• 열처리공학회지
• /
• 제6권1호
• /
• pp.1-8
• /
• 1993

In this paper, the surface roughness influenced by Sm45C hardness in high frequency induction hardening and mechanical characteristics for the changed Hv 598 part and the unchanged hardness Hv 223 part by use of cermet and ceramic cutting tools was experimentally examined. Finally, we could be had some important results by processing surface roughness on cutting conditions such as cutting speed, feed rate, depth of cut and changes of tool nose radius. The results are summarized as follows. 1. In case of the same cutting condition, the hardness of workpiece was high and acquired the best processing surface roughness when the radius of the tool nose had 0.8 mm and feed rate was 0.04 mm/rev. 2. In case of the hardness of workpiece, though the cutting speed didn't have an effect on processing surface roughness, the less feed rate and the more processing surface roughness improved. On the other hand, the low inside the hardness of workpiece, the more cutting speed and the more feed rate increase, the processing surface of roughness improved. 3. Regardless of the hardness of workpiece, the change of the cutting depth didn't have great effect on the surface roughness. 4. On cutting the high surface hardness part with cutting tools of cermet and ceramic, it can be acquired the higher processing surface roughness because it hadn't been taken effect on cutting speed, In case of the cutting process of the low inside hardness part the two cutting tools have acquired the similar processing surface roughness.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.19-28
• /
• 2005

It is of great economic importance to minimize the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine. The motor-driven cylinder lubricator was first developed fur a large two-stroke marine diesel engine made in $W{\ddot{a}}rtsil{\ddot{a}}a$ Switzerland Ltd. by the joint research of industry-university. In this study, the effects of revolution speed, plunger stroke and cylinder back pressure on maximum discharge and delivery pressures, delivery delay duration, and oil feed rate are experimentally investigated by the home-manufactured cylinder lubricator. The maximum discharge pressure with a spot of 0.03 m and the maximum loss pressure at spots of 5, 6.78 and i 0 m away from the end of lubricator slot are increased as plunger stroke, revolution speed and back pressure are elevated, and the delivery delay duration is shortened as plunger stroke, revolution speed and oil pipe length are increased. Also, oil feed rate is increased as plunger stroke and revolution speed are raised, but lowered as the back pressure is increased.

• Journal of Biosystems Engineering
• /
• 제30권1호
• /
• pp.8-16
• /
• 2005

The extrusion-cooking condition on Cordyceps pruinosa was designed using twin-screw extruder. Response surface methodology (RSM) was used to investigate extrusion-cooking using a central composition design with varying die temperature $(114-146^{\circ}C)$, feed moisture $(22-38\%)$, feed rate (4-14 ka/h) and screw speed (120-280 rpm). System parameters (die pressure and specific mechanical energy (SME)) and extrudate parameters (density and water solubility index (WSI)) were statically analyzed using RSH. Die pressure was significantly affected by temperature, moisture contents and feed rate. SM was affected by screw speed and feed rate. When die temperature is $130^{\circ}C$ and moisture content $25\%$, the optimum pressure is shown. SME is about 20 Wh/kg, when feed rate is $10\~12kg/min$ and screw speed $200\~250rpm$. WSI was affected by temperature and moisture contents. Density was not affected by any factor. WSI increases by $7\%$ from about $23\%$ to about $30\%$, as temperature is raised from $120^{\circ}C\;to\;140^{\circ}C$. The WSI of Cordyceps pruinosa pulverized after extruding (PE) is about $26.97\%$ higher than that of raw material and $10\%$ higher than that of pulverized after drying (PD). The content of unsaturated fatty acid were not significantly different in PD and PE. Anti-oxidative activity of PE was 1.67-2.2 times higher than that of PD in Cordyceps pruinosa using 1- dipheny1-2-picrylhydrazyl method (DPPH).

• Journal of Biosystems Engineering
• /
• 제16권2호
• /
• pp.148-158
• /
• 1991

This study was undertaken to develop the feed rate control system for the head feed thresher by making use of the microprocessor and to evaluate the response of the system to a various threshing conditions. It was verified the performance of the control system through experiments. Control conditions were determined based on the simulation results of control system. The control system set at RH=500rpm, RL=480rpm for the bundle feed was considered optimum to give a high threshing capability and still to stabilize the feeding seed regardless of the bundle size. The control system for the continuous spread feed set at the range of LH=15mm, and LL=12mm gave a high control performance for the feeding mass of 1.1Kg/m and lower tested. In addition, the feed rate proportionality constant should be set lower than one in order to keep the rotational speed of threshing cylinder within the range of 500~520rpm.

• Journal of Biosystems Engineering
• /
• 제43권2호
• /
• pp.119-127
• /
• 2018

Purpose: Fermented feedstuffs have been found to improve productivity, reduce manure odor, and increase immunity. However, because there is not a commercialized pelletizing system for fermented total mixed ration (TMR) for pig feeding in Korea, a pelletizing system using TMR fermented feed was developed. Methods: The particle size, density, and volumetric density of the TMR feeds used in the test were measured. The pellet durability index (PDI, %) value of the pelletized TMR feed based on its moisture content, and the amount of pellet production based on the rotation speed of the compression roller were measured. Results: The test materials, TMR1 and TMR2, were approximately compressed to 387 kg/m3 with 18.2% (w.b.) and 544 kg/m3 with 22.2% (w.b.), respectively. Throughout this pellet molding test, the moisture content from 15 to 20% (w.b.) of mixture feedstuffs, including fermented forage, could be used for pellet molding. Based on the results, a small-scale pellet molding system of fermented TMR was designed and manufactured for pig farms. As rotation speed increased, the throughput increased, whereas the moisture content decreased by approximately 2% (w.b.) because of pellet molding. The best yield of pellets with 94.2% PDI was of 536 kg/h at 135 rpm rotation speed. Conclusions: Although the throughput of the prototype increased as the rotation speed increased, it was difficult to operate because of the greater noise and the lower PDI (%) at the higher rotation speed of the pellet molding rotor. It was found that the best production of pellets using the prototype was 536 kg/h having a PDI of 94.2% or more at a rotation speed of 135 rpm.

• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.896-905
• /
• 2003

A linear motor has many advantages next to conventional feed mechanisms: high transitional speed and acceleration, high control performance, and good positioning accuracy at high speed. Through the omission of a power transfer element, the linear motor shows no wear and no backlash, has a long lifetime, and is easy to assemble. A disadvantage of the linear motor is low efficiency and resultant high-temperature rise in itself and neighboring structures during operation. This paper presents the thermal behavior of the linear motor as a feed mechanism in machine tools. To improve the thermal behavior, an insulation layer is used. By placing the insulation layer between the primary part and the machine table, both the temperature difference and the temperature fluctuation in the machine table due to a varying motor load are reduced.

• 한국생산제조학회지
• /
• 제4권2호
• /
• pp.46-53
• /
• 1995

In this study, Wear of a ceramic cutting tool for hardened STD11 steel was investigated. Under the finish machining condition. DOC notch wear of a ceramic cutting tool was mostly occurred earlier than flank and crater wear were proceeded. The relations of DOC notch wear, which was characteristically produced at the beginning of cutting. to cutting speed, feed, depth of cut, and nose radius of a ceramic cutting tool were examined. Effective approach angle, which is a function of cutting conditions, and boundary area were suggested, and then the influence of those was investigated, The following conclusions were obtained: (1)as cutting speed was increasing. DOC notch wear was decreasing (2) the cutting condition that magnitude of slendermess ratio was made small, was favorable for DOC notch wear, (3) as depth of cut was smaller, the influence of feed on DOC notch wear was also smaller, (4) DOC notch wear was mainly influenced by effective approach angle, but by boundary area in the range of low feed.

• International Journal of Precision Engineering and Manufacturing
• /
• 제2권3호
• /
• pp.61-68
• /
• 2001

A linear motor has a lot of advantages in comparison with conventional feed mechanisms: high transitional speed, acceleration, high control performance and good positioning at high speed. Through the omission of a power transfer element, the linear motor shows no wear and no backlash, has along lifetime and is easy to assemble. Recently, the two types of linear motors, asynchronous and synchronous linear motors, are often applied to machine tools as a fast feed mechanism. In this paper, a comparison between the two types of linear motors as to power loss and thermal behavior is made. The heat sources of the linear motor-the electrical power loss in the motor and the frictional heat on the linear guidance-are measured and compared. Also, the temperature on the linear motor and machine structure is measured and presented.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.168-171
• /
• 2003

Generally RF AGC (Roll Force Automatic Gauge Control) controls the roll gap using the variation of rolling force caused by the roll eccentricity and the entry thickness of material, but RE AGC takes the bad effect of the roll eccentricity. The Feed-forward (FF) AGC method, which controls the next stand roll gap by the estimation of the thickness variation due to skid mark is needed to supplement the shortage of RF AGC. In this paper, an adaptive filtering method which takes account of the kind of material, the final objective thickness and the rolling speed is proposed to predict skid mark thickness variation. In addition, an improved estimation method of control point using a speedometer and looper angle is suggested. Via on line test, the performance improvement of the suggested FF AGC method is verified.

• 한국정밀공학회지
• /
• 제27권12호
• /
• pp.119-124
• /
• 2010

In this paper, thermal stabilization design of a new concept compact machining center has been investigated. A new concept machining center adopted a new X-axis as a NC rotary table. A New concept compact machining center is designed that spindle speed, feed rate and NC Rotary table speed are 12,000rpm, 60m/min and 110rpm each. The analysis is carried out by using FEM simulation Solidworks, CATIA and ANSYS. This paper is focused on the thermal deformation according to temperature distribution of a spindle system and feed drive system. Heat transfer analysis is performed according to heat source and atmosphere contact parts. As a result, this compact machining center is designed as a thermally stable structure.