• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1272-1280
• /
• 2014

This paper presents solutions for fault detection and diagnosis of two-level, three phase voltage-source inverter (VSI) topologies with IGBT devices. The proposed solutions combine redundant standby VSI structures and contactors (or relays) to improve the fault-tolerant capabilities of power electronics in applications with safety requirements. The suitable combination of these elements gives the inverter the ability to maintain energy processing in the occurrence of several failure modes, including short-circuit in IGBT devices, thus extending its reliability and availability. A survey of previously developed fault-tolerant VSI structures and several aspects of failure modes, detection and isolation mechanisms within VSI is first discussed. Hardware solutions for the protection of power semiconductors with fault detection and diagnosis mechanisms are then proposed to provide conditions to isolate and replace damaged power devices (or branches) in real time. Experimental results from a prototype are included to validate the proposed solutions.

• Journal of Korea Society of Industrial Information Systems
• /
• v.18 no.5
• /
• pp.45-50
• /
• 2013

Recently, as the market for SMART TV expands, the camera is embedded for providing various user experience. However, this leads to occurrence of camera failure due to TV power up sequence problem, which are usually not detectable in conventional test equipments. Although the failure-detection can be possible by re-generating control signals for audio interface with new equipment, it is expensive and also requires much time to test. In this paper, for SMART TV, FPGA(Field Programmable Gate Array)-based failure-detection system is proposed which can lead to reduction of both cost and time for test.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.175-177
• /
• 1995

The sensor signal validation and failure detection system must be able to detect, isolate, and identify sensor degradation as well as provide a reconstruction of the measurements. In this study, this is accomplished by combining the neural network, the Generalized Consistency Checking(GCC), and the Sequential Probability Ratio Test(SPRT) method in a decision estimator module. The GCC method is a computationally efficient system for redundant sensors, while the SPRT provides the ability to make decisions based on the degradation history of a sensor. The methodology is also extended to the detection of noise degradation. The acceptability of the proposed method is demonstration by using the simulation data in safety injection accident of nuclear power plants. The results show that the signal validation and sensor failure detection system is able to detect and isolate a bias failure and noise type failures under transient conditions. And also, the system is able to provide the validated signal by reconstructing the measurement signals in the failure conditions considered.

• Nuclear Engineering and Technology
• /
• v.17 no.2
• /
• pp.83-97
• /
• 1985

The Generalized Likelihood Ratio (GLR) method performs statistical tests on the innovations sequence of a Kalman-Buchy filter state estimator for system failure detection and its identification. However, the major drawback of the conventional GLR is to hypothesize particular failure type in each case. In this paper, a method to solve this drawback is proposed. The improved GLR method is applied to a PWR pressurizer and gives successful results in detection and identification of any failure. Furthermore, some benefit on the processing time lier each cycle of failure detection and its identification can be accompanied.

• ETRI Journal
• /
• v.41 no.4
• /
• pp.473-482
• /
• 2019

High availability and reliability have been considered promising requirements for the support of seamless network services such as real-time video streaming, gaming, and virtual and augmented reality. Increased availability can be achieved within a local area network with the use of the virtual router redundancy protocol that utilizes backup routers to provide a backup path in the case of a master router failure. However, the network may still lose a large number of packets during a failover owing to a late failure detections and lazy responses. To achieve an efficient failover, we propose the implementation of fast detection with virtual router redundancy protocol (FDVRRP) in which the backup router quickly detects a link failure and immediately serves as the master router. We implemented the FDVRRP using open neutralized network operating system (OpenN2OS), which is an open-source-based network operating system. Based on the failover performance test of OpenN2OS, we verified that the FDVRRP exhibits a very fast failure detection and a failover with low-overhead packets.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.27 no.3
• /
• pp.15-23
• /
• 2019

This paper contains analyses and development processes of the requirements to detect the possible intermittent failure in an old avionics backplane. Interconnections for signal transmission between electronic components, such as Pin-to-PCB, FPCB-to-FPCB, pin-to-FPCB, and pint-to-wire, were selected as the main cause of intermittent failure by analyzing target equipment and documents. The possibility of detecting intermittent failures occurring in the target equipment is verified by physics-of-failure analyses. In order to verify the occurrence of intermittent failures and their detectability, latching continuity circuit testers were manufactured and accelerated life tests were performed by applying temperature and vibration cycle in consideration of flight conditions. Through the above process, the detection requirements for the major intermittent failure in the target avionics backplane was developed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2609-2617
• /
• 2009

This paper describes the design overview of shared file system $SANique^{TM}$ and proposes the method for detection of failure node and recovery management algorithm. We also illustrate the characteristics and system architecture of shared file system based on SAN. In order to provide uninterrupted service, the detection and recovery methods are proposed under the all possible system failures and natural disasters. The various kinds of system failures and disasters are characterized and then the detection and recovery method are proposed in each disconnected computing node group.

• Structural Engineering and Mechanics
• /
• v.69 no.4
• /
• pp.407-416
• /
• 2019

This paper develops a wireless sensor for online fatigue crack detection and failure warning based on crack-induced nonlinear ultrasonic modulation. The wireless sensor consists of packaged piezoelectric (PZT) module, an excitation/sensing module, a data acquisition/processing module, a wireless communication module, and a power supply module. The packaged PZT and the excitation/sensing module generate ultrasonic waves on a structure and capture the response. Based on nonlinear ultrasonic modulation created by a crack, the data acquisition/processing module periodically performs fatigue crack diagnosis and provides failure warning if a component failure is imminent. The outcomes are transmitted to a base through the wireless communication module where two-levels duty cycling media access control (MAC) is implemented. The uniqueness of the paper lies in that 1) the proposed wireless sensor is developed specifically for online fatigue crack detection and failure warning, 2) failure warning as well as crack diagnosis are provided based on crack-induced nonlinear ultrasonic modulation, 3) event-driven operation of the sensor, considering rare extreme events such as earthquakes, is made possible with a power minimization strategy, and 4) the applicability of the wireless sensor to steel welded members is examined through field and laboratory tests. A fatigue crack on a steel welded specimen was successfully detected when the overall width of the crack was around $30{\mu}m$, and a failure warnings were provided when about 97.6% of the remaining useful fatigue lives were reached. Four wireless sensors were deployed on Yeongjong Grand Bridge in Souht Korea. The wireless sensor consumed 282.95 J for 3 weeks, and the processed results on the sensor were transmitted up to 20 m with over 90% success rate.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.1
• /
• pp.54-58
• /
• 2023

In this study, we compared the detection accuracy of the parameters of the scaffold failure detection model. A detection algorithm based on convolutional neural network was used to construct a failure detection model for scaffold. The parameter properties of the model were changed and the results were quantitatively verified. The detection accuracy of the model for each parameter was compared and the parameter with the highest accuracy was identified. We found that the activation function has a significant impact on the detection accuracy, which is 98% for softmax.

• Nuclear Engineering and Technology
• /
• v.33 no.5
• /
• pp.483-497
• /
• 2001

In this work, a neuro-fuzzy inference system combined with the wavelet denoising, PCA (principal component analysis) and SPRT (sequential probability ratio test) methods is developed to detect the relevant sensor failure using other sensor signals. The wavelet denoising technique is applied to remove noise components in input signals into the neuro-fuzzy system The PCA is used to reduce the dimension of an input space without losing a significant amount of information. The PCA makes easy the selection of the input signals into the neuro-fuzzy system. Also, a lower dimensional input space usually reduces the time necessary to train a neuro-fuzzy system. The parameters of the neuro-fuzzy inference system which estimates the relevant sensor signal are optimized by a genetic algorithm and a least-squares algorithm. The residuals between the estimated signals and the measured signals are used to detect whether the sensors are failed or not. The SPRT is used in this failure detection algorithm. The proposed sensor-monitoring algorithm was verified through applications to the pressurizer water level and the hot-leg flowrate sensors in pressurized water reactors.