• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.386-393
• /
• 2018

Purpose: Chicken cutting is done manually, which is inefficient, unhygienic, and carries a high accident risk during processing. This study develops and evaluates an automatic chicken cutting machine that suits small-scale workplaces. Methods: This study developed an automatic chicken cutting machine equipped with four traverse blades and two longitudinal blades. An experiment was conducted with various blade rotating speeds and tray feed rates to evaluate the machine's performance. The chicken loss rate and chicken piece weights were measured to calculate the coefficient of variation (CV), thereby determining processing uniformity. Results: The optimal cutting conditions with the smallest chicken loss rate were 0.05 m/s tray feed speed and 18.8 m/s and 16.4 m/s for the traverse and longitudinal blades, respectively. The processing ran at 55.3 chickens per hour and the chicken pieces were more uniform when using the device than for hand-work processed pieces. Conclusions: The loss rate increased in proportion to the cutting-blade rotation speed due to the high cutting rate in meat. The loss rate also increased as the tray feed speed slowed because the cutting blade pushed the chicken meat. The tray feed speed should be increased to improve the amount processed per hour.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.2
• /
• pp.141-151
• /
• 2015

A new rock excavation method using an abrasive injection waterjet system has been developed to enhance the efficiency and reduce the vibration of tunnel excavation. The abrasive feed rate is an important factor for the cutting performance and the economical efficiency of waterjet-based excavation. In this study, various experiments were performed to explore the effects of major process parameters for both the abrasive feed rate and the suction pressure occurring inside the mixing chamber when the abrasives are inhaled. Experimental results reveal that the abrasive feed rate is affected by geometry parameters (abrasive pipe height, length, and tortuosity), abrasive parameters (abrasive particle size), and jet energy parameters (water pressure and water flow rate). In addition, the relation between the cutting performance and the abrasive feed rate was discussed on the basis of the results of an experimental study. The cutting performance can be maximized when the abrasive feed rate is controlled appropriately via careful management of major process parameters.

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.7
• /
• pp.991-994
• /
• 2000

Single cell of an indigenous phototrophic bacterium, Rhodovulum sulfidophilum, was incorporated in commercial fish feed for Oreochromis niloticus. The bacterial cell was analyzed for nutritional value and tested for toxicity and acceptability as an aquaculture feed supplement. The results showed higher survival rate and significantly higher growth rate (p<0.001) in O. niloticus fed with the bacteria incorporated fish feed. It is suggested that R sulfidophilum can be utilized as an aquaculture feed supplement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.74-79
• /
• 1996

The wear of partially coated pinion cutters under several cutting conditions was studied. In the realm of this experiment, chipping was a dominant tool wear mechanism and flank wear was much larger than crater wear. Under the condition of relatively low rotary feed and low radial feed rate, the wear due to chipping was concentrated at the nose part of pinion cutter. Increasing of rotary feed and radial feed rate alleviated the concentration of chipping at nose and prolonged tool life.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.36-41
• /
• 2012

In this study, we turning plastic mold steel (STAVAX) against cutting speed, depth of cut, feed rate using whisker reinforced ceramic tool (WA1). To predict cutting force, analyze principal, radial, feed force with multi-regression analysis. Results are follows: From the analysis of variance, affected factor to cutting force feed rate, depth of cut, cutting speed in order and cutting speed was very small affect to cutting force. From multi-regression analysis, we extracted regression equation and the coefficient of determination$(R^2)$ was 0.9, 0.88, 0.856 at principal, radial and feed force. It means regression equation is significant. From the experimental verification, it was confirmed that principal, radial and feed force was predictable by regression equation.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.47 no.5
• /
• pp.577-581
• /
• 2014

The aim of this study was to investigate the effect of diet extruder conditions, such as feed-loading rate and screw speed, on growth performance and biochemical responses in olive flounder Paralichthys olivaceus. Over 8 wks, we used four identical diets (triplicated per treatment) with differing ratios of feed-loading rate (kg/h):screw speed (rpm/min) in a laboratory-scaled twin-screw extruder of 50:640, 80:640, 120:640, and 80:400, designated as EP1, EP2, EP3, and EP4, respectively. Screw speed impacted the buoyancy of experimental diets. Diets produced at a screw speed of 640 rpm/min floated for > 24 hrs, whereas those produced at a speed of 400 rpm/min sank between 10 s and 5 min. Fish that were fed EP1 and EP4 diets grew significantly faster than those fed EP2 and EP3 diets. Fish fed EP1 diets ate and gained weight most efficiently among treatments, a result that is likely to be related to feed-loading rate, i.e., ingredients extruded at a low feed-loading rate may have more time to cook in the pre-conditioner of the extruder. A cooked diet may be easier to digest in fish. Fish fed EP4 diets also showed significant weight gain, as compared to those fed EP2 and EP3 diets. However, we found no differences among treatments in proximate compositions of dorsal muscle, liver, and viscera of fish. Our results suggest that extruder conditions, may influence feed quality, impacting feed efficiency and growth of fish.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.192-197
• /
• 2002

In this study, examined the cutting characteristics of alumuminum alloy AC8A-T6 that is used to present car piston materials. And in been holding materials machining empirically escape as result that experiment comparison changing the cutting speed and feed on various condition to choose efficient machining condition. The following results can be summarized from this research. 1. As the cutting speed decreased, principal cutting force and thrust cutting force is increased, and reason that cutting force interacts greatly in the low cutting speed is thought by result by BUE's stabilization. 2. The feed speed and cutting speed increase, friction factor is decrescent and the cause appeared the thrust cutting force is fallen than cutting force relatively because chip flow according to increase of the feed rate is constraint. 3. Though specific cutting resistance grows cutting area and the feed rate are few, the cause was expose that shear angle decreases by rake face of tool gets into negative angle remarkably as wear of a cutting tool or defect part of workpiece is cut. 4. Cutting speed do greatly depth of cut is slow, surface roughness examined closely through an experiment that becomes bad, and know that it can get good surface that process cutting speed because do feed rate by 0.1mm/rev low more than 250m/min to get good surface roughness can.

• Fisheries and Aquatic Sciences
• /
• v.26 no.10
• /
• pp.583-592
• /
• 2023

Celebes rainbow (Marosantherina ladigesi) is one of Indonesia's exported ornamental fish commodities, but the exploitation of this fish only relies on wild catches. The rise of unlimited fishing, especially those using poison, has changed the aquatic environment, threatening sustainability and causing fish extinction. This study aimed to evaluate the effectiveness of several types of feed in improving the absolute growth rate (AGR), specific growth rate (SGR), survival rate (SR), feed conversion ratio (FCR), feed efficiency (FE), hematology, and immune response of Celebes rainbow. The fish used in this study were male ornamental Celebes rainbow (M. ladigesi) weighing 1.32 ± 0.21 g/ind, reared in 54 L-aquariums at a stocking density of 30 individuals/aquarium for six weeks. The fish were fed according to the test diet consisting of live Tubifex sp worms, dry Tubifex sp worms, Spirulina platensis, and crumble pellets. The parameters observed were AGR, SGR, SR, FCR, FE, hematology, intestinal histology, liver histology, and a challenge test with the pathogenic bacteria Aeromonas hydrophila. The results showed that fish-fed live Tubifex sp worms had better AGR, SGR, SR, FCR, FE, hematology, and disease resistance compared to all other treatments. These results indicate that live Tubifex sp worms are the best feed for rearing Celebes rainbow.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.9
• /
• pp.1267-1271
• /
• 2001

The objective of this study was to examine the significance of feeding induced hypovolemia (decrease in plasma volume) in controlling the feed intake of goats fed on dry feed. In order to alleviate hypovolemia with feeding, a 2 h intravenous infusion (16-18 ml/min) of artificial saliva or mannitol solution was begun 1 h prior to feeding and continued until 1h after the start of the 2 h feeding period. In comparison with no infusion (NI), cumulative feed intake was increased by 41% with artificial saliva infusion (ASI) and by 45% with mannitol infusion (MI) by the completion of the 2 h feeding period. Both infusion treatments (ASI and MI) were significantly different (p<0.05) from the NI treatment in terms of the cumulative feed intake. The cumulative feed intake between the ASI and MI treatments was not significantly different (p>0.05). No infusion treatment (NI) had the lowest cumulative feed intake (929 g DM), whereas MI had the highest (1345 g DM), after completion of the 2 h feeding period. Generally, infusion treatments also increased the rate of eating at all time points after feeding was commenced. Following the first 30 mins of feeding, the rate of eating decreased sharply, and subsequently declined gradually in all treatments. Compared to the NI, both ASI and MI significantly (p<0.05) decreased thirst level (water intake for 30 mins after the completion of the 2 h feeding period) by approximately 13%. However, the thirst level caused by ASI and MI was not significantly different (p>0.05). Both ASI and MI decreased the plasma concentrations of osmolality and total protein, and hematocrit at 1 h after infusion. The results suggested that the thirst sensation in the brain could be produced by feeding induced hypovolemia. Moreover, the results indicate that hypovolemia is one of the factors controlling the feed intake of goats fed on dry feed.

• Journal of Powder Materials
• /
• v.10 no.5
• /
• pp.349-352
• /
• 2003

This study examined the correlation of various operational factors including reaction temperature and the quantity of reductant and diluent with the characteristics of powder using $K_2$ TaF$_{7}$ as feed materials, Na as a reductant and KCl/KF as a diluent. Also to control the particle size and shape, external supply system developed, it can provide a feed material and a reductant at a fixed quantity and evaluated the characteristics of tantalum powder. When the external supply system was applied instead of the batch type process that charges feed material, reductant and diluent at the same time, it was possible to induce regular reduction reaction between feed material and reductant, which increased the recovery rate and reduced the mixture of impurities. In particular, the application of the external supply system enabled the control of reaction temperature and reaction speed according to the feeding rate of feed material during reduced reaction, and resultantly it enabled the manufacturing of granular-shaped powder with a regular granularity of 2∼3 ${\mu}{\textrm}{m}$ and purity of 99.5%.