52V, Jsc: 5.55 $mA/cm^2$).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.441-441
• /
• 2014

The characteristics of hybrid conductive films based on multilayer graphene and silver grid have been investigated for the high-performance and flexible organic solar cells. The hybrid conductive films have been prepared on glass and polyethylene terephthalate (PET) substrates using conventional photolithography process and transfer process of graphene. The optical and electrical properties of prepared conductive films show transmittance of 87% at 550nm and sheet resistance of $28{\Omega}/square$. The electromechanical properties were also investigated in detail to confirm the flexibility of the hybrid films. OSCs have been fabricated on the hybrid conductive films based on graphene and silver grid on glass substrate. The power conversion efficiency of 2.38%, a fill factor of 51%, an open circuit voltage of 0.58V and a short circuit current of $8.05mA/cm^2$ were obtained from the device on glass substrate. The PCE was enhanced 11% compared with OSCs on the MLG films without silver grid.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.349-349
• /
• 2014

ITO는 결정질 실리콘 태양전지의 anti-reflection coating (ARC) 층으로써 적합한 물질이다. ARC layer로써 구조적, 전기적 그리고 광학적 최적 조건의 특성을 얻기 위해는 높은 figure of merit(FOM)를 가져야 하고 결정방향 제어를 해야 한다. 본 연구에서는 결정질 실리콘 태양전지에 가장 적합한 ITO ARC layer의 특성 찾기 위해 Radio frequency magnetron sputter를 이용하여 공정 조건가변 실험을 진행 하였으며 높은 FOM을 갖는 ITO 반사방지막을 shallow emitter형 결정질 실리콘 태양전지에 적용하였으며 ITO 박막은 shallow emitter층과 완벽한 ohmic 접합을 이루었다. ITO ARC layer를 적용한 Shallow emitter형 태양전지는 81.59%의 fill factor와 $35.52mA/cm^2$의 단락전류를 보이며 17.27%의 광변환 효율을 보였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.216-220
• /
• 1994

Polycrystalline CdS films have been prepared by coating a slurry, which consisted of CdS, 11w% CdCl$_2$ and appropriate amount of propylene glycol, on glass substrate and glass substrate coated with indium tin oxide(ITO) followed by sintering in a nitrogen atmosphere. CdTe slurries consisting of Te powder and Cd powder were coated on the sintered CdS films and ITO/CdS films and were sintered in nitrogen to prepare sintered CdS/CdTe and ITO/CdS/CdTe solar cells. The value of fill factor increased due to low series resistance and open circuit voltage decreased due to low shunt resistance in the ITO/CdS/CdTe solar cells.