• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.5
• /
• pp.985-990
• /
• 2007

The method of enhancing visibility in optical fiber sensor was investigated by improving coherence length of light source. The optical feedback technique is used to enhance coherence length in fiber laser which generates laser in near infrared wavelength region and utilizes low loss characteristics of optical communication grade fiber. In this paper, the effect to coherence length by short and long optical feedback paths are investigated by using Mach-Zehnder interferometer technique. The effect to coherence length by changing optical feedback power and optical modulation are investigated. The spectral drift was calculated by measuring the degree of phase perturbation in unbalanced Mach-Zehnder interferometer having loom path difference. The short optical feedback path was effective to reduce spectral drift to 450kHz/sec and the long optical feedback path in combination with short optical feedback path was found to further reduce spectral drift to 50kHz/sec.

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.13-20
• /
• 2005

Fiber-Bragg-grating external cavity laser(FGL) modules were fabricated and experimentally analyzed. Proposed as a cost-effective solution for optical sources in the WDM-PON access network, FGL modules were packaged to TO-CAN type. We obtained a low threshold current of 13 mA, and an optical output power of 3.6 mW with a bias current of 60 mA at $25^{\circ}C$. The lasing wavelength dependencies on current and temperature were as small as 5.2 pm/mA and 30 pm/$^{\circ}C$, respectively. These change rates of the wavelength with the temperature and current are smaller than those of the DFB laser. Single-mode oscillations with the side-mode suppression ratio(SMSR) over 30 dB are maintained above the threshold current level. The FGL modules can be directly modulated at 155 Mbps, PRBS(2$^{23}$ -1) NRZ signal. Through the BER plots, we did not see the significant degradations before and after the transmission over 20km of the SMF at 155 Mb/s.

• Journal of information and communication convergence engineering
• /
• v.14 no.3
• /
• pp.147-152
• /
• 2016

In radio-over-fiber (RoF) systems, nonlinear compensation is essential to improve performance. Among the several existing nonlinear compensation techniques, we investigate a predistortion technique for a directly modulated laser in an RoF system. First, we obtain the input-to-output response of a directly modulated laser at 160, 820, and 1,540 MHz. The results show that the laser response is dependent on the frequency band. Second, we design an optimal predistortion circuit to compensate for the nonlinear responses of three frequency bands. We design the predistortion circuit with two options: each predistortion circuit for each frequency band and one single predistortion circuit for all the three frequency bands. Finally, we present the simulation results of the predistortion system obtained using a commercial simulator. These results show that the third intermodulation distortion (IMD3) is improved by 0.6-9 dB for the three frequency bands with only a single predistortion circuit.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.51-58
• /
• 2020

In this study, a novel method for sweeping automatic linearization of wavelength swept laser is proposed. Through the test performed on the implemented laser, the linear sweeping is held up well with a 97% decrease in nonlinearity, and 60 nm sweeping range, 1 kHz sweeping frequency, and 8.8 mW average optical power were obtained. The proposed method uses fiber Bragg grating array, optical-electronic conversion circuit, FPGA embedded module, and a LabVIEW program to generate new compensated wave patterns which were applied to the fiber Fabry-Perot tunable filter. Linear sweeping can reduce the cumbersome and time-consuming recalibration process required for nonlinear sweeping. Additionally, the proposed method provides more accurate measurement results for the structure safety monitoring system.

• ETRI Journal
• /
• v.24 no.3
• /
• pp.255-258
• /
• 2002

We created a new design for an Nd-doped clad-pumped silica fiber laser to enhance the pump absorption and lasing efficiency for a butt-coupled, end-pumped scheme. Two concatenated adiabatic tapers formed within the laser cavity simultaneously removed higher order modes and were spliced to conventional single mode fibers. We theoretically analyzed mode propagation along the composite cavity and experimentally achieved continuous wave oscillation in the $LP_{01}$ mode at $1.06\;{\mu}m$ and a laser output power of over 820 mW with a slope efficiency of 27%.

• Korean Journal of Optics and Photonics
• /
• v.4 no.1
• /
• pp.114-119
• /
• 1993

We constructed a laser-heated pedestal growth station using a 25 W $CO_2$ laser to grow various single crystal fibers. The LHPG system consists of the optical system which includes a reflaxicon, an elliptic mirror and a parabolic mirror with their centers drilled, and the translation system to move a source and a seed independently. To test the system, we pulled a few ruby fibers with diameter of 600 ${\mu}m$ and length of 2 cm, and studied characteristics of their photoluminescence.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.4 no.3
• /
• pp.18-29
• /
• 1993

In single mode fiber optic transmission systems(FOT's) operated at high modulation rates over long fiber spans, chromatic dispersion can produce distortion in the demodulated waveforms, resulting in intersymbol interference(ISI) in the received signal and a reduction of transmission system performance. In this paper, chromatic dispersion limitations for intensity modulation and direct detection(IM-DD) systems are studied by considering the effect of phase modulation to amplitude modulation (PM-AM) conversion noise. Laser phase noise conversion to amplitude noise due to fiber chromatic dispersion is analyzed by deriving the noise power spectral density. We first derive the noise power spectral density of the laser phase noise to intensity noise conver- sion. Next, also evaluate the system power penalty and the transmitter laser linewidth required to avoid PM-AM conversion noise penalties in long-haul nonregenerative transmission system using an external modulator and optical amplifiers. For such system with optical amplifiers, transmission sys- tem length is limited due to fiber chromatic dispersion, even if an ideal external modulator is used.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.44-48
• /
• 2002

In this paper, we demonstrated the simultaneous measurment of triple parameters such as strain, temperature, and vibration using single FBG/EFPI hybrid sensor. The FBG/EFPI sensor system for the strain and temperature measurement and the EFPI sensor system for the the vibration measurement were combined by a wavelength division multiplexer. The optical source of FBG/ EFPI sensor system is a wavelength-swept fiber laser(WSFL) and that of an EFPI sensor system is a laser diode. We performed the simultaneous measurement of thermal strain, temperature, and vibration of a aluminum beam placed in a thermal chamber and validated the efficiency of the constructed measurment system.

• Current Optics and Photonics
• /
• v.8 no.1
• /
• pp.65-71
• /
• 2024

We present a Yb-doped narrow-linewidth polarization-maintaining all-fiber amplifier that achieves a high mode-instability (MI) threshold, high output power, and 9.7-GHz spectral linewidth. Six wavelength-multiplexed laser diodes are used to pump this amplifier. First, we construct a high-power fiber amplifier based on a master oscillator-power amplifier configuration for experiments. Subsequently, we examine the MI threshold by individually pumping the amplifier with wavelengths of 976, 974, 981, 974, and 981 nm respectively. The experimental results demonstrate that the amplifier exhibits a high MI threshold (>3.5 kW) when pumped with a combination of wavelengths at 974 and 981 nm. Afterward, we inject an optimized phase-modulated seed with a nearly flat-top spectrum into this amplifier. Ultimately, laser output of 3.2 kW and 9.7 GHz are obtained.

• Korean Journal of Optics and Photonics
• /
• v.27 no.1
• /
• pp.1-17
• /
• 2016

Over the past two decades, fiber-based lasers have made remarkable progress, now having reached power levels exceeding kilowatts and drawing a huge amount of attention from academy and industry as a replacement technology for bulk lasers. In this paper we review the significant factors that have led to the progress of fiber lasers, such as gain-fiber regimes based on ytterbium-doped silica, optical pumping schemes through the combination of laser diodes and double-clad fiber geometries, and tandem schemes for minimizing quantum defects. Furthermore, we discuss various power-limitation issues that are expected to incur with respect to the ultimate power scaling of fiber lasers, such as efficiency degradation, thermal hazard, and system-instability growth in fiber lasers, and various relevant methods to alleviate the aforementioned issues. This discussion includes fiber nonlinear effects, fiber damage, and modal-instability issues, which become more significant as the power level is scaled up. In addition, we also review beam-combining techniques, which are currently receiving a lot of attention as an alternative solution to the power-scaling limitation of high-power fiber lasers. In particular, we focus more on the discussion of the schematics of a spectral beam-combining system and their individual requirements. Finally, we discuss prospects for the future development of fiber laser technologies, for them to leap forward from where they are now, and to continue to advance in terms of their power scalability.