• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 춘계학술대회 논문집
• /
• pp.652-659
• /
• 2000

The machine structure or parts has been arrive at a fracture, depend on crack by repeated load. Machine designer is estimate of fatigue strength in early stages the design for prevent fatigue fracture, then necessary its load history. This research study is using diesel locomotive in measurement of load history for fatigue design of rolling stock. The relation between velocity and amplitude of load history was found. We confirmed that the increase of velocity make to increase the magnitude of amplitude.

• 한국초전도ㆍ저온공학회논문지
• /
• 제3권1호
• /
• pp.1-5
• /
• 2001

In order to investigate the effect of fatigue damage on the properties of RRR in this study. fatigue tests at room temperature and residual resistivity measurement tests at 12K were carried out using annealed 9 strand Cu-Ni/NbTi/Cu composite cables Through fatigue tests of NbTi composite cables. a conventional S-N curve could be obtained even though there existed a possibility of fretting among strands, From the resistivity measurement of a NbTi strand after fatigue test, it was found that the RRR of xii·gin strand for annealed cables was 3 times more than that for as-received one. With increasing of fatigue cycles at a sress amplitude level. the RRR decreased. which was resulted from the accumulation of damage such as lattice defects and dislocation within the Cu stabilizer.

• 대한토목학회논문집
• /
• 제42권5호
• /
• pp.599-606
• /
• 2022

공용 중 강교량의 피로 평가에 활용할 수 있는 현장계측 데이터에는 대표적으로 변형률 계측과 Brigde Weight-In-motion (BWIM)이 있다. AASHTO The Manual For Bridge Evaluation에 따라, 대상 교량에서 계측된 데이터로부터 피로 상세에 가해지는 유효응력범위 및 반복응력 횟수를 추정할 수 있다. 추정된 유효응력범위와 반복응력 횟수를 통해 피로 손상 누적에 의한 신뢰도분석을 수행할 수 있다. 하지만 현장계측 데이터로부터 유효응력범위 및 응력범위 반복횟수를 추정하는 절차가 평가규정에 구체적으로 제시되어 있지 않고, 계측 데이터의 종류 또는 처리방법에 따른 피로 평가결과의 차이를 정량적으로 비교한 연구는 아직 미비한 실정이다. 본 연구에서는 공용 중 교량에서 동시에 계측한 변형률계 및 BWIM 데이터를 활용하여 피로 신뢰도평가를 수행하여, 활용되는 현장계측 데이터의 종류에 따른 평가결과의 차이에 대해 정량적으로 검토하였다. 이때, BWIM 데이터를 활용한 피로 신뢰도평가 시 구조해석모델의 정밀성이 평가결과에 미치는 영향을 검토하기 위해 평가 대상 교량의 뼈대요소 해석모델과 Shell-Solid 해석모델을 구축하였다. 또한, BWIM 데이터로부터 유효응력범위와 반복응력 횟수를 추정하기 위한 두 종류의 데이터 처리 방법을 정의하였으며, 이로 인한 피로 신뢰도 차이 역시 검토하였다.

• 국제학술발표논문집
• /
• The 9th International Conference on Construction Engineering and Project Management
• /
• pp.760-767
• /
• 2022

This paper introduces alert fatigue and presents methods to measure alert fatigue by using physiological signals. Alert fatigue is a phenomenon that which an individual is constantly exposed to frequent alarms and becomes desensitized to them. Blind spots are one leading cause of struck-by accidents, which is one most common causes of fatal accidents on construction sites. To reduce such accidents, construction equipment is equipped with an alarm system. However, the frequent alarm is inevitable due to the dynamic nature of construction sites and the situation can lead to alert fatigue. This paper introduces alert fatigue and proposes methods to use physiological signals such as electroencephalography, electrodermal activity, and event-related potential for the measurement of alert fatigue. Specifically, this paper presents how raw data from the physiological sensors measuring such signals can be processed to measure alert fatigue. By comparing the processed physiological data to behavioral data, validity of the measurement is tested. Using preliminary experimental results, this paper validates that physiological signals can be useful to measure alert fatigue. The findings of this study can contribute to investigating alert fatigue, which will lead to lowering the struck-by accidents caused by blind spots.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권5호
• /
• pp.482-490
• /
• 1997

The effects of strain amplitude. test temperature and stress on the fatigue properties for Ti-Ni wires were investigated using a rotary bending fatigue tester specially designed for wires. The fatigue test results were discussed in connection with the static tensile properties. The DSC measurement was conducted after fatigue test in order to clarify the change of transformation behavior due to the progress of fatigue. Under the temperature below or near the Af, the strain amplitude($\varepsilon_a$)-failure life (Nf) curve showed to be composed of three straight lines with two turning points. Of the 2 turning points, the upper one was coincident with the elastic limit strain and the lower one with the proportional limit strain. With rising of the test temperature above Af, the pattern of $\varepsilon_a$-Nf curve changed gradually to composition of 2 straight lines. The $\varepsilon_a$-Nf curve shifted depending on test temperature. In the short and medium life zones, the higher the temperature was, the shorter the fatigue life. However, in the long life zone, above the Af temperature, the fatigue life was not affected by the temperature. The transformation enthalpy measured after fatigue test was dependent on Nf, $\varepsilon_a$, and test temperature.

• 한국정보통신학회논문지
• /
• 제21권12호
• /
• pp.2357-2364
• /
• 2017

최근 건강관리에 대한 관심이 높아지면서 건강상태를 모니터링 하기 위한 스마트 웨어러블 디바이스가 활용되어 오고 있다. 본 논문에서는 스마트 웨어러블 디바이스와 연동된 피로도 측정 시스템을 개발하였다. 충분히 휴식을 취하면 회복되는 신체적인 피로도와는 달리 정신적인 피로도는 일의 능률이나 집중력을 떨어트릴 수 있으므로 측정을 통해 정신 건강 상태를 모니터링 할 수 있다. 본 시스템은 스마트 웨어러블 디바이스에서 계측한 데이터를 스마트폰으로 전송하고 정신적인 피로도를 계산해주는 기능을 제공한다. 피로도를 측정하기 위한 피로도 인덱스를 개발하여 1부터 5까지의 수치로 표현하였다. 또한 피로도 계산 결과와 설문조사 결과와 비교하여 독립표본 t-검정을 실시한 결과 통계적으로 유의한 값이 나왔다. 본 시스템은 사용자들이 건강을 효율적으로 관리하는 데에 활용될 것이다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.96-101
• /
• 2001

The development of a new experimental method is required to easily observe the growth behavior of fatigue cracks. To satisfy the requirement, an image processing technique was introduced to fatigue testing. The length of surface fatigue crack could be successfully measured by the image processing system. At first, the image data of cracks were stored into the computer while the cyclic loading was interrupted. After testing, crack length was determined using image processing software which was developed by ourselves. Block matching method was applied to the detection of surface fatigue cracks. By comparing the data measured by image processing system with the data measured by manual measurement with a microscope, the effectiveness of the image processing system was established. If the proposed method is used to monitor and observe the crack growth behavior automatically, the time and efforts for fatigue test could be dramatically reduced.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 추계학술대회 논문집
• /
• pp.263-268
• /
• 2001

The constant .DELTA. K fatigue tests are performed in SS41 and its weldment. The LASER ISDG method is used in determination of crack opening ratio. This method is more precise than indirect measurement method, faster and easier than other direct measurement method. And obtained results are followed 1) Crack opening ratio U is proportional to fatigue crack growth rate da/dN at constant .DELTA. K 2) Fatigue crack growth rate da/dN in weldment increases in weld metal and heat affected zone, decreases in base metal as crack grows.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 춘계학술대회 논문집
• /
• pp.164-169
• /
• 2000

The remote measurement system(RMS) as a new experimental method is limited in its application to crack measurements at elevated temperatures because of the oxide layer on the specimen surface. Since TiAlN and Cr coating layers have a high resistance to oxidation and wear, this paper proposed a TiAlN and Cr coating technique for specimens to facilitate the measurement of crack growth behavior using RMS. To investigate the effects of the coating layer, tension and fatigue tests were carried out at room temperature and at 538$^{\circ}C$, using specimens of 1Cr-1Mo-0.25V steel. From the experimental results, it was found that the mechanical properties of the TiAlN and Cr coated specimens were similar to those of the substrate. Accordingly, the TiAlN and Cr coated layer had hardly any influence on the fatigue crack propagation.

• 한국정밀공학회지
• /
• 제18권6호
• /
• pp.59-66
• /
• 2001

Fatigue strength of the welding structure is governed by the residual stress at the weldment toe and static tensile overloads were known as relieving the residual stresses. In this study, static tensile overloads were applied to the welding structures which caused the relief of residual stresses. The amount of residual stress relief was found as proportional to the change of fatigue limit at the given conditions. Based on the fact of the proportionality between the change of fatigue limit and that of residual stress, simple measurement technique is proposed. Modified stress-life curves base on proposed technique gave good agreement with test results.