• Structural Engineering and Mechanics
• /
• 제85권1호
• /
• pp.29-53
• /
• 2023

High-strength shielding concrete against gamma radiation is a priority for many medical and industrial facilities. This paper aimed to investigate the gamma-ray shielding properties of high-strength hematite concrete mixed with silica fume (SF) with nanoparticles of lead dioxide (PbO₂), tungsten oxide (WO₃), and bismuth oxide (Bi₂O₃). The effect of mixing steel fibres with the aforementioned binders was also investigated. The reference mixture was prepared for high-strength concrete (HSCC) containing 100% hematite coarse and fine aggregate. Thirteen mixtures containing 5% SF and nanoparticles of PbO₂, WO₃, and Bi₂O₃ (2%, 5%, and 7% of the cement mass, respectively) were prepared. Steel fibres were added at a volume ratio of 0.28% of the volume of concrete with 5% of nanoparticles. The slump test was conducted to workability of fresh concrete Unit weight water permeability, compressive strength, splitting tensile strength, flexural strength, and modulus of elasticity tests were conducted to assess concrete's engineering properties at 28 days. Gamma-ray radiation of 137Cs emits photons with an energy of 662 keV, and that of 60Co emits two photons with energies of 1173 and 1332 keV were applied on concrete specimens to assess radiation shielding properties. Nanoparticles partially replacing cement reduced slump in workability of fresh concrete. The compressive strength of mixtures, including nanoparticles was shown to be greater, achieving 94.5 MPa for the mixture consisting of 7.5 PbO2. In contrast, the mixture (5PbO₂-F) containing steel fibres achieved the highest values for splitting tensile, flexural strength, and modulus of elasticity (11.71, 15.97, and 42,840 MPa, respectively). High-strength shielded concrete (7.5PbO2) showed the best radiation protection. It also showed the minimum concrete thickness required to prevent the transmission of radiation.

• Computers and Concrete
• /
• 제22권3호
• /
• pp.337-353
• /
• 2018

The present study focuses on examining the structural behaviour of steel-fibre-reinforced concrete (SFRC) beams under high rates of loading largely associated with impact problems. Fibres are added to the concrete mix to enhance ductility and energy absorption, which is important for impact-resistant design. A simple, yet practical non-linear finite-element analysis (NLFEA) model was used in the present study. Experimental static and impact tests were also carried out on beams spanning 1.3 meter with weights dropped from heights of 1.5 m and 2.5 m, respectively. The numerical model realistically describes the fully-brittle tensile behaviour of plain concrete as well as the contribution of steel fibres to the post-cracking response (the latter was allowed for by conveniently adjusting the constitutive relations for plain concrete, mainly in uniaxial tension). Suitable material relations (describing compression, tension and shear) were selected for SFRC and incorporated into ABAQUS software Brittle Cracking concrete model. A more complex model (i.e., the Damaged Plasticity concrete model in ABAQUS) was also considered and it was found that the seemingly simple (but fundamental) Brittle Cracking model yielded reliable results. Published data obtained from drop-weight experimental tests on RC and SFRC beams indicates that there is an increase in the maximum load recorded (compared to the corresponding static one) and a reduction in the portion of the beam span reacting to the impact load. However, there is considerable scatter and the specimens were often tested to complete destruction and thus yielding post-failure characteristics of little design value and making it difficult to pinpoint the actual load-carrying capacity and identify the associated true ultimate limit state (ULS). To address this, dynamic NLFEA was employed and the impact load applied was reduced gradually and applied in pulses to pinpoint the actual failure point. Different case studies were considered covering impact loading responses at both the material and structural levels as well as comparisons between RC and SFRC specimens. Steel fibres were found to increase the load-carrying capacity and deformability by offering better control over the cracking process concrete undergoes and allowing the impact energy to be absorbed more effectively compared to conventional RC members. This is useful for impact-resistant design of SFRC beams.

• Geomechanics and Engineering
• /
• 제9권4호
• /
• pp.415-426
• /
• 2015

Researches have been done to discover ways to strengthen peat soil deposits. In this model study, fibrous peat that is the most compressible types of peat has been reinforced with precast peat columns stabilized with ordinary Portland cement and polypropylene fibres. Rowe cell consolidation tests as well as plate load tests (PLTs) were conducted on various types of test samples to evaluate the strength and deformation of untreated peat and peat reinforced by various types of columns. PLTs were conducted in a specially designed and fabricated circular steel test tank. The compression index ($C_c$) and recompression index ($C_r$) of fibrous peat samples reduced considerably upon use of precast columns. Also, PLT results confirmed the results obtained from Rowe cell tests. Use of polypropylene fibres added to cement further decreased ($C_c$) and ($C_r$) and increased load bearing capacity of untreated peat. Finite element method (FEM) using Plaxis 3D was carried out to evaluate the stress distributions along various types of tested samples and also, to compare the deformations obtained from FEM analysis with the actual maximum deformations found from PLTs. FEM results indicate that most of the induced stresses are taken on the upper portion of tested samples and reach their maximum values below the loading plate. Also, a close agreement was found between actual deformation values obtained from PLTs and values resulted from FEM analysis for various types of tested samples.

• Carbon letters
• /
• 제4권3호
• /
• pp.111-116
• /
• 2003

Carbon/carbon composites were developed using PAN based carbon fibres and phenolic resin as matrix in different volume fractions and heat treated to temperatures between $1000^{\circ}C$ to $2500^{\circ}C$. Although both the starting precursors are nongraphitizing hard carbons individually, their composites lead to very interesting properties e.g. x-ray diffractograms show the development of graphitic phase for composites having fibre volume fractions of 30~40%. Consequently the electrical resistivity of such composites reaches a value of $0.8\;m{\Omega}cm$, very close to highly graphitic material. However, it was found that by increasing the fibre volume fraction to 50~60%, the trend is reversed. Optical microscopy of the composites also reveals the development of strong columnar type microstructure at the fibre (matrix interface due to stress graphitization of the matrix. The study forcasts a unique possibility of producing high thermal conductivity carbon/carbon composites starting with carbon fibres in the chopped form only.

• The Korean Journal of Pain
• /
• 제13권2호
• /
• pp.247-250
• /
• 2000

Recently, some authors reported that discogenic low back pain should be regarded as a referred pain in respect of neural pathway. The afferent pathways of discogenic low back pain is transmitted mainly by sympathetic afferent fibres from the sinuvertebral nerves in the second lumbar nerve root. This pain arises from the lumbar intervertebral discs, and it had been transmitted mainly through the sympathetic afferent fibres contained in the second lumbar spinal nerve root. Second lumbar dermatome corresponds to the low back area. We experienced a case of low back pain which could not be controlled by conventional therapy and progressed wax and wane. The CT finding showed bulging disc between $L_4$ and $L_5$ and spinal stenosis in $L_4$ area. And epiduroscopic feature showed severe adhesion in $L_4$, $L_5$ and $S_1$. After we blocked $L_2$ root, pain score decreased 10 to 2. Therefore, the $L_2$ root block may be a useful diagnostic procedure as well as provide therapeutic value.

• 펄프종이기술
• /
• 제42권2호
• /
• pp.95-101
• /
• 2010

For the development of higher-sizing performance of paper, a sizing agent using recycled PET was synthesised. Polyester resin was extracted from wasted PET by subcritical hydrolysis and finally modified to synthetic sizing agent by mixing water-disperse PET with triphenyl phosphite(TPP). The modified PET was considered as an internal sizing agent in different wet-end papermaking conditions. The optimum condition in sizing efficiency was obtained in initial pH of 6.5 in case of rosin+alum system, and 7.5 in case of rosin+alum+PET system, respectively, and in addition amount of PET 3%. The sizing efficiency was also closely related according to the fiber properties of wet-end slurry, such as virgin fibres from UKP and recycled fibres from KOCC. The application of modified PET was good in strength improvement of paper, specially in tensile strength.

• 한국환경과학회지
• /
• 제13권9호
• /
• pp.799-806
• /
• 2004

The filtration tests were made in cell with a low concentrated suspension. The suspension with a concentration of $C_{M}$=1.14～2.67$\cdot$$10^{-3}$ g/g consists of paper paint and water. The particles in the suspension have a particle size x<1${\mu}m$. The used depth filters consists of glass fibres, which are coated by polymer. The filtration in depth filters accorded in different mechanism, which were explained by physical models. The model which would be allows to make a promise of the filtration reaction. This filter media allows to get a high filtration time and a good separation rate. The Particle distribution is measured by a photon correlation spectroscopy(PCS). PCS measures particle sizes 0.03 ${\mu}m$${\mu}m$ in the suspension. The filtered suspension has a very low concentration Co{\le}5{\times}10_{-4}$ g/g of solid in sample. The PCS also informs us about the number of the particles in the suspension. The makes it possible to calculate the concentration of the in sample.

• Composites Research
• /
• 제28권3호
• /
• pp.112-117
• /
• 2015

Mechanical properties of nonwoven alfa fiber based reinforced biocomposite were evaluated to assess the possibility of using it as a new material in engineering applications such as orthopedic application. Samples were fabricated by needle punching, thermal bonding and Hydroentanglement, by blending alfa fibers with wool fibers or Polypropylene fibers. The mechanical properties were tested and showed that the nonwoven NW3 (alfa fiber/PP/PLA, with hydroentanglement) is the best. It has a value of stress at break of 1.94 MPa, a strain of 54.2% and a young's module of 7.95 MPa, in a production normal direction. A biocomposite has been made with NW3 mixed with PMMA matrix. The use of nonwoven based alfa fiber in reinforcing the composite material increases its rigidity and the tensile strength; the elongation was found to be 1.53%, the Young's Module of 1.79 GPa and the tensile at break of 15.06 MPa. Results indicated that alfa fibres are of interest for low-cost engineering applications and can compete with glass fibres in orthopedic application.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Proceedings of Pre-symposium of the 10th ISWPC
• /
• pp.115-119
• /
• 1999

During mechanical pulp production and blcaching wood components, such as extractives, carbohydrates and lignin are dissolved and dispersed into the process waters. These components are called dissolved and colloidal substances(DCS). DCS can accumulate during water circulation and can in turn affect paper machine runnability and also the strength and optical properties of the paper. In this work DCS fraction origination from TMP process were treated with enzymes acting on triglycerides. glucomannans, and lignin and the effect of enzymatic treatments on the water composition as well as sheet properies were evaluated. Lipases were found to modify the chemical structure of the extractives resulting in more hydrophilic fibre surface and subsequent improvement in the sheet strength properties. Mannanase treatment, on the other hand, destabilized pitch. As a result, aggregation of pitch to the fibres was observed which in turn resulted in impaired strength properties. Laccase could effectively polymerize lignans and the reaction products seemed to be sorbed onto the fibres.

• 대한화장품학회:학술대회논문집
• /
• 대한화장품학회 2003년도 IFSCC Conference Proceeding Book II
• /
• pp.200-200
• /
• 2003

Intact mammalian hair and wool fibres are multi-compartmental composite materials consisting of a sulphur-rich outer protective cuticle layer surrounding elongated, highly keratinized, cortex cells. The cortex cells themselves are made up of crystalline, filamentous, low-sulphur a-helical keratin molecules embedded in a matrix of highly cross-linked, globular high-sulphur keratins. It is the structurally organised and highly disulphide cross-linked nature of these materials that provides them with their remarkable mechanical properties. However these mechanical properties are sensitive to environmental conditions such as water content, temperature and chemical treatment and the importance of their ultra-structural arrangements to overall mechanical properties in different environments is still not fully understood.(omitted)