• Structural Engineering and Mechanics
• /
• v.49 no.1
• /
• pp.23-40
• /
• 2014

In this article, using finite element method of analysis (FEM), behavior of the endplate moment connection subjected to axial force and bending moment is investigated. In the FEM model, all the nonlinear characteristics such as material, geometry, as well as contact have been included. First, in order to verify the numerical model of the connection, an analysis of the endplate moment connection conducted without the application of the axial force. Results obtained from FEM indicating a close and good correlation with the experimental results. Then to investigate the influence of the axial forces, the connections subjected to axial forces as well as the bending moment are analyzed. To observe the overall effect of these actions, the momentaxial force interaction diagrams are drawn. It is observed that the presence of axial force even in a small value can change the behavior of the connection significantly. It is also shown that the axial forces can alter the failure mode of the connection; and therefore it could result in a different than the predicted moment capacity of the connection.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.5
• /
• pp.37-46
• /
• 2007

This is the second of two companion papers that describe non-prismatic beam element for nonlinear seismic analysis of steel moment frames. Described in a companion paper is the formulation of a non-prismatic beam element to model the elastic and inelastic behavior of steel beams, which have reduced beam sections(RBS). This study describes the determination of yield surfaces, stiffness parameters, and hardening (or softening) rule parameters for RBS beam element. Analytical results of the RBS beam element show good correlation with test data and Finite Element Method(FEM) results.

• Journal of Microbiology and Biotechnology
• /
• v.17 no.4
• /
• pp.673-676
• /
• 2007

A two-step triplex PCR assay targeting the mecA, femA, and nuc genes was developed for the detection of methicillin resistance genes harbored by some Staphylococcus aureus isolates and for the simultaneous identification of such isolates at the species level. The triplex PCR revealed the presence of the femA and nuc genes in all the S. aureus isolates examined (n=105). Forty-four clinical isolates were mecA positive and no foodborne isolates were mecA positive. The PCR results had a 98 or 99% correlation with the results of PBP2a latex agglutination tests or oxacillin susceptibility tests, respectively.

• Transactions of Materials Processing
• /
• v.22 no.7
• /
• pp.383-388
• /
• 2013

Metal flow of the beam blank during H-beam rolling was examined in order to correlate the rolling defects with the beam blank configuration. For this purpose, H-beam rolling was performed on the beam blank where stainless steel bolts were inserted as the marker at the web and flange. The positional variation of the marker was monitored at each rolling pass, and the result was compared with the 3D FEM simulation employing the point tracking function. The simulation results were reasonably agreed with the experimental within the error of 0.5~1mm on both web and flange of the H-beam. It is anticipated that the 3D FEM simulation employing the point tracking function provides the guidance information on analyzing the correlation between the rolling defects and the beam blank configuration in H-beam rolling.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.7A
• /
• pp.1050-1056
• /
• 2000

In this paper, We Propose the automobile license plate extraction method using Discrete Cosin Transform and Correlation fem automobile image obtained through digital camera. The automobile license plate is consisted of the character and rectangle background of it. We extracted the automobile edge image by the DCT processing of automobile image and Obtained the automobile license plate from the automobile edge image by Correlation processing. We separated characters from automobile license plate using the projection histogram. Compare to the previous methods, we obtained the good result from extracting the automobile license plate at night, very strong light and bad weather.

• Progress in Superconductivity and Cryogenics
• /
• v.13 no.1
• /
• pp.46-50
• /
• 2011

The electrical insulation design of high voltage superconducting fault current limiters (SFCLs) should be confirmed to be applied for the stabilization of the power grid. This paper describes numerical analysis and AC dielectric experiments for developing high voltage SFCLs. The electric field distributions between applied high voltage part and ground were calculated by finite element method (FEM) simulation tool and AC criterion of liquid nitrogen at 200 kPa was calculated from correlation between the field utilization factor and FEM simulation results. This paper deals with ceonceptual insulation design of a 154 kV class single-phase no-inductively wound solenoid type SFCL which was focused on gap distance between the cryostat and superconducting coils. Furthermore, the shield ring effect was confirmed to reduce maximum electric field at applied high voltage part.

• Structural Engineering and Mechanics
• /
• v.60 no.1
• /
• pp.163-173
• /
• 2016

Nowadays using Carbon Fiber Reinforced Polymer (CFRP) has been expanded in strengthening steel structures. Given that few studies have taken about strengthening of steel hollow pipe sections using CFRP, in present study, the effects of CFRP sheets using two layers as well as in combination with additional reinforcing strips has been assessment. Strengthening of five specimens was carried out in laboratory tests. As well as numerical simulation was performed for all specimens by Finite Element Method (FEM) using ABAQUS software and high correlation between the results of numerical models with experimental data indicate the power of FEM in this field. The results of both laboratory and simulated specimens showed that load-bearing capacity of circular cross-sections can be significantly increased using CFRP retrofitting technique. Also, application of additional CFRP reinforcing strips and layers caused more strength for the strengthened specimens.

• Transactions of Materials Processing
• /
• v.23 no.4
• /
• pp.206-210
• /
• 2014

The metal lead frame, a semiconductor component, has product tolerances in micro units as compared to products made with a larger size mold. Therefore, small deflections of the mold and of the press as well as the press molding process itself have a strong influence on accuracy of the product. Hence, it is necessary for the process design to consider the structural response of the mold and the press during deformation. In the current study, the mold deflection and pressure on the punch is examined using the finite element modeling (FEM) program ABAQUS. The results from the simulation were verified with the dynamic deformation measurement equipment using digital image correlation (DIC).

• International Journal of Automotive Technology
• /
• v.8 no.5
• /
• pp.599-603
• /
• 2007

An efficient optimum design process has been developed and applied to systematically design a lock-up clutch system for a torque converter used in an automatic transmission. A simulated annealing algorithm was applied to determine the parameters of the compressive helical damper springs in the clutch. The determination of the number, location, a number of turns, and deflection of damper springs plays an important role in reducing vibration and noise in the lock-up system. Next, FE-based shape optimization was coded to find the shape of the clutch disk that would satisfy the strength, noise and vibration requirements. Using the optimum code, parametric studies were performed to see how spring diameters and frequencies of clutch systems changed as the damper spring traveling angles and the torques were varied. Based on the optimum results, five different designs for clutches with different springs were fabricated and vibration analyses and tests were conducted to validate the accuracy of the proposed method. Results from the two methods show a good correlation.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.595-600
• /
• 2009

Passengers in a vehicle feel uncomfortable due to squeal noise. Squeal noise, a kind of self-excited vibration, is generated by the friction force between the disc and the pad of the automobile. In this paper, modal analysis of wheel brake system was performed in order to prediction of squeal phenomenon. It was shown that the prediction of system instability is possible by FEM. Finite element model of that brake system was made. Some parts of a real brake was selected and modeled. The normal mode analysis method performs analyses of each brake system component. Experiment of modal analysis was performed for each brake components and experimental results were compared with analytical result from FEM. The complex eigenvalue analysis results compared with braking test. The analysis results show good correlation with braking test for the squeal frequency at an unstable mode.