• 유공압시스템학회논문집
• /
• 제1권4호
• /
• pp.9-14
• /
• 2004

An estimation technique called the Extended Kalman filter is used to estimate viscous friction, spring initial contraction, and the spring constant on the swash plate of a variable displacement pump. The feasibility of the approach was established using a simulation study. It showed that these parameters could be estimated very accurately in a reliable and independent fashion. A special experimental system was set up to facilitate the measurement of certain states to enhance the Kalman Filtering approach. The aforementioned parameters were estimated and found to be reasonably repeatable for a common operating point. It was very evident that as the operating conditions changed (i.e. temperature) so did the estimated values of certain parameters such as viscous friction. This was believed to be a good verification test for the approach.

• 패션비즈니스
• /
• 제6권1호
• /
• pp.43-52
• /
• 2002

The purpose of this study was to present the plan for activation and rationalization of production of ladies' jacket and provide basic materials for improvement of the development of technologies in relation to the productivity improvement of ladies' jacket and the achievement of high quality product. For this purpose, this study attempted to investigate the present situation of jacket manufacturing process. The data is related with local ladies' jacket manufacturing companies in Seoul snd Kyonggi area. The results of this study are as follows. 1. 87.8% of the business firms responded that they acquired the productive process of jacket based on their own knowhow and 80.5% was aware of the need for the analysis of each process. The highest proportion of the business firms(65.9%) pointed out that the advantage of process analysis was the alleviation of the production time. 2. The jacket manufacturing process was made up of 4 stages such as the process of frontal/rear plate $\rightarrow$ the process of accessories $\rightarrow$ the process of completion $\rightarrow$ the process of finishing in a broad sense but composed of a total of 19 stages in detail. 3. Attachment of the sleeves(73.2), attachment of the collar(41.5%) and the formation of the overall silhouette(22.0%) were raised as the challenge in manufacturing ladies' jacket. 4. Most of the sewing business firms made use of the method of completing the collar and then stitching the outer material and the inner collar, and the line of the bodice and the outer collar as the method of stitching the tailored collar. and many of them used the method of completing the collar and then inserting it between the line of the bodice and the outer material and stitching it as the method of stitching the stand collar. They had a preference for the method of completing the sleeve and connecting it to the bodice as the method of stitching the sleeve. and used the method of treating the margin to seam of semi-lined and unlined jacket by treating it with the bias tape.

• 대한의용생체공학회:의공학회지
• /
• 제31권3호
• /
• pp.199-209
• /
• 2010

The locking compression plates-distal femur(LCP-DF) are being widely used for surgical management of the extra-articular complex fractures of the distal femur. They feature locking mechanism between the screws and the screw holes of the plate to provide stronger fixation force with less number of screws than conventional compression bone plate. However, their biomechanical efficacies are not fully understood, especially regarding the number of the screws inserted and their optimal configurations. In this study, we investigated effects of various screw configurations in the shaft and the condylar regions of the femur in relation to structural stability of LCP-DF system. For this purpose, a baseline 3-D finite element (FE) model of the femur was constructed from CT-scan images of a normal healthy male and was validated. The extra-articular complex fracture of the distal femur was made with a 4-cm defect. Surgical reduction with LCP-DF and bone screws were added laterally. To simulate various cases of post-op screw configurations, screws were inserted in the shaft (3~5 screws) and the condylar (4~6 screws) regions. Particular attention was paid at the shaft region where screws were inserted either in clustered or evenly-spaced fashion. Tied-contact conditions were assigned at the bone screws-plate whereas general contact condition was assumed at the interfaces between LCP-DF and bone screws. Axial compressive load of 1,610N(2.3 BW) was applied on the femoral head to reflect joint reaction force. An average of 5% increase in stiffness was found with increase in screw numbers (from 4 to 6) in the condylar region, as compared to negligible increase (less than 1%) at the shaft regardless of the number of screws inserted or its distribution, whether clustered or evenly-spaced. At the condylar region, screw insertion at the holes near the fracture interface and posterior locations contributed greater increase in stiffness (9~13%) than any other locations. Our results suggested that the screw insertion at the condylar region can be more effective than at the shaft during surgical treatment of fracture of the distal femur with LCP-DF. In addition, screw insertion at the holes close to the fracture interface should be accompanied to ensure better fracture healing.

• 한국의류산업학회지
• /
• 제20권2호
• /
• pp.219-225
• /
• 2018

The purpose of this study is to make an ideal dummy for adult Maltese with proper investigation of its character and direct measurement of dog body-shape. The results of the study are as follows; First, there were 6 factors to affect the characteristics of Maltese body in the analysis, which are size of body, leg shape, chest shape, leg thickness, body length, length between fore-legs. In the cluster analysis with the 6 factors there were two types of Maltese body. Type 1 has body characteristics with large body, thick leg, and small distance between front legs. Type 2 has average size of all factors including body size, leg thickness, and length between fore-legs. Second, type 2 was selected as a representative one to make a dummy reflected body shape of characteristics because it took 67.71% from entire considered factors and has average value in the measured size. The first dummy pattern was planned by copying the surface area of the representative body shape with the method of surgical tape. A dummy of single body with trunk and legs was made using 30's cotton cloth, polyester inside batting, compressed form PVC and metallic wire on the joint of trunk and legs to support dummy shape. The second pattern was made by correcting size difference of the pattern and adding the pattern of neck covering plate, metal magnetic button was inserted on the center of joint area of trunk and legs to make detachable legs for easy slip on and off the pet's wear.

• 한국의류산업학회지
• /
• 제19권5호
• /
• pp.579-588
• /
• 2017

This study investigates the wearing behavior and athleisure wear design preferences of women in their twenties as related to the design development of athleisure wear. A questionnaire survey was conducted on 185 women in their 20s. The survey was conducted from September to October 2016. Questionnaire items consisted of respondents' general items, athleisure wear and preference related items, and athleisure wear purchase related items. We collected 185 questionnaires from participants; subsequently, 169 were used as analytical data (except for incomplete questionnaires). The results of the study are as follows. Fit and wear comfort was the most important factor in the selection of athleisure wear. As a result of investigating the popularity of the athletic wear brand, the preference for the total sportswear brand was higher than the professional athletic wear brand. When the preferred colors were examined, the achromatic colors were ranked higher than chromatic colors. An examination of the preferred designs according to items indicated that the bra top preferred the 'U' shaped front plate and the 'Y' base basic type; in addition, T-shirts with the round neckline and the 1/4 length sleeves were preferred as tops. Leggings preferred long length type. It is necessary to develop a brand that matches the preference of the twenties' consumers by adjusting the aged target that can avoid the overheated competition and develop a niche market.

• 한국의류산업학회지
• /
• 제15권2호
• /
• pp.286-293
• /
• 2013

This study investigates the attachment of glycyrrhizin to fabric using an X-ray photoelectron spectrophotometer( XPS). XPS spectra analysis showed that carbon content on treated fabrics with 0.2% glycyrrhizin increased to 2.699% for silk, 2.829% for nylon, 1.505% for cotton, respectively. The results show that glycyrrhizin is absorbed on treated fabrics. The glycyrrhizin extraction method makes radix glycyrrhizae powder 10g treat the first and the second treatment with ethanol, remove impurities on $75^{\circ}C$; subsequently, it is treated for 10 hours with ethanol 75% on $85^{\circ}C$ and lyophilizated. As the result, glycyrrhizin is extracted 1.7g in GL-I, 1.1 g in GL-II. As the result of abstracting glycyrrhizin with two methods, pure glycyrrhizin was abstracted 45.9% in GL-I, 74.9% in GL-II. GL-I, GL-II; in addition, glycyrrhizin( Japan) on TLC plate was separated in Rf 0.6. By GL-II extract method, this experiment obtained glycyrrhizin 15 g treated in a bath ratio set to 1: 100. Silk fabric was treated at $80^{\circ}C$, 60 min. in, nylon fabric $10^{\circ}C$, 70 min., and cotton fabric $30^{\circ}C$, 80 min.; subsequently, silk, nylon, cotton fabrics showed a 99.9% antibacterial activity for Staphylococcus aureus and Klebsiella pneumoniae.

• 복식문화연구
• /
• 제28권3호
• /
• pp.299-312
• /
• 2020

The purpose of this study is to create a shirt sloper suitable for an elderly male body shape by producing virtual models using a 3D-virtualization program, making a torso prototype using the Yuka CAD system, and employing 3D simulation to virtualize and calibrate the model. First, the following three types of obese dummies are implemented through the CLO 3D program: Type 1 exhibits body fat in the lower body; Type 2 exhibits an obese abdomen; and Type 3 displays a balanced form of obesity. Second, for the design of the shirt pattern, the waist back length (measured value+1), back armhole depth (C/10+12+3+0.5~1.5), front armhole depth (back armhole depth 0~1), front interscye (2C/10-1+0.5-0.5), armscye depth (C/10+2+3.5+ 0.5), back interscye (2C/10-1+1), front chest C (C/4+2.5+1), back chest C (C/4+2.5-1), front hem C (C/4+2.5+1(+2)), back hem C (C/4+2.5-1(+2)), cap height (AH/3-5), and biceps width (Front AH-1, Back AH-1) are calculated. Third, the virtual attachment of the shirt pattern is resolved by increasing the front and back armhole depths, and the front and rear wrinkles are improved by adding a back armhole dart. The front hem lift and lateral pull caused by the protrusion of the abdomen are amended by increasing the margin of the chest, waist C, and hip C, with the appearance improved by balanced margin distribution in the front, back, and side panels. The improved retail pattern with an increase in the front armholes C was balanced on the torso plate.

• 한국의상디자인학회지
• /
• 제23권2호
• /
• pp.165-176
• /
• 2021

To solve environmental problems, research and efforts are required to reduce leather waste that is generated in large quantities during the leather manufacturing process. Leatherboard is a plate-like material that is made by crushing leather waste, such as trimming or shaving scraps and mixing fibers, pulp, rubber, and adhesives. The aim of this study is to provide basic data on the localization of leatherboard manufacturing technology for outsoles, which are increasingly in demand due to their excellent performance and price competitiveness. Interviews with experts and related organizations were conducted to investigate the related global technology trends. Also, the performance of three products that can be used as reference materials were evaluated and compared. As part of the research and efforts to reduce the amount of leather waste generated, high-performance materials using leather waste were developed and commercialized by major western companies. In Korea, various efforts have been made since 2000, and some companies have produced leatherboard for interior uses. However, the amount of waste recycled relative to that generated is not large due to the limited demand. Natural leather soles perform better than leatherboard soles in all evaluation aspects. In the case of leatherboard, performance varied by manufacturer. German products showed flexibility resistance and dimensional stability, thereby meeting performance requirements. However, abrasion resistance and cleavage resistance were slightly below the required performance standards, and research and development is needed to improve performance in those areas. Currently, it is impossible to evaluate the performance of domestic products due to underdevelopment. However, if the development of process technology continues based on the performance evaluation results of the best leatherboard in the shoe industry, materials for outsoles will be able to be produced domestically with prices competitiveness while realizing natural leather materials performance to some extent.

• 한국의류산업학회지
• /
• 제24권1호
• /
• pp.127-137
• /
• 2022

Recently, various clothing items are being developed using 3D printing technology, but comfort has become an issue while wearing them for a long time. Therefore, this study researched on how the temperature and humidity of the devices developed by 3D printing change depending on the material combination. Five types of material combinations (EVA foam, TPU density 10%, TPU density 30%, EVA foam+TPU density 10%, and EVA foam+TPU density 30%) were selected as variables, and the experiment was conducted for two different cases with and without a cover. All the ten types of samples were placed on the hot plate set at 36℃, and the surface temperature and humidity were measured at three different points for 10 minutes. As a result, the case with only TPU showed the greatest temperature change while the case with 100% EVA foam showed the least temperature change. The humidity of the surface layer gradually decreased with time for 100% EVA foam. For the case with TPU materials, the moisture was transferred to the surface layer at first, thereby increasing the humidity but then dropped significantly. Meanwhile, the cases with the cover on showed similar tendencies of change in both temperature and humidity where the overall temperature and humidity delivery were slow.

• 한국의류산업학회지
• /
• 제25권4호
• /
• pp.497-507
• /
• 2023

This study measured the effect 3D printing products comprised of different materials and shapes on heat transfer in clothing to derive fundamental data on thermal comfort among clothing comfort. The variables were three types of material (EVA foam, TPU-10%, TPU-10%+EVA), two types of shape (without holes, with holes), and two types of covers(without cover, with cover). All samples (12 types) prepared by combining these variables were placed on the hot plate set at 36℃, and the surface temperature was measured at three points for 10 minutes. The surface temperature change was dependent on the material, shape, and cover of the sample. The sample printed with TPU exhibited higher temperature transfer compared to the EVA foam sample after 10 mins. In addition, the temperature transfer was better when there were holes, and rate decreased when the sample was covered with fabric. We confirmed that material selection of the pad and thermal conductivity of the cover are extremely important in solving thermal stress to the human body caused by functional clothing with protectors. Additionally, as the protector, it is recommended to design the outer shell with a passage, such as a hole, to allow the rapid transfer of heat to the external environment.