• Journal of the Korean Wood Science and Technology
• /
• 제19권3호
• /
• pp.62-71
• /
• 1991

An evaluation of bending test of composite I and Box beams for determining the ultimate strength limit design criteria was presented. Maxium loads of composite I beams were found in beams composed of thicker upper flanges and/or vertical LVL flanges. These loads of plywood web beams were greater than those of PB web beams. Maximum loads of unsymmetrical box beams were less than those of symmetrical box beams. Thus, it took on different phase in box type beams. Ultimate loads of composite beams were greater than those of solid. The failure of composite beams were abrupt and failure mode was classified into following categories; Edgewise shear failure in web, delamination in flange-web joint, tension failure and tearing in LVL flanges, and web delamination. These failures of composite beams were appeared at the mixed mode. The influence factor affecting the performance of tested composite beams was shear strength of PB-web composite beams and compressive strength in plywood-web composite beams. It was also assumed that the influence factors on structural performance on composite beams were flange quality, web material and geometry of cross section. As one of the design methods resisting to compressive stress that was required in the case of small span to depth ratio and deep beams. composite I-beams composed of thicker upper flanges comparing to lower flanges were very effective in structural performance.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권3호
• /
• pp.245-251
• /
• 1999

이 연구는 탄소섬유판공법을 사용하여 보강된 철근콘크리트 슬래브에 집중하중 즉 같은 위치에서 휨모멘트와 전단력이 동시에 최대가 되는 경우에 대하여 탄소섬유판의 두께를 변수로 하여 슬래브의 구조적 거동을 실험하였다. 탄소섬유판의 두께에 따른 내력의 차이는 뚜렷이 나타나지 않았으며 이는 보강시험의 주된 파괴가 탄소섬유판의 파단이 아닌 하중점 주위에서의 휨-전단균열에서부터 층분리가 시작되기 때문이다. 그러므로 재하상태에 따른 설계방법을 다르게 할 필요가 있으며, 특히 같은 위치에서 휨 모멘트와 전단력이 최대가 되는 경우 탄소섬유판의 두께는 최대 0.6mm로 하고 무보강슬래브의 휨모멘트에 대한 보강된 슬래브의 휨모멘트는 1.5-2.0으로 제한하는 것이 바람직하다.

• 한국안전학회지
• /
• 제36권2호
• /
• pp.10-17
• /
• 2021

This paper presents the robust design of each component used in the development of an induction bolt heating system for dismantling the high-temperature high-pressure casing heating bolts of turbines in power plants. The induction bolt heating system comprises seven assemblies, namely AC breaker, AC filter, inverter, transformer, work coil, cable, and CT/PT. For each of these assemblies, the various failure modes are identified by the failure mode and effects analysis (FMEA) method, and the causes and effects of these failure modes are presented. In addition, the risk priority numbers are deduced for the individual parts. To ensure robust design, the insulated-gate bipolar transistor (IGBT), switched-mode power supply (SMPS), C/T (adjusting current), capacitor, and coupling are selected. The IGBT is changed to a field-effect transistor (FET) to enhance the voltage applied to the induction heating system, and a dual-safety device is added to the SMPS. For C/T (adjusting current), the turns ratio is adjusted to ensure an appropriate amount of induced current. The capacitor is replaced by a product with heat resistance and durability; further, coupling with a water-resistant structure is improved such that the connecting parts are not easily destroyed. The ground connection is chosen for management priority.

• Steel and Composite Structures
• /
• 제5권1호
• /
• pp.17-34
• /
• 2005

This paper presents an experimental study and its findings of the behavior of circular and square stub columns filled with high strength concrete ($f_c^{\prime}$=49MPa) and polymer cement concrete (PCC) under concentric compressive load. Twenty-four specimens were tested to investigate the effects of variations in the tube shape (circular, square), wall thickness, and concrete type on the axial strength of stub columns. The characteristics of CFT stub columns filled with two types of concrete were investigated in order to collect the basic design data for using the PCC for the CFT columns. The experimental investigations included consideration of the effects of the concrete fill on the failure mode, ultimate strength, initial stiffness and deformation capacity. One of the key findings of this study was that circular section members filled with PCC retain their structural resistance without reduction far beyond the ultimate capacity. The results presented in this paper will provide experimental data to aid in the development of design procedures for the use of advanced concretes in CFT columns. Additionally, these results give structural designers invaluable insight into the realistic behavior of CFT columns.

• Computers and Concrete
• /
• 제15권2호
• /
• pp.141-166
• /
• 2015

In the present study, a Finite Element Model has been developed and used to study the effect of diameter to wall thickness ratio (D/t) of steel tube filled with concrete under axial loading on its behavior and load carrying capacity. The model is verified by comparing its findings with available experimental results. Influence of thickness and area of steel tube on strength, ductility, confinement and failure mode shapes has been studied. Strength enhancement factors, load factor, confinement contribution, percentage of steel and ductility index are defined and introduced for the assessment. A parametric study by varying length and thickness of tube has been carried out. Diameter of tube kept constant and equals to 140 mm while thickness has been varied between 1 mm and 6 mm. Equations were developed to find out the ultimate load and confined concrete strength of concrete. Variation of lateral confining pressure along the length of concrete cylinder was obtained and found that it varies along the length. The increase in length of tubes has a minimal effect on strength of tube but it affects the failure mode shapes. The findings indicate that optimum use of materials can be achieved by deciding the thickness of steel tube. A better ductility index can be obtained with the use of higher thickness of tube.

• 콘크리트학회지
• /
• 제10권2호
• /
• pp.119-126
• /
• 1998

본 연구는 철근비와 보강판비를 조정한 보강철근비를 변수로 탄소섬유쉬트 접착된 철근콘크리트 보에 대하여 그 변형특성과 강도특성 및 파괴모드를 실험적으로 고찰한 것이다. 철근비와 보강판비가 증가할수록 최대내력은 증가하는 경향을 보이지만 탄소섬유쉬트의 겹수가 증가할수록 철근비 증가의 경우와는 달리 에너지흡수능력이 저하된다. 철근비와 보강판비에 따른 파괴모드를 구분하고 시험결과와 비교, 고찰하였던 바 파괴모드와 연성의 측면에서 보강철근비 е의 한계값을 0.87 max으로 제안하였다．탄소섬유쉬트와 철근콘크리트 보의 합성작용이 철근항복이후까지 유지되어 비선형적인 거동을 보임으로써 구조적거동이 양호하게 나타나는 것으로 입증되었다.

• Steel and Composite Structures
• /
• 제17권4호
• /
• pp.517-533
• /
• 2014

Experimental results of 39 specimens including concrete columns, RC columns, hollow steel tube columns, concrete filled steel tubular (CFT) columns, and reinforced concrete filled steel tubular (RCFT) columns are presented. Based on the experimental results, the load-carrying capacity, confined effect, ductility, and failure mode of test columns are investigated. The effects of the main factors such as width-thickness ratio (the ratio of external diameter and wall thickness for steel tubes), concrete strength, steel tube with or without rib, and arrangement of reinforcing bars on the mechanical characteristics of columns are discussed as well. The differences between CFT and RCFT are compared. As a result, it is thought that strength, rigidity and ductility of RCFT are improved; especially strength and ductility are improved after the peak of load-displacement curve.

• International Journal of Concrete Structures and Materials
• /
• 제11권1호
• /
• pp.1-16
• /
• 2017

The compression or tension-controlled failure mode of concrete beams prestressed with unbonded FRP tendons is governed by the relative amount of prestressing tendon to the balanced one. Explicit assessment to determine the balanced reinforcement ratio of a beam with unbonded tendons (${\rho}^U_{pfb}$) is difficult because it requires a priori knowledge of the deformed beam geometry in order to evaluate the unbonded tendon strain. In this study, a theoretical evaluation of ${\rho}^U_{pfb}$ is presented based on a concept of three equivalent rectangular curvature blocks for simply supported concrete beams internally prestressed with unbonded carbon-fiber-reinforced polymer (CFRP) tendons. The equivalent curvature blocks were iteratively refined to closely simulate beam rotations at the supports, mid-span beam deflection, and member-dependent strain of the unbonded tendon at the ultimate state. The model was verified by comparing its predictions with the test results. Parametric studies were performed to examine the effects of various parameters on ${\rho}^U_{pfb}$.

• Archives of Metallurgy and Materials
• /
• 제65권3호
• /
• pp.1069-1072
• /
• 2020

Mortar feedstock is extruded to form bead and it is selectively placed line by line in the material extrusion additive manufacturing. With respects to part building process healthiness, load-supporting ability of overlaid beads is emphasized as buildability. Buildability is primarily dependent on thixotropic properties of feedstock and vertical overlapping schedule. In the present study, water-to-binder (w/b) ratio was chosen as material aspect to assess buildability. Uneven bead shape evolution and premature failure were highlighted owing to low yield stress of high w/b ratio feedstock. Feedstock with optimum w/b ratio showed good buildability even at the interval time of 19 sec.

• 한국구조물진단유지관리공학회 논문집
• /
• 제18권2호
• /
• pp.21-29
• /
• 2014

본 연구에서는 GFRP 이형 보강근으로 휨보강된 보의 거동, 파괴유형과 강도를 평가하였다. 4개의 보 실험체들을 제작하여 실험을 수행하였다. 4점 하중재하 조건으로 단순지지된 GFRP로 보강 콘크리트 실험체의 거동과 하중-처짐을 관찰하였다. 전단배근으로 인한 거동의 불확실성을 배제하기 위하여 스터럽을 배근하지 않고 실험체를 제작하였다. 실험 변수는 전단지간비와 유효보강비이다. 실험체의 길이는 3,300 또는 $1,950mm{\times}200mm{\times}240mm$이고 순지간 2,900 또는 1,000mm이다. 전단지간비는 6.5와 2.5이며, GFRP 유효 보강근비는 $1.126{\rho}_{fb}$, $2.250{\rho}_{fb}$, $3.375{\rho}_{fb}$와 $0.634{\rho}_{fb}$이다. 실험 결과 모든 실험체는 전단파괴 되었으며 실험계획에 적용한 ACI 440.1R, CSA S806와 ISIS의 전단 강도식이 실제와 편차가 있음을 확인하였다.