• 센서학회지
• /
• 제22권3호
• /
• pp.227-232
• /
• 2013

In this research, fiber-optic pressure sensors were fabricated with rugate-structured porous silicon (RPS) diaphragms coated with PMMA (Polymethyl-Methacrylate). The reflectance spectrum of the PMMA/RPS diaphragm was almost the same as that of uncoated RPS diaphragm. However the mechanical strength of the PMMA/RPS diaphragm increased more than that of the uncoated diaphragm. As a result, the fiber-optic sensor fabricated with PMMA/RPS diaphragm could successfully detect more high pressure difference without diaphragm damage than the highest detectable pressure difference of the sensor with normal RPS diaphragm. The response data of the fiber-optic sensor recorded as a function of pressure difference were fitted by theoretical curves. During this process, elastic moduli of the used PMMA/RPS diaphragms were obtained numerically. The dynamic response properties of the fiber-optic sensor were also investigated under continuous variation of the pressure difference conditions.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.640-643
• /
• 1996

In this paper, a sensitivity of the fiber optic pressure sensor in water is demonstrated. A single mode optical fiber Mach-Zehnder interferometer used to detect the change in optical path length produced by the change of fiber optic strain in water. The sensitivity with this system measured 100.mu.psia through an experiment in the static response.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.478-481
• /
• 1995

This paper presents the system demonstrator for an optical fiber sensor system developed as a technological evaluator suitable for generic sensric sensing applications. The new type of fiber-optic sensor employed a diaphragm displacement transforms pressure into optical intensity. Form this sensing technique, we can know the variation of source intensity, the loss of a optical fiber, and the reflectivity of the diaphragm surface. Experimental results are applied to the low-pressure transducer suitable for measuring miniature pressure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.508-510
• /
• 1995

A fiber-optic pressure sensor is fabricated with a photoelastic glass material. To remove the influence of external pertubation along the optical fiber, a new referencing technique is proposed by using two light sources. LED with 870nm wavelength is used as light source for reference signal, and LED with 660nm wavelength is used as light source for modulation signal. The fiber-optic pressure sensor system shows good linearity within the pressure range of 0 to 5 $kg/cm^2$.

• 유공압시스템학회논문집
• /
• 제7권2호
• /
• pp.1-6
• /
• 2010

A new type fiber optic sensing system has been developed as a commercially available standard using the technique of hetero-core spliced fiber optic sensor, for the purposes of monitoring large scaled structures, preserving natural environments and measuring physical phenomenons. The sensing system has been tested and evaluated in a possible outdoor condition in view of the full scaled operation at actual sites to be monitored. Additionally, the developed system in this work conveniently provides us with various options of sensor modules intended to measure such physical quantities as displacement, distortion, pressure, binary states and liquid adhesion. The experiment study has been performed to examine the performance to a pseudo-cracking experiment in the outdoor situation, and to clarify temperature influences to the system in terms of the coupling of optical connectors and the OTDR stability. It has been verified that the sensing system is robust to the temperature change ranging from the general condition to the hard condition. Especially, in this study, the specification and performances of the pressure sensor have been demonstrated to show the capability of inspecting various physical quantities.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.876-879
• /
• 2004

The buried fiber optic cable as a distributed intrusion sensor for detecting and locating intruders along the long perimeters is proposed. Phase changes resulting from either the pressure of the intruder on the ground immediately above the buried fiber or from seismic disturbances in the vicinity are sensed by a phase-sensitive optical time-domain reflectometer. Light pulses from a Er:fiber cw laser with a narrow, <3kHz-range, spectral width and a frequency drift of < 1 MHz/min are injected into one end of the fiber, and the backscattered light from the fiber is monitored with a photodetector. Results of preliminary studies, measurement of phase changes produced by pressure and seismic disturbances in buried fiber optic cables and simulation of ${\varphi}-OTDR$ response over long fiber paths, to establish the feasibility of the concept are described. The field experiments indicate adequate phase changes, more than 1t-rad, are produced by intruders on foot and vehicle for burial depths in the 0.2 m to 1 m range in sand, clay and fine gravel soils. The simulations predict a range of 10 km with 35 m range resolution and 30 km with 90 m range resolution. This technology could in a cost-effective manner provide enhanced perimeter security.

• 비파괴검사학회지
• /
• 제26권4호
• /
• pp.255-259
• /
• 2006

광섬유 마하젠더 간섭계를 이용하여 넓은 범위에서 침입지를 상시 감지할 수 있는 센서시스템을 제작하였다. 충격에 의해서 생성되는 간섭신호의 변화를 푸리에 변환하고, 스펙트럼의 주파수와 피크 크기 변화를 관측하였다. 센서팔에 가해지는 충격의 속도변화에 따라 간섭계 출력의 주파수가 $4.25Hz\;s/m$ 증가하였고, 질량이 증가함에 따라 최대 주파수 성분의 크기가 $4.11{\times}10^2dB/kg$의 비율로 변화함을 알 수 있었다.

• 한국소음진동공학회논문집
• /
• 제22권7호
• /
• pp.626-633
• /
• 2012

In this paper, sound pressure sensitivity of the fiber optic acoustic sensor according to sensor direction and mandrel material were investigated experimentally. Three different directions were selected as stand, lay, and hole. Hollow cylinder type mandrel dimension is 30 mm in outer diameter, 45 mm in length, and 2 mm in thickness, and about 50 m optical fibers were wounded on the surface of the mandrel. Non-directional sound speaker was used as a sound source. Sagnac interferometer and single mode fiber, a laser with 1,550 nm in wavelength, $2{\times}2$ coupler were used. Based on the experimental results, lay direction's sensitivity is the highest in the frequency range of 2 kHz~4 kHz. 'PTFE+carbon' material is more sensitive than PTFE in the frequency range of 5 kHz~20 kHz. Sound pressure detection sensitivity depends on the mandrel direction and material under certain frequency.

• 센서학회지
• /
• 제6권3호
• /
• pp.172-179
• /
• 1997

간섭형 광섬유 센서의 경우 소자의 구성만 적절히 바꾸어 다른 종류의 측정에도 사용될 수 있다는 점에 착안하여 여러 종류의 센서를 동시에 신호처리할 수 있는 원격 다중화 광섬유 센서 시스템을 구현하였다. 구현된 센서 시스템의 신호처리는 간단한 광학 구성으로 원격 다중화 측정이 가능하도록 광섬유 Fabry-Perot 간섭형 센서배열을 가정하여 피측정량의 변화에 의한 간섭 무늬의 수만 카운트하는 디지털 신호처리로 구성되었다. 광섬유의 광학 효과에 대한 데이터를 종합함으로써 센서 시스템에 부착할 센서를 구현하기 위해 적합한 광학효과를 선택하는 기준을 제시하였으며, 한 예로서 반경 4.3 cm의 원형 다이아프램 중앙에 광섬유 Fabry-Perot 간섭계를 부착하여 광섬유의 스트레인 광학 효과를 이용하게 구성한 압력센서 1개를 센서 시스템에 연결하여 간섭형 광섬유 압력 센서 시스템을 구성하였다. 압력센서의 동작을 수조실험에서 확인함으로써 압력의 원격 측정이 가능함을 보였으며, 수조 실험의 길과 2 m의 측정범위에서 오차는 ${\pm}3.6\;cm$이내인 것으로 나타났다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.202-203
• /
• 2005

we present a pressure sensor based on the mechanically formed long-period fiber gratings. The attenuation properties of an output power as a function of an external pressure is able to apply to the in-line fiber pressure sensors for the vessels.