• 전기학회논문지
• /
• 제57권3호
• /
• pp.429-432
• /
• 2008

Much studies have been concentrated to develop the fabrication technique for high critical current density but still there are a lot of gap which should be overcome for large scale application of superconducting materials at liquid nitrogen temperature. The improvement of the critical current can be achieved by forming the nano size defect working as a flux pinning center inside the superconductor. In this paper, the establishment of fabrication condition and additive effects of second elements were examined so as to improve the related properties to the practical use of superconductor.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1466-1469
• /
• 2004

Micro spherical lens mold processing method based on mechanical one completes a spherical shape by setting a diamond tool of hundreds $\mu$m radius on spins with high speed and then using Z-axis vertical feeding motion like the fabrication of micro drilling. In this method, we can see unprocessed parts shaped like cylinder and cone and check increasing chatter marks and burrs by setting errors of the central axis of rotation on the edge of the tool. That is why this method doesn't suit for the optical lens mold. In this paper presents unprocessed parts are disappeared and chatter marks and burrs are decreased from centre of the lens after using Run-out measuring and setting system on run-out occurred from setting tool. Also the fabrication characteristics of 6：4 Brass, A1601, PMMA are compared and analyzed, establishing the optimum machining condition on each material.

• 한국전기전자재료학회논문지
• /
• 제21권1호
• /
• pp.57-62
• /
• 2008

From the progressing results, it was found that thin film using 52 wt% Ni - 38 wt% Cr - 3 wt% Al - 4 wt% Mn - 3 wt% Si target has good characteristics for low TCR (temperature coefficients of resistance) and high resistivity. The optimum sputtering condition was DC 250 W, 5 mtorr, and 50 sccm and the proper annealing condition was $350^{\circ}C$/3.5 hr in air atmosphere. At these fabricated conditions, thin film resistors with TCR values of less than ${\pm}10ppm/^{\circ}C$ were obtained. The TCR of the packaged-samples made at proper fabrication conditions was $-3{\sim}15ppm/^{\circ}C$ after the thermal cycling and $-20{\sim}180ppm/^{\circ}C$ after PCT (pressure cooker test), we could confirm reliability for the thin film resistor and find the need for enduring research about packaging method.

• 한국표면공학회지
• /
• 제29권1호
• /
• pp.60-72
• /
• 1996

A photoetching process is widely used for small and high precision parts in machinery, electronic and semi-conductor industries. One of the high precision parts, grid is very important part of digitron which use electron display, and it is fabricated by only photoetching process because of high precision. In this study, to develop high precision digitron grid, characteristics of etching solution were investigated with electrochemical test, that was potentiodynamic test and immersion test in the ferric chloride solution and added some additives. Based on the electrochemical etching test, grid was fabricated by continuous photoetching process at various etching condition. From the result of measured line width and etching depth under-cut and etching factor were calculated. For the fabrication of 25$\mu\textrm{m}$ line width, optimal etching condition was etching temperature 40~$45^{\circ}C$, spray pressure 1.5kg/$\textrm{cm}^2$ and etching time 3~4min.

• 한국광학회지
• /
• 제11권4호
• /
• pp.255-260
• /
• 2000

유기 금속화합물을 출발물질로 이용하는 졸-겔 방법으로 균열이 없는 유기-무기 복합 실리카 박막을 제작하였으며, 코팅방법, 조성비, prebake, postbake 온도 등의 제작조건에 따른 박막의 두께 및 굴절률의 변화를 체계적으로 조사하여 재현성 있는 제작조건을 확립하였다. 특히 광개시제를 첨가하였을 때 자외선 노광량에 따른 광학적 성질변화를 세 가지 광개시제에 대하여 측정, 비교하였다. 또한 졸-겔 박막으로 다중모드 간섭을 이용한 광 파워 분배기를 제작하여 광소자로의 응용 가능성을 살펴보았다.

• 한국세라믹학회지
• /
• 제44권10호
• /
• pp.548-553
• /
• 2007

Ceramic green sheets consisting Bi-based glass frit were fabricated for an application to PDP transparent dielectric front panel. The dispersion condition of the slurry for tape casting was pre-examined, and two kinds of hinder and plasticizer were used in the non-aqueous slurry system. In the fabrication process for the frit film, the properties such as dry and firing shrinkage, elongation, and transmittance were examined at the condition of various mixing ratio of plasticizers. In the mixing ratio of polyethylene glycol to dibutyl phthalate of 3:5wt%, a good adhesion, elongation and transmittance were observed at the firing temperature of $580^{\circ}C$. The photograph for the cross section of the interface was also showed a dense microstructure.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.382-385
• /
• 2001

In the previous study, a new LTCC material in the $PbWO_{4}-TiO_{2}-B_{2}O_{3}-CuO$ system was introduced. The developed material can be sintered at $850^{\circ}C$ and its dielectric properties are $\varepsilon_{r}=20-25$, $Q{\times}f_{o}=30000\sim50000GHz$, and $\tau_{f}=0.2{\sim}30ppm/^{\circ}C$, respectively. Therefore this material can be used as a LTCC substrate material for fabrication of multilayered high frequency communication module set. In present study, using this material, tape casting condition was established. With this condition, a multilayered resonator was fabricated and its electrical properties were examined. In present study, an antenna-duplexer module was also fabricated. Frequency characteristics of as-fabricated antenna-duplexer module was compared with simulation results.

• 패션비즈니스
• /
• 제15권4호
• /
• pp.110-121
• /
• 2011

As car seat is the closest part between driver and rider, the interest of the security and comfort of the seat is increasing. This research discovered the best condition for dyeing and finishing to produce a fabric for car seat and also developed the design of fabrication to give the feeling from such a finishing. The best condition of coating finishing solution is aqueous PU 65%, dye resist reagent 20%, water 12%, thicker 3%, and knife thickness 2mm, tenter temperature $170^{\circ}C$, tenter speed 35yard/min, viscosity 12,000cps and stirring time 100kg * 30min. According to the processing time of knife coating upon stirring the change of resin and the uneven of coating quantity was shown. This problems will be solved by means of automatic temperature control apparatus for resin and sealing device through a coming research.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 춘계 기술심포지움 논문집
• /
• pp.134-137
• /
• 2002

A new LTCC material in the $PbWO_4-TiO_2-B_2O_3-CuO$ system was developed. The developed material can be sintered at $850^{\circ}C$ and its dielectric properties are $\varepsilon_r=20-25, Q\timesf_o=30000~50000GHz$ , and $\tau_f=0.2~30ppm/^{\circ}C$, depending on the components moi ratio. Due to its low sintering temperature and microwave dielectric properties, the developed material can be used as a LTCC substrate for fabrication of multilayered microwave communication module set. In present study, using this material, tape casting condition was established. With this processing condition, a T-resonator was fabricated and its electrical properties were examined. Also, a 2-Pole band pass filter was fabricated and its frequency characteristics were compared with simulation results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.382-385
• /
• 2001

In the previous study, a new LTCC material in the PbWO$_4$-TiO$_2$-B$_2$O$_3$-CuO system was introduced. The developed material can be sintered at 850$^{\circ}C$ and its dielectric properties are $\varepsilon$$\sub$r/=20-25, Qxf$\sub$o/=30000∼500000Hz, and $\tau$$\sub$f/=0.2∼30ppm/$^{\circ}C$, respectively Therefore this material can be used as a LTCC substrate material for fabrication of multilayered high frequency communication module set. In present study, using this material, tape casting condition was established. With this condition, a multilayered resonator was fabricated and its electrical properties were examined. In present study, an antenna-duplexer module was also fabricated. Frequency characteristics of as-fabricated antenna-duplexer module was compared with simulation results.