• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.4
• /
• pp.83-90
• /
• 2014

The spiral up milling of an aluminum alloy was performed in this study. In accordance with the cutting condition, the surface roughness behavior and significance of the research with regard to specific factors were analyzed. The cutting speed, feed, and depth of the cut were found to be statistically significant. A higher cutting speed improved the surface roughness. On the other hand, as the feed and depth of the cut increase, the surface roughness decreases. An interaction effect between the feed and depth of the cut was detected. According to the surface roughness in relation to the cutting conditions, the model showed non-linear behavior.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.6
• /
• pp.373-380
• /
• 2018

This study proposes a new islanding detection method that uses the phase shift of feed-forward voltage and evaluates the performance of an existing method and the proposed method when the grid frequency changes within the allowable range under steady-state conditions. The investigated existing method, which is slip mode frequency shift (SMS), uses current phase shift to detect islanding. The SMS method supplies reactive current to the grid under this condition, but the proposed method does not generate additional reactive power because it does not depend on the current control loop. The performance in steady-state grid condition is evaluated through simulations and experiments.

• Journal of the Korean Wood Science and Technology
• /
• v.50 no.1
• /
• pp.59-67
• /
• 2022

Dietary fiber is considered a feed ingredient with high nutritional value in the broiler feed industry. Pine chips contain a large amount of dietary fiber and require some modification for use as broiler feed. In this study, pine chips were subjected to steam explosion under different severity factor (Ro) conditions to improve the chemical and physical properties of dietary fiber. The highest water-holding capacity, oil-holding capacity, and swelling capacity were found for Ro 4.0, followed by Ro4.5 and 3.5. The optimal condition for the steam explosion was determined to be Ro 4.0 (reaction temperature of 210℃, and reaction time of 6.0 min). Under these conditions, the water-holding capacity, oil-holding capacity, and swelling capacity of steam-exploded pine chips were 8.3 g/g, 6.5 g/g, and 5.0 mL/g, respectively. This study may contribute to the application of lignocellulose and related products in the broiler feed industry.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1043-1054
• /
• 1988

The optimum cutting condition of rake angle in turning was investigated in SM45C and SM20C. Results of experiments in SM45C and SM20C are as follow. Specific cutting resistance became higher as the depth of cutting, feed or cutting velocity decreases at same rake angle and resistance became low value at 20.deg.(SM45C), 10.deg.(SM20C). The optimum cutting condition for SM45C is depth of cutting 0.7mm, rake angle 30.deg., cutting velocity 200mm/min, feed 0.1mm/rev, and for SM20C is depth of cut 0.5mm, rake angle 10.deg., cutting velocity 150mm/min, feed 0.1mm/rev.The rake angle for good roughness is 15.deg for SM45C, and that for SM20C is 25.deg. The roughness is influenced by feed and it has the lowest value at 0.1mm/rev and the cutting condition is closely related with the change of cutting velocity and feed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.4
• /
• pp.142-148
• /
• 2008

This study aims to find the optimal cutting conditions, which are obtained by grinding condition, and the grinding characteristics and condition of constant velocity joint were investigated with respect to wheel velocity, depth of cut, feed speed. Grinding machine has been widely used in manufacturing optical reflects of metal. Such as steel are easy to be machined because of their proper material. As a result I obtained the data of grinding conditions makes good surface roughness and the optimal condition of grinding and get the mesh condition. The purpose of this study is to find the optimum grinding wheel characteristics for cutting constant velocity joint.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.85-96
• /
• 1988

The optimum cutting condition for rake angle in turning was investigated in (6-4) Brass and Al alloy. Results of experiments in (6-4) Brass and Al alloy are as follow. Specific cutting resistance becames higher as the depth of cutting, feed or cutting velocity decreases at same rake angle and resistance appear low value 20.deg., 25.deg.(6-4)brass, 0.deg. 20.deg.(Al alloy). The optimum cutting condition for(6-4) Brass is depth of cutting 0.5mm, rake angle 25.deg., cutting velocity 80m/min, feed 0.1mm/rev and for Al alloy is depth of cutting 0.1mm, rake angle 0.deg., cutting velocity 200m/min, feed 0.5mm/rev. The rake angle for good roughness is 20.deg. at (6-4) Brass, and that for Al alloy is 15.deg. The roughness is influenced by feed and it has the lowest value at 0.1mm/rev and the cutting condition is influenced by rake angle only.

• Korean Journal of Organic Agriculture
• /
• v.5 no.1
• /
• pp.125-135
• /
• 1996

A study was made to investigate the possibility of treating various organic waste of cattle manure, swine manure, goat manure, apple pomace, chinese medicine residue and coffee less by feeding these to earthworms and then by studying the growth and reproductive efficiency of earthworms, and the chemical composition of worm cast and its production. The results are summarized as follows. 1. When the feed for earthworms were in good condition which were cattle manure, swine manure and apple pomace, the reproductive efficiency of earthworms was improved however in worse condition the feed of which were goat manure and chinese medicine residue, the increasing rate(IR) became faster. 2. Despite the high content of organic matter(OM) in coffee lees, the earthworms fed coffee lees showed significantly lower reproductive efficiency and increasing rate(IR) than those fed other organic waste due mainly to its lower pH and lower total nitrogen(TN) content. Therefore, when coffee lees is considered to be fed to earthworms, it is believed necessary to be mixed with addiveves or other organic waste in order to improve the feed condition. 3. pH in swine manure, goat manure, apple pomace, chinese medicine residue and coffee lees became neutralized by being fed by earthworms. 4. Available P2O5 and exchangeable cation(EC) of earthworm cast were a little increased compared to those of feed. The contents of Mn, Fe and Cu in earthworm cast were a little decreased to compared to those of feed. 5. The contents of Mn, Fe and Cu in earthworm cast were a little a decreased to compared to those of feed. 6. Mean fresh weight of earthworm at final time(FW2) was negatively correlated with number of young worms(NY)(P<0.01), but positively with increasing rate(IR) (P<0.001) and C/N ratio(P<0.05) respectively. Number of cocoons (NC) and fresh weight of cocoons(WC) were positively(P<0.01) correlated with fresh weight of young worms (WY) and digested matter(DI) but negatively(P<0.001) correlated with residual matter(WY) and digested matter(DI) but negatively(P<0.001) correlated with residual matter(RW). Number of young worms(NY) and fresh weigh of young worms(WY) were negatively(P<0.001) correlated with increasing rate(IR), however increasing rate(IR) of earthworm was positively(P<0.05) correlatedd with C/N ratio.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.76-79
• /
• 1999

A study on simulation using Matlab shows the dynamic condition of a beam on feed-back with encorder. A controller for rapid response interpreted the stability on simulation with pole-placement technique. The effect of response was considered feed-back gain. The result of feed-back is described that various feed-back coefficient shows stable controll systems. It would be expected each result according to controllers.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.104-118
• /
• 1998

In this paper, the motion of ballscrew and shape of workpiece are the main objective variables varying with load conditions. To verify feed mechanism in NC lathe, the monitoring system is designed and cutting condition variables are spindle speed depth of cut and feed. During machining, rotation number of ballscrew motion of ballscrew in direction to gravity center and cutting force are measured. After machining, the roughness of workpiece is measured.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.563-564
• /
• 2006

In silicon wafer manufacturing process, the grinding process has been adopted to improve the flatness of water. The grinding of wafer is usually used by the infeed grinding machine. Grinding conditions are spindle speed, feed speed, rotation speed, grinding stone etc. But grinding condition selection and analysis is so difficult in grinding machine. In the intelligent grinding system based on knowledge many researchers have studied expert system, neural network, fuzzy etc. In this paper we deal grinding condition selection method, Taguchi method and Genetic Analysis.