• 한국공작기계학회논문집
• /
• 제14권2호
• /
• pp.21-26
• /
• 2005

From on the machining center cutting work of 5534, the characteristics such as spindle speed and feed speed fir the third point height, average spacing of roughness peaks, bearing ratio, center line average, ten point height. experiments is roughness for sampling length determine to measuring length of cutting feed speed 200, 400, 600, 800mm/min and spindle speed 800, 1000, 1200, 1400rpm. Third point height is spindle speed with most suitable cutting condition 1000rpm. Third point height is feed speed with most suitable cutting condition 400mm/min. Average spacing of roughness peaks are spindle speed with most suitable cutting condition feed speed increased to average spacing of roughness Peaks are increased. Spindle speed increased to average spacing of roughness peaks are decreased. Bearing ratio is spindle speed with feed speed increased to bearing ratio decreased. Center line average is spindle speed with most suitable cutting condition at 1200rpm feed speed with most suitable cutting condition at 200mm/min to cutting foe roughness suddenly decreased. Ten point height is spindle speed with most suitable cutting condition 1200rpm at ten point height cutting face roughness to decreased and feed speed with most suitable cutting condition 800mm/min at ten point height cutting face roughness to decreased.

• Korean Chemical Engineering Research
• /
• 제53권2호
• /
• pp.181-192
• /
• 2015

본 연구는 Liquid Crystal Display (LCD) 세척 후 발생하는 Propylene Glycol Monomethyl Ether Acetate (PGMEA)폐액 재활용을 위한 2기 증류탑을 사용하는 공정의 최적 조건을 산출하였다. 공정조건 최적화 기법으로 다중회귀분석을 이용하여 1차 증류 시 Bottom 온도(BTM 온도), Reflux 량, Feed 량 및 Feed 온도에 따라 PGMEA 함량에 대한 최적 조건과 2차 증류 시 BTM 온도, Reflux 량, Feed 량에 따른 PGMEA 함량에 대한 최적 조건과 공정인자를 산출하였다. 1차 증류탑의 공정인자 중 Reflux 량, Feed 온도 및 Feed 량이 중요한 인자로 산출되었다. 본 연구의 공정조건 범위에서는 BTM 온도범위가 PGMEA함량에 크게 영향을 주지 못하였다. 따라서 최적 공정 조건은 Feed 량 $5,700{\ell}$, Reflux 량 $2,500{\ell}$, BTM 온도 $165^{\circ}C$ 및 Feed 온도 $130^{\circ}C$이며 이때 예측된 PGMEA 함량은 92.12~94.62%로 산출되었다. 2차 증류탑에서는 Reflux 량이 함량에 많은 영향을 미치고 있으며, Feed 량과 BTM 온도도 영향을 미치는 인자로 산출되었다. 다중공선성(Multicollinearity)이 Reflux 량과 BTM 온도 간에 강한 양의 상관관계가 있어, 두 인자 중 다중회귀식에 영향이 지배적인 인자 하나를 선택하였으며, 최적조건은 BTM 온도 $199^{\circ}C$ 기준에서 최적 공정 조건은 Feed 량 $4,275{\ell}$ 및 Reflux 량 $6,200{\ell}$이며, 이때 예측 PGMEA 함량은 99.0~99.5%로 산출되었다.

• 한국정밀공학회지
• /
• 제23권12호
• /
• pp.38-45
• /
• 2006

In this work, optimal finish machining condition considering total time for mold or electrode manufacturing was investigated. First, manual finishing time according to the machining condition was analyzed for the work material. The effect of runout and phase shift of tool path on surface finish was also considered in those analyses. Secondly, optimal manual finishing processes were determined for various machining conditions. Finally, finish machining time and corresponding manual finishing time were taken into account for the estimation of the total time of manufacturing mold. Though small feed per tooth and pick feed reduced the manual finishing time, the finish machining time increased in such conditions. With a machining condition of feed per tooth of 0.2 mm and pick feed of 0.3 mm, the minimum total time of manufacturing mold was achieved in our machining condition.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.141-144
• /
• 2003

This paper proposes an analytical model of off-line feed rate scheduling to obtain an optimum feed rate for high speed machining. Off-line feed rate scheduling is presented as an advanced technology to regulate cutting forces through change of feed per tooth, which directly affects variation of uncut chip thickness. In this paper, the feed rate scheduling model was developed using a mechanistic cutting force model using cutting-condition-independent coefficients. First, it was verified that cutting force coefficients are not changed with respect to cutting speed. Thus, the feed rate scheduling model using the cutting-condition-independent coefficients can be applied to set the proper feed rates for high speed machining as well as normal machining. Experimental results show that the developed fred rate scheduling model makes it possible to maintain the cutting force at a desired level during high speed machining.

• Fisheries and Aquatic Sciences
• /
• 제24권9호
• /
• pp.311-317
• /
• 2021

Inclusion effect of various levels of jack mackerel meal (JMM) acting as feed attractants and/or stimulants in diets on the growth, feed consumption, feed utilization and whole body composition of rockfish was investigated. Three hundred juvenile rockfish were randomly allocated into 15 flow-through tanks. Five experimental diets supplemented with JMM at 0%, 1%, 3%, 5%, and 10% at the expense of anchovy meal were prepared and referred to as the JMM0, JMM1, JMM3, JMM5, and JMM10 diets, respectively. Weight gain, specific growth rate (SGR) and feed consumption of fish tended to improve with dietary levels of JMM. The greatest weight gain, SGR and feed consumption were observed in fish fed the JMM10 diet, followed by the JMM5, JMM3, JMM1, and JMM0 diets, in that order. Condition factor (CF) of fish tended to improve with dietary inclusion levels of JMM. Growth performance, feed consumption and CF of fish tended to improve with dietary inclusion levels of JMM ranging from 0% to 10%.

• 멤브레인
• /
• 제6권1호
• /
• pp.44-52
• /
• 1996

평판형 모듈 설계의 최적화를 목적으로 feed 흐름 조건에 따른 feed 온도 및 유속분포를 예측할 수 있는 모델식을 확립하였고 모델 모사를 통해 흐름 조건들이 온도 분포에 끼치는 영향들을 조사하였다. 모델내의 유체의 Re 크기가 커지면 채널 두께방향으로의 유속 구배가 커질 뿐 아니라 투과물 증발을 위한 에너지원인 feed 흐름 속도가 커져 물질 및 열흐름이 증가하여 투과물 증발로 인한 feed 온도 강하가 증어든다. 반면에 채널 간격이 작아지면 feed 흐름량이 상대적으로 작아져 급격한 온도 강하를 야기시킨다. Re 크기에 따른 feed 온도 변화는 실험결과와 일치함이 관찰되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.74-79
• /
• 1996

The wear of partially coated pinion cutters under several cutting conditions was studied. In the realm of this experiment, chipping was a dominant tool wear mechanism and flank wear was much larger than crater wear. Under the condition of relatively low rotary feed and low radial feed rate, the wear due to chipping was concentrated at the nose part of pinion cutter. Increasing of rotary feed and radial feed rate alleviated the concentration of chipping at nose and prolonged tool life.

• 월간피드저널
• /
• 제4권9호통권37호
• /
• pp.110-115
• /
• 2006

• 한국정밀공학회지
• /
• 제26권3호
• /
• pp.25-31
• /
• 2009

Femto-second laser ablation with the various feed velocities of the Invar alloy and the micro surface milling for the processing condition were studied. We used a regenerative amplified Ti:sapphire laser with a 1kHz repetition rate, 184fs pulse duration time and 785nm wavelength. Femto-second laser pulse was irradiated on the Invar alloy with the air blowing at the condition of various laser peak powers and feed velocities. An ablation characteristic according to feed velocity of the Invar alloy was appeared as the non-linear type at different zone of energy fluence. The micro surface milling of the Invar alloy using a mapping method was investigated. The optimal condition of micro surface milling was laser peak power of 22.8mW, feed velocity of 1 mm/s, beam gap of $1{\mu}m$. With the optimal processing condition, the fine rectangular shape without burr and thermal damage was achieved. Using the femto-second laser system, it demonstrates excellent tool for micro surface milling of the Invar alloy without heat effects and poor edge.

• Journal of Welding and Joining
• /
• 제24권5호
• /
• pp.67-73
• /
• 2006

Laser welding is suitable for welding to the aluminum alloy sheet. In order to apply the aluminum laser welding to production line, parameters should be optimized. In this study, the optimal welding condition was searched through the genetic algorithm in laser welding of AA5182 sheet with AA5356 filler wire. Second-order polynomial regression model to estimate the tensile strength model was developed using the laser power, welding speed and wire feed rate. Fitness function for showing the performance index was defined using the tensile strength, wire feed rate and welding speed which represent the weldability, product cost and productivity, respectively. The genetic algorithm searched the optimal welding condition that the wire feed rate was 2.7 m/min, the laser power was 4 kW and the welding speed was 7.95 m/min. At this welding condition, fitness function value was 137.1 and the estimated tensile strength was 282.2 $N/mm^2$.