• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.735-737
• /
• 2003

A superconducting motor consisting of high temperature superconducting (HTS) rotor and air-core stator is under development in Korea Electrotechnology Research Institute. HTS motor was designed for having the rated power of 100hp at 1800 rpm. HTS field winding is composed of sixteen HTS race track shaped coils wound with stainless steel-reinforced Bi-2223 tape conductor by react and wind fabrication method. Nomex Paper was used for electrical insulation. Each of four magnet pole assemblies was constructed with four double pancake sub-coils, mechanically stacked and electrically in series. Four magnet assemblies were fixed on an aluminum support structure to make effective heat transfer. Critical current (Ic) of HTS field winding was 41A but minimum Ic of sub-coils was 35A at 77K and self field. Joule heat generated in HTS field winding was 2.11W at 77K and 35A.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.297-299
• /
• 2002

To wind a HTS (High Temperature Superconductor) tape conductor on a bobbin, double pancake winding technique is widely used to reduce number of splicing contacts between conductor pieces. However, this makes some Ic (critical current) degradation on kink points which is unavoidable. This paper describes the two ways of winding; usual double pancake and soldered double pancake. Characteristics of the two windings are measured and compared.

• 전기의세계
• /
• 제21권6호
• /
• pp.9-16
• /
• 1972

This work intends to study the machine dynamics in the state-space approah and to formulate the operating characteristics of a namplidyne generator, with balanced control field winding and an auxiliary feedback winding for compensating purpose. In the derivation of the dynamic equation, investigations on the demagnetization effects are accentuated, based on the magnetic interlinks between windings of the machine. From the machine dynamic relation obtained, a state-variable representation of the machine dynamics is approached in the first part of this work.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2000년도 KIASC Conference 2000 / 2000년도 학술대회 논문집
• /
• pp.177-179
• /
• 2000

In this paper, we analyzed quench characteristics of field windings using 2 dimensional analysis. The quench origin was assumed to take place at the inner most point in the mid-plane of the coil. The temperature distribution was numerically calculated on the coil cross section using FDM analysis, and was used to estimate the normal zone resistance of the coil. Finally, we obtained voltage current characteristics of the quenched winding coils.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.116-118
• /
• 2001

This paper deals with characteristic analysis of a slotless PM linear motor using analytical method. In order to calculate voltage equations, back-EMF waveform and winding inductance are caculated by PM's magnetic field and winding's magnetic field respectively.

• Journal of Electrical Engineering and Technology
• /
• 제7권5호
• /
• pp.730-735
• /
• 2012

This paper presents a method to design the waveform of a back electromotive force (back EMF) of an axial flux permanent magnet (AFPM) motor using printed circuit board (PCB) windings. When the magnetization distribution of permanent magnet (PM) is given, the magnetic field in the air gap region is calculated by the quasi three dimensional (3D) space harmonic analysis (SHA) method. Once the flux density distribution in the winding region is determined, the required shape of the back EMF can be obtained by adjusting the winding distribution. This can be done by modifying the distance between patterns of PCB to control the harmonics in the winding distribution. The proposed method is verified by finite element analysis (FEA) results and it shows the usefulness of the method in eliminating a specific harmonic component in the back EMF waveform of a motor.

• 전기의세계
• /
• 제24권1호
• /
• pp.55-62
• /
• 1975

A single-phase induction motor with it's stator winding splitted into two series windings, of which the terminals of one winding is switched pulsationally by a thyristor type ON-OFF device so that the motor may operate as a pulsational shaded-pole motor, can modulate current waveforms of it's two series windings. In view of current waveform modulation method, a single-phase single-winding motor operates as a two-phase induction motor with asymmetrical axis windings where the starting torque can be obtained effectively without an auxiliary capacitor attached and it's running speed controlled by shifting phase between current waveforms differently. Equivalent circuit for analysis is modified from a double revolving field equivalent circuit of a single-phase induction motor with asymmetrical windings whose angle is 45.deg.C elet. degrees. Analysis and test results show that ON-OFF action of the pulsational shaded-pole winding has the same effect of a series capacitor, and then at heavy loads this motor operates with a small amonut of the input current than that having the fixed shaded-pole winding.

• 조명전기설비학회논문지
• /
• 제25권5호
• /
• pp.15-21
• /
• 2011

This paper presents an analyzing method of the capacitance of the power transformer for initial voltage distribution and insulation design. When a high incoming surge voltage is accidently occurred in windings of transformer, it does not distribute equally in the windings. This phenomenon makes electric field concentration and the insulating material could be break. Initial voltage distribute mostly depends on capacitances between winding to winding or winding to core in the transformer. If the C network can be structuralized into the equivalent circuit model and be calculated each capacitance element value by circuit analysis and FEM(Finite Element Method) simulation program, the transformer designer could know the place where the structure is to be modified or the insulation to be reinforced. This method quickly provides the data of the voltage distribution in each winding to the designer.

• 한국초전도ㆍ저온공학회논문지
• /
• 제5권1호
• /
• pp.97-101
• /
• 2003

When HTS tapes are used in power application, they are used by winding form, such as, a pancake and a solenoid. When AC current is applied to the coil, Ac magnetic field is generated in winding. This AC magnetic field acts as an external magnetic field and makes loss. In this paper the radial magnetic field component ($B_r$) and the axial magnetic field component ($B_z$) in a pancake and a solenoid were calculated by numerical analysis method and compare with measured value. AC losses of a short sample were calculated by Norris equation and n numerical analysis based on Brandt equation. AC losses of the pancake coil and the solenoid coil were also calculated.

• 전기학회논문지
• /
• 제57권11호
• /
• pp.1970-1975
• /
• 2008

Critical current of the superconducting machines is limited by the magnetic field. When the magnetic field is not uniform, it is difficult to estimate the magnetic field and the critical current. This paper proposed a method for the estimation of the magnetic field and the critical current of the HTS pancake windings which can be used to generate the high field magnet. A parameter which was needed to calculate the critical current of a BSCCO magnet with 10 pancake windings was obtained by the experiment. Test which was carried out by using single pancake winding and magnet consisting of 10 pancake windings shows the proposed method can be an effective method for the estimation of the critical current of pancake windings.