In this research, optical fiber sensors and shape memory alloys (SMA) were incorporated into sandwich panels for development of a smart honeycomb sandwich structure with damage detection and shape recovery functions. First, small-diameter fiber Bragg grating (FBG) sensors were embedded in the adhesive layer between a CFRP face-sheet and an aluminum honeycomb core. From the change in the reflection spectrum of the FBG sensors, the debonding between the face-sheet and the core and the deformation of the face-sheet due to impact loading could be well detected. Then, the authors developed the SMA honeycomb core and bonded CFRP face-sheets to the core. When an impact load was applied to the panel, the cell walls of the core were buckled and the face-sheet was bent. However, after the panel was heated over the reverse transformation finish temperature of the SMA, the core buckling disappeared and the deflection of the face-sheet was relieved. Hence the bending stiffness of the panel could be recovered.
This study aimed to investigate the fatigue crack growth behavior of a kind of fiber metal laminates (FML) under four different stress levels. The FML specimen consists of three 2024-T3 aluminum alloy sheets and two layers of glass/epoxy composite lamina. Tensile-tensile cyclic fatigue tests were conducted on centrally notched specimen at four stress levels with various maximum values. A digital camera system was used to take photos of the propagating cracks on both sides of the specimens. Image processing software was adopted to accurately measure the length of the cracks on each photo. The test results show that: (1) a-N and da/dN-a curves of FML specimens can be divided into transient crack growth segment, steady state crack growth segment and accelerated crack growth segment; (2) compared to 2024-T3 aluminum alloy, the fatigue properties of FML are much better; (3) da/dN-${\Delta}K$ curves of FML specimens can be divided into fatigue crack growth rate decrease segment and fatigue crack growth rate increase segment; (3) the maximum stress level has a large influence on a-N, da/dN-a and da/dN-${\Delta}K$ curves of FML specimens; (4) the fatigue crack growth rate da/dN presents a nonlinear accelerated increasing trend to the maximum stress level; (5) the maximum stress level has an almost linear relationship with the stress intensity factor ${\Delta}K$.
In this study, the development of annealing textures in cold rolled and annealed tantalum sheets was analyzed using electron backscatter diffraction. At $900^{\circ}C$, the textures of the recrystallized grains in the partially and completely recrystallized microstructures displayed significant similarities. The average diameter of the recrystallized grains with ${\gamma}-fiber$ orientations exceeded that of grains with different orientations, and the average growth rates were unrelated to the orientations after an initial stage of recrystallization. Additional cold rolling and annealing was done for controlled initial microstructures and textures inherited from various processes of prior cold rolling and annealing. This second cycle of the process resulted in stronger textures with major ${\gamma}-fiber$ orientations as a result of the enhanced ${\gamma}-fiber$ orientations in the preceding textures. A coarse-grained prior microstructure resulted in a weaker annealing texture than a fine grained one regardless of the stronger previous texture, which was occasioned by the sub-structures of the minor orientations at local deformation inhomogeneities such as sharp in-grain shear bands.
The main objective of this article is to investigate the response of different fiber metal laminates subjected to low velocity impact experimentally and numerically via finite element method (FEM). Hence, two different fiber metal laminate (FML) samples (GLARE/CARALL) are made of 7075-T6 aluminum sheets and polymeric composites reinforced by E-glass/carbon fibers. In order to study the responses to the low velocity impacts, samples are tested by drop weight machine. The projectiles are released from 1- and 1.5-meters height were the speed reaches to 4.42 and5.42 meter per second and the impact energies are measured as 6.7 and 10 Joules. In addition to experimental study, finite element simulation is done and results are compared. Finally, a detailed study on the maximum deflection, delamination and damages in laminates and geometry's effect of projectiles on the laminate response is done. Results show that maximum deflection caused by spherical projectile for GLARE samples is more apparent in comparison with the CARALL samples. Moreover, the maximum deflection of GLARE samples subjected to spherical projectile with 6.7 Joules impact energy, 127% increases in comparison with the CARALL samples in spite of different total thickness.
탄소섬유 강화 복합재료는 높은 비강도 및 비강성을 가지기 때문에 자동차 산업, 선박, 우주 항공 산업과 같은 다양한 산업 분야에 적용되어 왔으며, 수요가 점차 증가하고 있다. 탄소섬유 강화 복합재료에는 기지재로 주로 에폭시(Epoxy)와 같이 점도가 낮고 젖음 특성이 우수하며 강도가 양호한 열경화성(Thermosetting) 수지가 사용된다. 열경화성 수지는 우수한 물리적 특성을 나타내지만 재사용이 어렵다. 이러한 문제를 해결하기 위하여 재사용이 가능한 탄소섬유 강화 열가소성 수지(Thermoplastic) 복합재료 개발 및 탄소섬유 재사용에 관한 많은 연구들이 진행되고 있다. 본 연구에서는 열분해 방법을 사용하여 탄소섬유/에폭시 복합재료로부터 탄소섬유와 수지를 분리하여 탄소섬유를 재활용하였다. 에폭시의 분해도(Degree of decomposition)는 열중량분석기(TGA)와 시차 주사현미경(SEM)을 통해 확인하였다. 수지로부터 분리해낸 탄소섬유는 절단(Cutting)과 그라인딩(Grinding) 방법을 거쳐 탄소섬유 복합재료 시트(Sheet)를 제조하였다. 재활용 탄소 섬유로 제조된 탄소섬유 시트는 각각 다른 냉각조건에서 결정화 엔탈피(Crystallization enthalpy)와 기계적 특성, 표면과 단면의 형태를 분석하였다.
Kuo Lan-Sheng;Perng Yuan-Shing;Wang Eugene I-Chen;Yen Chen-Fa;Kao Tsuen-Han
한국펄프종이공학회:학술대회논문집
/
한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
/
pp.91-98
/
2006
The purpose of this study is to investigate the opacity and printing strength of MG paper overlaid plywood. The printing strength of ink on MG paper can be evaluated effectively by a formula $E^{*2}=[(L^{*})^{2}+(a^{*})^{2}+(b^{*})^{2}]^{1/2}$ that we proposed. Higher E value indicates good printing strength of ink-on-paper. We also assess the real color of translucent printed MG paper with a formula CIE ${\bigtriangleup}E^{*}$ (color difference between a pile of same paper to be opaque and fancy paper laminated board). In addition, the color difference on paper surface caused by the color of wood-based board (bottom) can be evaluated by a formula of Pc. No. Generally, an acceptable appearance quality of fancy boards is ${\bigtriangleup}E^{*}$ <2.0 and small Pc.No. value. The experimental results showed that Japan-made MG papers -J1, J2 and J3 have better printing strength and gloss than that of Taiwan-made paper (T1). The reason for this was that Taiwan-made paper has poor printing strength and low gloss, which might be correlated to the fiber compositions in paper. Higher printing strength can be seen for short fiber containing handsheets when comparing to that of handsheets. Nonetheless, low-freeness sheets gives better printing strength than that of high-freeness sheets. High-opacity MG paper gives good opacifying effect to the fancy paper laminated wood-based boards. Comparing the surface color of 2 kinds of fancy paper laminated boards, paperboard T1 laminated with high-opacity fancy paper showed slight color difference. The same results can be seen for $??g/m^{2}$ handsheets. Higher-opacity Acacia and Eucalyptus bleached sulfate pulps (short fiber) gives higher opacifying effect on the plywood when comparing to Northan pine and Radiata pine sulfate pulps(long fiber). The former ones also showed small color differences when comparing the color differences between the color of fancy paper and laminated paper board. Additionally, the color of bottom plywood can't be shown through for the high-opacify surface paper adhered to. Besides, the PC No of the base paper laminated board is small as well. Apparently, we can add colorants to the binders for the manufscture of various handsheets ($30g/m^{2}$) with various pulp mix ratios to increase the opacity of paperboards to certain extents. When we using yellow and brown binders in paper laminated board, the color difference between Acacia and Eucalyptus handsheets overlaid boards decreasing to 2.0 (acceptable ${\bigtriangleup}E^{*}$ <2.0, hard to discern), but not much improvement for Northern and Radiata pines. Definitely, show-through defects can be discernible for lower opacity papers. In general, admirable printing strength of fancy paper by which glued to plywood can be made with high-opacity paper and colored binders techniques.
국립중앙박물관 소장 대혜보각선사서는 1387년에 제작된 고려시대 서책으로 2005년 입수 되었으며 전체적인 손상이 매우 심각하였다. 이에 장황 특성과 과학적 분석을 통해 제작기법과 재료를 조사하였고 이를 토대로 전체 보존처리가 진행되었다. 서지학적 특성으로 장황형태는 오침안선장본(五針眼線裝本)이며 판식은 광곽이 사주단변(四周單邊), 계선은 무계(無界)이다. 보존처리는 기본 형태 조사 와 보존처리 과정을 살폈다. 형태는 겉표지와 원표지, 면지, 내지로 구성되어 있으며 내지는 0.04~0.07mm로 일반적인 책지에 비해 매우 얇은 특성을 보인다. 표지와 내지 모두 열화로 인한 부서짐이 심각한 상태로 판단되어 전체 해체를 통해 보존처리가 진행되었다. 보존처리는 해체-클리닝-결손부 보강-스캔-제책 과정을 거쳤으며 오동나무상자를 제작하여 보관하도록 하였다. 해체 시 내지와 책 끈의 시료를 채취하여 섬유식별을 진행하였다. 내지 섬유식별은 사프라닌과 C-stain 염색으로 식별하였다. 사프라닌 염색 결과 섬유벽이 두껍고 마디와 왜곡, 투명막이 확인되었고, C-stain 염색결과 탁한 적색을 띠고 있어 닥나무 섬유로 식별하였다. 책 끈은 단면이 편평한 원형의 형태이며 중앙부분에 루멘이 관찰되어 면섬유로 판별하였다.
Arani, Ali Ghorbanpour;Haghparast, Elham;Zarei, Hassan BabaAkbar
Steel and Composite Structures
/
제23권5호
/
pp.529-541
/
2017
In the present study, vibration analysis of functionally graded carbon nanotube reinforced composite (FGCNTRC) plate moving in two directions is investigated. Various types of shear deformation theories are utilized to obtain more accurate and simplest theory. Single-walled carbon nanotubes (SWCNTs) are selected as a reinforcement of composite face sheets inside Poly methyl methacrylate (PMMA) matrix. Moreover, different kinds of distributions of CNTs are considered. Based on extended rule of mixture, the structural properties of composite face sheets are considered. Motion equations are obtained by Hamilton's principle and solved analytically. Influences of various parameters such as moving speed in x and y directions, volume fraction and distribution of CNTs, orthotropic viscoelastic surrounding medium, thickness and aspect ratio of composite plate on the vibration characteristics of moving system are discussed in details. The results indicated that thenatural frequency or stability of FGCNTRC plate is strongly dependent on axially moving speed. Moreover, a better configuration of the nanotube embedded in plate can be used to increase the critical speed, as a result, the stability is improved. The results of this investigation can be used in design and manufacturing of marine vessels and aircrafts.
Generally, beam-column joints are taken into account as rigid in assessment of seismic performance of reinforced concrete (RC) structures. Experimental and numerical studies have proved that ignoring nonlinearities in the joint core might crucially affect seismic performance of RC structures. On the other hand, to improve seismic behaviour of such structures, several strengthening techniques of beam-column joints have been studied and adopted in practical applications. Among these strengthening techniques, the application of FRP materials has extensively increased, especially in case of exterior RC beam-column joints. In current paper, to simulate the inelastic response in the core of RC beam-column joints strengthened by FRP sheets, a practical joint model has been proposed so that the effect of FRP sheets on characteristics of an RC joint were considered in principal tensile stress-joint rotation relations. To determine these relations, a combination of experimental results and a mechanically-based model has been developed. To verify the proposed model, it was applied to experimental specimens available in the literature. Results revealed that the model could predict inelastic response of as-built and FRP strengthened joints with reasonable precision. The simple analytic procedure and the use of experimentally computed parameters would make the model sufficiently suitable for practical applications.
With respect to rehabilitation, strengthening and retrofitting of existing and deteriorated columns in buildings and bridges, CFRP sheets have been found effective in enhancing the performance of existing RC columns by wrapping and bonding CFRP sheets externally around the concrete. Concrete columns and piers that are confined by both lateral steel reinforcement and CFRP are sometimes referred to as "hybrid" concrete columns. With the availability of experimental data on concrete columns confined by steel reinforcement and/or CFRP, the study presents modeling using artificial neural networks (ANNs) to predict the compressive strength of hybrid circular RC columns. The prediction of the ultimate confined compressive strength of RC columns is very important especially when this value is used in estimating the capacity of structures. The present ANN model used as parameters for the confining materials the lateral steel ratio (${\rho}_s$) and the FRP volumetric ratio (${\rho}_{FRP}$). The model gave good predictions for three types of confined columns: (a) columns confined with steel reinforcement only, (b) CFRP confined columns, and (c) hybrid columns confined by both steel and CFRP. The model may be used for predicting the compressive strength of existing circular RC columns confined with steel only that will be strengthened or retrofitted using CFRP.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.