• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.434-439
• /
• 1993

Described is a stabilizing circuit of the Doppler beat signal obtained by the coherence-dependent fiber-optic laser Doppler velocimeter (LDV), which employs both a self-mixing laser diode (SM-LD) and a 10m-100m long optical fiber. The stabilizing circuit maintains the SM-LD drive current at an optimum value, which gives a maximum Doppler signal during long hours.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.486-489
• /
• 2004

In this paper, we try to detect the peel out effect and find the strain difference between the main structure and retrofitting patch material when they separate from each other. In the experiment, two fiber optic Bragg grating sensors are applied to the main concrete structure and the patching material separately at the same position. The sensors show coincident behaviors at the initial loading, but different behaviors after a certain load. The test results show the possibility of optical fiber sensor monitoring of beam structures retrofitted by the composite patches.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.353-355
• /
• 1993

A single-mode fiber-optic interferometer for measuring small vibrations was constructed. The interferometer is based on the Fabry-Perot configuration that uses a single mode bidirectional fiber coupler as a beam splitter and employs peak detection scheme in the signal processing. The instrument was used to measure the displacement of the translator clamped to a piezo crystal.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.683-687
• /
• 1988

Digitalization of processor and increase of control information need the fiber optic data network which has excellent noise immunity and high-quality, widebaudwidth information transfer capability. It is aimed to offer a fiber optic dataway system for measuring and control the power plant, that has high reliability, high data transmission rate and small cable duct with large transmission capacity.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1874-1876
• /
• 1997

A fiber optic voltage sensor using photoelastic effect of a single-mode optical fiber, excited with a 632.8 nm He-Ne laser, is developed. The photoelastic effect is produced by piezoelectric effect for the voltage measurement. It is found that the detector output voltage is proportional to the applied voltage. Also, the frequency of the output voltage is equal to that of the applied voltage. Experimental results from a laboratory model demonstrate the feasibility of the sensor for field application in high-voltage systems.

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.02a
• /
• pp.296-297
• /
• 2004

A Signal processor for the open-loop fiber optic gyroscope(FOG) is equipped with a stabilizer to reduce the error due to drift of fiber phase modulator (FPM). The stabilizer is designed to be operated to maintain the ratio of amplitude and phase between harmonics in the FOG signal. When FPM stabilizer is used, the temperature drift of FOG is reduced to less than 0.5 deg/hr in change of 20$^{\circ}C$.

• Korean Journal of Optics and Photonics
• /
• v.4 no.4
• /
• pp.487-492
• /
• 1993

A polarization maintaining fiber optic gyroscope was constructed having an optical loss of about 25 dB. Using the earth rotation rate as a reference, the long term stability of better than $3^{\circ}/hr$ and the rms short term noise of $0.6^{\circ}/hr/{\sqrt{Hz}}$ were obtained.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.07a
• /
• pp.139-140
• /
• 2008

We demonstrate a novel acousto-optic filter using a two-mode photonic crystal fiber. Thanks to endless two-mode operation of the fiber, single notch over a whole spectrum is obtained with tuning range of> 1000 nm.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.103-109
• /
• 2009

We report an efficient jitter reduction technique in an analog fier-optic link employing a Mach-Zehnder modulator followed by an erbium-doped fiber amplifier. By adjusting the modulator-bias to $0.089V_{\pi}$, we could increase the RF gain up to 10.65 dB for 10 GHz RF signal and reduce the random jitter by 46.5%, max, at an input optical power of -0.11 dBm to the EDFA.

• Journal of Sensor Science and Technology
• /
• v.7 no.3
• /
• pp.147-153
• /
• 1998

The strain characteristics of a fiber optic Fabry-Perot pressure sensor with high sensitivity using a $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$ (N/O/N) diaphragm is experimentally investigated. A 600 nm thick N/O/N diaphragm was fabricated by silicon anisotropic etching technology in 44 wt% KOH solution. An interferometric fiber optic pressure sensor has been manufactured by using a fiber optic Fabry-Perot intereferometer and a N/O/N diaphragm. The 2 cm length fiber optic Fabry-Perot interferometers in the continuous length of single mode fiber were produced with two pieces of single mode fiber coated with $TiO_{2}$ dielectric film utilizing the fusion splicing technique. The one end of the fiber optic Fabry-Perot interferometer was bonded to a N/O/N diaphragm. and the other end was connected to an optical setup through a 3 dB coupler. For the N/O/N diaphragm sized $2{\times}2\;mm^{2}$ and $8{\times}8\;mm^{2}$, the pressure sensitivity was measured 0.11 rad/kPa and 1.57 rad/kPa, respectively, and both of the nonlinearities were less than 0.2% FS.