• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.131-137
• /
• 2003

We have performed computer simulation to obtain electro-optic chracteristics of reflective liquid crystal display (LCD) using wide viewing angle LC mode, fringe field switching(FFS). Unlike other reflective LCD modes, in the FFS mode, the LC director in plance so an application to reflective display consisted of polarizer, LC layer and reflector is possible. when an incident light is 550mm, the optimal cell retardation value is 0.1365${\mu}$m and the efficiency of reflectivity is high over 90% with very little wavelength dispersion. Further, we have studied a new reflective display with polarizer, optical compensation film with half plate, LC plus reflector. The display with optimized cell parameters shows high contrast ratio (CR) over 130 with high light efficiency over 90% at normal direction and the CR greater than 5 exists over 60$^{\circ}$ of polar angle in all directions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1100-1106
• /
• 2004

In this paper, we intend to make fringe-field switching (FFS) mode cell by the ion beam (IB) alignment method on the a-C：H thin film, to analyze electro-optical characteristics in this cell. We studied on the suitable inorganic thin film for fringe-field switching (FFS) cell and the aligning capabilities of nematic liquid crystal (NLC) using the alignment material of a-C：H thin film as working gas at 30 W rf bias condition. A high pretilt angle of about 5 $^{\circ}C$ by ion beam (IB) exposure on the a-C：H thin film surface was measured. Consequently, the high pretilt angle and the good thermal stability of LC alignment by the IB alignment method on the a-C：H thin film surface as working gas at 30 W rf bias condition can be achieved. An excellent voltage-transmittance (V -T) and response time curve of the IE-aligned FFS-LCD was observed with oblique IB exposure on the a-C：H thin films. Also, AC V-T hysteresis characteristics of the IB-aligned FFS-LCD with IE exposure on the a-C：H thin films is almost the same as that of the rubbing-aligned FFS cell on a polyimide (PI) surface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.2
• /
• pp.185-188
• /
• 2006

We studied on the reverse twist near the pixel edge depending on the rubbing direction for the fringe field switching (FFS) mode. Liquid crystal (LC) dynamic and the transmittance near the pixel edge, where the various field directions are generated, depend on the initial rubbing direction because the position of reverse twist is decided by the angle between the electric direction and the LC director at a bias voltage. For example, when the rubbing angle is $7^{\circ}$, the reverse twist appears on the bottom position of the right sharp comer of the pixel edge so that the reverse region exists far away from main active region. But, when the rubbing angle is $-7^{\circ}$, the reverse twist appears on the top position of the right sharp comer of the pixel edge, resulting that the region becomes more close to the main active area and the unstable disclination lines (DLs) easily intrude into the active region. Therefore, it is necessary to keep the reverse twist region far from the active region and it is possible by controlling the rubbing direction in the design of a pixel electrode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.469-470
• /
• 2008

We have studied electro-optic characteristics as a function of splay elastic constants ($K_{11}$) in the fringe-field switching (FFS) mode using the LC with positive dielectric anisotropy. When $K_{11}$ is increased from 7.7pN to 11.7pN, a maximum transmittance is slightly increased and rising time become a little bit fast. However, operating voltage and threshold voltage is independent. In opposition to rising time, decay time is not affected by $K_{11}$. We already know that $K_{11}$ affects tilt angle of liquid crystals. Therefore, on the occasion of high $K_{11}$, liquid crystals are mainly affected by twist deformation because the higher $K_{11}$, the less tilt angle. In the FFS device, high $K_{11}$ is favorable to reduce tilt angle in on state and thus improve rising response time.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1132-1136
• /
• 2004

In this paper, we intend to make FFS mode cell with LC alignment used non-rubbing method, ion beam alignment method on the a-C:H thin film, to analyze electro-optical characteristics in this cell. We studied on the suitable inorganic thin film for FFS-LCD and the aligning capabilities of nematic liquid crystal (NLC) using the new alignment material of a-C:H thin film as working gas at rf bias condition. A high pretilt angle of about 5$^{\circ}$ by ion beam(IB) exposure on the a-C:H thin film surface was measured. An excellent voltage-transmittance (V-T) and response time curve of the ion-beam-aligned FFS-LCD was observed with oblique ion beam exposure on the DLC thin films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.163-163
• /
• 2009

Viewing angle controllable liquid crystal display (LCD) associated with fringe-field switching (FFS) mode with high image quality is proposed. In the device, one pixel is composed of main and sub pixels, in which adjacent sub pixel is patterned with pixel electrodes direction orthogonal to the adjacent one. In this way, light leakage can be generated in the all viewing angle directions except the normal direction, realizing view angle controllable LCD in both horizontal and vertical directions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1266-1269
• /
• 2004

This study focuses on the color characteristics of FFS (Fringe Field Switching). We use various methods to prove the high performance of color characteristics in the Fringe Field Switching mode. We have described a color performance of 15" XGA product by the viewing angle range using x, y parameters of CIE chromaticity diagram. And so we used the 2 dimensional analyzing to prove the color shift distribution by viewing angle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.311-318
• /
• 2004

We have studied electro-optic characteristics as a function of pretilt angle ($\theta$$_{p}$) in the fringe-field switching (FFS) mode using the LC with positive dielectric anisotropy. When $\theta$$_{p}$ is increased from 0$^{\circ}$ to 20$^{\circ}$, a maximum transmittance and an operating voltage are obviously decreased. In the viewing angle characteristics, the cell with low pretilt angle has a wide region for the contrast ratio greater than 5 and has a best luminance uniformity. Therefore, in the FFS device, a low pretilt angle is favored for high transmittance and wide viewing angle.gle.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.780-783
• /
• 2006

In this paper, we confirmed the yellowish gravity-mura phenomenon in Fringe-Field Switching (FFS) mode using 2-D simulation. As the cell gap increases, while the LC efficiency of blue wavelength remains almost same, that of red and green wavelength increases continuously. As a result, yellowish phenomenon occurs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.349-352
• /
• 2005

In this paper, we have investigated the hydrogen effects on Diamond-like Carbon (DLC) as an LC alignment layer of the FFS mode. By change of a Hydrogen content in the DLC sputtering process, the image sticking and electro-optic characteristics of Black-White panel with DLC / IB technology were examined.