• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.191-197
• /
• 1987

본 논문에서는 이상과 같이 그 중요성이 인정되는 작은 표면피로균열의 성장 특성을 조사하기 위하여 연강과 중탄소강에 두 종류의 작은 표면결함을 가공한 네가지 종류의 시험편을 제작하고, 응력비 R=-1인 소야식 회전굽힘 피로시험을 통하여 작은 표면결함이 피로강도에 미치는 영향과 그 성장특성을 조사한 후 응력확대계수 K를 사 용하는 방법과 반복전스트레인 확대계수범위 .DELTA. $K_{\epsilon}$t/를 비교 검토하여 그 유효성 을 조사하고 이를 파괴역학적 측면에서 고찰하였다.다.

• 비파괴검사학회지
• /
• 제23권3호
• /
• pp.246-253
• /
• 2003

항공기 구조를 모사하여 일련의 리벳 구멍을 갖는 AA2024-T3 박판 구조를 대상으로 피로하중에 의한 단균열(short crack)의 발생시점과 성장거동을 음향방출(AE)을 위주로 한 측정으로 평가하였다. AE 위치표정에 의해 단균열의 좌표를 정확하게 결정하였으며, 이동식 현미경으로 균열의 크기를 측정하였다. 누적 AE 발생수 곡선은 단균열의 발생과 성장에 따라 일정한 간격을 두고 급격히 증가하는 양상을 보임으로써 여러 차례의 계단식 곡선을 형성하였다. AE 위치표정에서는 리벳 구멍을 중심으로 파괴역학에 근거한 관심영역(ROI)을 설정하였으며, 웨이블릿변환 잡음제거 방법을 사용하여 위치표정의 정확도를 향상할 수 있었다. 실제로 탐지된 신호의 대부분이 단 균열의 발생 및 성장과 관계없는 외부 잡음신호로 나타났으며, ROI 내에서 발생한 AE 발생원의 위치도 구조의 기하학적 특징이나 신호대잡음비의 영향에 의해 왜곡될 수 있음을 알 수 있었다.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권2호
• /
• pp.132-137
• /
• 1996

Pb(Zr$_{x}$Ti$_{1-x}$ )O$_{3}$ solutions prepared by sol-gel processing with different Zr/Ti ratio were coated on Pt/SiO$_{2}$/Si substrates using spin coating method. Coated films were annealed by rapid thermal annealing at 650.deg. C for 20sec to fabricate Pb(Zr, Ti)O$_{3}$ ferroelectric thin films. Electrical properties of the films such as dielectric constant and loss, ferroelectric hysteresis, fatigue, switching time, and leakage current were measured. Hysteresis of the films with different Zr/Ti ratio yield Pr ranging 10-21.mu.C/cm$^{2}$, E$_{c}$ ranging 37.5-137.5kV/cm. Hysteresis curve was changed from square-type to slim type according to increasing Zr contents. Switching time was faster than 180ns, and leakage current was about 20.mu.A/cm$^{2}$. The film underwent above 10$^{8}$ cycles of reversed polarization showed fatigue with increased coercive field and decreased remnant polarization.tion.

• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.22-27
• /
• 1997

In general, the load which acts on the structure is almost independent of time in many locations. In this case. It is difficult to estimate the life with the service load history, because the structure is on the multi- axial and multi-point loading states. In this study, the service load of the excavator which is widely used in industry field was calculated using measured cylinder pressures and displacements. The fatigue life was estimated using the multi-axial and multi-point load counting method. Service load history of 4 pin joint which act independently each other is yielded by mult-axial and multi-point load counting method. The stress spectrum is yielded by superposition of the results of FEM stress analysis applied unit load. Palm- gren-Miner's cumulative Damage is 0.000804 for Von Mises equivalent stress sequence by one side fillet weld S-N curve. This result agress with Bench test results. As a result of this study, the fatigue life esti- mation using the multi-axial and multi-axial and multi-point load counting method is useful.

• 대한기계학회논문집A
• /
• 제21권10호
• /
• pp.1626-1635
• /
• 1997

It is important to ensure the reliability of the first localized reactor vessel steel. To satisfy with this purpose, a study on the impact/hardness, low cycle fatigue(LCF), crack growth rate(da/dN) and fracture toughness( ) of base material(BM) and weld metal(WM) were performed under room temperature air and corrosion conditions. A summary of the results is as folows : (1) Charpy impact absorbed energy of BM was the highest value, heat affected zoon(HAZ) and the lowest, WM. The hardness of BM was similar to HAZ. (2) Coefficients of Manson equation using the monotonic tensile test data were obtained for the present material. (3) The effects of stress ratio and ambient (120.deg. C and NaCl) condition on da/dN were investigated, da/dN with NaCl condition expressed the highest value. (4) The results of Charpy V-notch impact test had good correlation with $K_{IC}$ characteristics and the lowest curve of $K_{IC}$ for BM was derived, more researches about WM and HAZ are required hereafter.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.352-364
• /
• 2007

It is essential to reduce track maintenance costs and to extend the periodic replacements of continuous welded rails based on accumulated passing tonnage. As recently train load decrease and rail joints wear down less, the periodic replacements of continuous welded rails can be extended. There are many kinds of rail damage like squat, head-check and corrugation. These can be taken nondestructive or naked eye test. So the periodic replacements of continuous welded rails based on accumulated passing tonnage were examine with focusing on a crack of rail bottom of continuous welded rail. Therefore, this study measure dynamic response of track by metro train load, it compute impact coefficient and track spring coefficient for estimating a condition of actual track system. Also, it is converted the measured stress waveform into stress frequency histogram by the rain-flow counting methods, and then the equivalence of stress is calculated. As apply s-n curve of a new welded rail, accumulated fatigue damage ratio of laid rail and remaining service lives is estimated. This study suggest a plan of the periodic replacements of continuous welded rails based on accumulated passing tonnage classified by the types of track system.

• International Journal of Automotive Technology
• /
• 제2권1호
• /
• pp.9-16
• /
• 2001

The lifetime of power train components can be improved dramatically by finding crack initiation points with suitable software tools and optimization of the critical areas. With increasing capacities of computers the prediction of the lifetime for components by numerical methods gets more and more important. This paper discusses some applications of the outstanding fatigue simulation program FEMFAT supporting the assessment of uniaxially and multiaxially loaded components (as well as welding seams and spot joints). The theory applied in FEMFAT differs in some aspects from classical approaches like the nominal stress concept or the local one and can be characterized by the term "influence parameter method". The specimen S/N-curve is locally modified by different influence parameters as stress-gradient to take into account notch effects, mean-stress influence which is quantified by means of a Haigh-diagram, surface roughness and treatments, temperature, technological size, etc. It is possible to consider plastic deformations resulting in mean-stress rearrangements. The dynamic loading of power train components is very often multiaxial, e.g. the stress state at each time is not proportional to one single stress state. Hence, the directions of the principal axes vary with time. We will present the way how such complex load situations can be handled with FEMFAT by the examples of a crank case and a gear box.

• 대한기계학회논문집A
• /
• 제28권4호
• /
• pp.333-342
• /
• 2004

Tensile and low cycle fatigue (LCF) tests on prior cold worked 316L stainless steel were carried out at various temperatures from room temperature to 650$^{\circ}C$. At all test temperatures, cold worked material showed the tendency of higher strength and lower ductility compared with those of solution treated material. The embrittlement of material occurred in the temperature region from 300$^{\circ}C$ to 600$^{\circ}C$ due to dynamic strain aging. Following initial cyclic hardening for a few cycles, cycling softening was observed to dominate until failure occurred during LCF deformation, and the cyclic softening behavior strongly depended on temperature and strain amplitude. Non-Masing behavior was observed at all test temperatures and hysteresis energy curve method was employed to describe the stress-strain hysteresis loops at half$.$life. The prediction shows a good agreement with the experimental results.

• 한국산업융합학회 논문집
• /
• 제9권2호
• /
• pp.117-122
• /
• 2006

This paper is to provide some of the analysis procedures of the FAD(Failure Assessment Diagram), which is applied th the safety test of the atomic pressure vessels and other structures. Harrison proposed R-6 Diagram, and Bloom developed the method of DPFAD(Deformation Plasticty Failure Assessment Diagram). Analysis of J-integration of the plastic materials give the failure test curve for the materials with serious work hardening effect. J value was obtained form both FEM(Finite Element Mothod) and the experiment using compact type specimen for J=JIC, and the results were compared. In this study, the results of analysis using DPFAD and the factors affecting DPFAD in Static fatigue and fracture were reviewed. It was shown that the concept of DPFAD can be applied to test the safety of the structures.

• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.343-349
• /
• 2007

One of the useful technologies for light-weightening of components required in the automobile and machine industry is to use high strength materials. To improve material properties, the carbonizing treatment, nitrifying treatment, and shot-peening method are representatively applied. However, the shot-peening method is generally used to remove surface defect on steel and to improve the fatigue strength of the surface. Benefits of shot-peening are increasing resistance against fatigue, stress corrosion cracking, fretting, galling, erosion and closing of pores. In this paper, the effect of shot-peening on the corrosion of SUP-9 steel immersed in a 3.5% NaCl solution and corrosion characteristics from heat treatment during the shot peening process has been investigated. The immersion test was performed on four kinds of specimens. Corrosion potential, the polarization curve, residual stress etc. Were analyzed from the experimental results.