• Steel and Composite Structures
• /
• 제8권1호
• /
• pp.35-52
• /
• 2008

The paper investigates the seismic performance of a Partially-Restrained (PR) steel-concrete composite frame using the probabilistic approach. The analysed frame was tested at the ELSA laboratory of the Joint Research Centre of Ispra (Italy), while the representative beam-to-column composite connections were tested at the Universities of Pisa, Milan and Trento (Italy). The component modelling of both interior and exterior composite joints is described first, including the experimental-numerical validation. The Latin Hypercube method has been used to draw the probabilistic distribution curves of joints, and then the whole PR composite frame has been analysed. Pushover and incremental dynamic analyses have been carried out using the non-linear FE code SAP2000 version 9.1. The fragility and performance curves of the PR composite frame have been determined for four damage limit states.

• Structural Engineering and Mechanics
• /
• 제21권3호
• /
• pp.295-313
• /
• 2005

This paper evaluates the effective width of composite steel beams with precast hollowcore slabs numerically using the finite element method. A parametric study, carried out on 27 beams with different steel cross sections, hollowcore unit depths and spans, is presented. The effective width of the slab is predicted for both the elastic and plastic ranges. 8-node three-dimensional solid elements are used to model the composite beam components. The material non-linearity of all the components is taken into consideration. The non-linear load-slip characteristics of the headed shear stud connectors are included in the analysis. The moment-deflection behaviour of the composite beams, the ultimate moment capacity and the modes of failure are also presented. Finally, the ultimate moment capacity of the beams evaluated using the present FE analysis was compared with the results calculated using the rigid - plastic method.

• 전기학회논문지P
• /
• 제55권2호
• /
• pp.110-114
• /
• 2006

This paper describes the accident analysis by modelling the current transformer mounting in a metal-clad switchgear at 22.9kV. In analyzing the accident, the reconstruction at the current transformer mounting(VCB connecting guide) has to be taken into account. The accident was modelled as a 3-phase ground fault occurring between the end plate of 22.9kV lines and the safety shutter at the current transformer mounting of the VCB inside the metal clad switchgear. Since the outside maintenance of the metal clad switchgear is restricted by the enclosed compartments, Its circumference has to be kept clean. Through the reconstruction results, it was confirmed that the fault of the enclosed switchboard could be reduced when the shutter made of Fe material was chanted into an insulation.

• Structural Monitoring and Maintenance
• /
• 제5권4호
• /
• pp.429-443
• /
• 2018

Fatigue is a principal failure mode for steel structures, and it is still less understood than any other modes of failure. Fatigue life estimation of metal bridges is a major issue for making cost effective decisions on the rehabilitation or replacement of existing infrastructure. The fatigue design procedures given by the standard codes are either empirical or based on nominal stress approach. Since the fatigue life estimation through field measurements is difficult and costly, more researches are needed to develop promising techniques in the fatigue analysis of bridges through Finite Element Analysis (FEA). This paper aims to develop a methodology for the Fatigue life estimation of railway steel bridge using FEA. The guidelines of IIW-1823-07 were used in the development of the methodology. The Finite Element (FE) package ANSYS and the programming software MATLAB were used to implement this methodology on an Indian Railway Standard (IRS) welded plate girder bridge. The results obtained were compared with results from published literature and found satisfactory.

• Structural Engineering and Mechanics
• /
• 제62권1호
• /
• pp.21-31
• /
• 2017

Engineered Cementitious Composite (ECC) is a special class of the new generation of high performance fiber reinforced cementitious composites (HPFRCC) featuring high ductility with relatively low fiber content. In this research, the mechanical performance of ECC beams will be investigated with respect to the effect of slag and aggregate size and amount, by employing nonlinear finite element method. The validity of the models was verified with the experimental results of the ECC beams under monotonic loading. Based on the numerical analysis method, nonlinear parametric study was then conducted to evaluate the influence of the ECC aggregate content (AC), ECC compressive strength ($f_{ECC}$), maximum aggregate size ($D_{max}$) and slag amount (${\phi}$) parameters on the flexural stress, deflection, load and strain of ECC beams. The simulation results indicated that when increase the slag and aggregate size and content no definite trend in flexural strength is observed and the ductility of ECC is negatively influenced by the increase of slag and aggregate size and content. Also, the ECC beams revealed enhancement in terms of flexural stress, strain, and midspan deflection when compared with the reference beam (microsilica MSC), where, the average improvement percentage of the specimens were 61.55%, 725%, and 879%, respectively. These results are quite similar to that of the experimental results, which provides that the finite element model is in accordance with the desirable flexural behaviour of the ECC beams. Furthermore, the proposed models can be used to predict the flexural behaviour of ECC beams with great accuracy.

• Computers and Concrete
• /
• 제33권1호
• /
• pp.103-119
• /
• 2024

In this paper, the non-linear behavior of masonry-infill and bare steel frames using different beam-column connections under monotonic static loading was investigated through a parametric study. Numerical models were carried out using one- and two-dimensional modelling to validate the experimental results. After validating the experimental results by using these models, a parametric study was carried out to model the behavior of these frames using flushed, extended, and welded connections. The results showed that using the welded or extended connection is more efficient than using the flushed type in masonry-infilled steel frames, since the lateral capacities, initial stiffness, and toughness have been increased by 155%, 601%, and 165%, respectively in the case of using welded connections compared with those used in bare frames. The FE investigation was broadened to study the influence of the variation of the uniaxial column loads on the lateral capacities of the bare/infill steel frames. As the results showed when increasing the amount of uniaxial loading on the columns, whether in tension or compression, causes the lateral load capacity of the columns to decrease by 26% for welded infilled steel frames. Finally, the influence of using different types of beam-to-column connections on the vertical capacities of the bare/infill steel frames under settlement effect was also studied. As a result, it was found that, the vertical load capacity of all types of frames and with using any type of connections is severely reduced, and this decrease may reach 62% for welded infilled frames. Furthermore, the flushed masonry-infilled steel frame has a higher resistance to the vertical loads than the flushed bare steel frame by 133%.

• 한국전산구조공학회논문집
• /
• 제27권3호
• /
• pp.147-154
• /
• 2014

충격 및 폭발하중으로 인한 위험으로부터 구조물의 안정성을 확보하기 위한 필요성의 증대에 따라 고율변형을 받는 콘크리트의 거동은 중요한 연구주제가 되었다. 콘크리트의 고율변형 거동은 정적인 상태와는 다른 독특한 거동을 보이기 때문에 다양한 고율변형모델들이 제안되어 고율변형 상태를 수치해석하는데 사용되고 있다. 이러한 수치해석 과정에서 발생하는 문제가 요소의 크기에 따라 수치해석결과가 크게 변하는 요소의존성 문제이다. 본 논문에서는 파괴에너지이론에 기초하여 요소의존성을 최소화할 수 있는 기준식을 제안하고 HJC(Holmquist Johnson Cook)모델을 이용한 관통수치해석을 통해 기준식을 검증하였다. 그 결과 기준식을 통해 산정된 파괴변형률을 수치해석상에 적용해줌으로써 해석결과의 요소의존성이 감소하였고 해의 정확성 또한 향상되는 것을 파악할 수 있었다.

• 암석학회지
• /
• 제4권1호
• /
• pp.49-58
• /
• 1995

춘양 화강암체 주변의 두음리층 변성이질암내에서 십자석-흑운모-홍주석-석류석 (SBAG)광물 조합과 부광물 조합(SBA 및 SBG)이 홍주석과 십자석대에 걸쳐 흔히 산출한다. SBAG 광물 조합은 KFMASH($K_2O-FeO-MgO-Al_2O_3-SiO_2-H_2O$) 모델 계에서 자유도가 1이기 때문에 광역적으로 산출하기 힘들다. 이 SBAG (부)광물 조합의 평형 관계를 밝히기 위하여 투영법과 특이치 분해법(Singular Value Decomposition, SVD, method)을 사용하였다. SBAG 광물 조합을 가지는 단일 시료는 SVD 모델 반응식을 보이지 않으면 비-KFMASH성분에 의해 안정되었음을 나타낸다. 한편, SBAG 및 부광물 조합은 AFM-Mn 성분공간 내에서 서로 교차하기 때문에 반응 관계를 시사한다. 그러나 SVD 모델링은 이들 사이에 반응 관계를 지지하지 못한다. 그러므로, SBAG와 부광물 조합은 전암 성분이나 ${\mu}_{H20}$의 차이에 의해 두음리층에서 비교적 넓게 산출함을 알수 있다. 두음리층이 홍주석대 및 규선석대에서 십자석이 안정함을 석류석-사정석-흑운모-백운모 지압계를 사용하여 구한 변성 압력과도 일치한다.

• Structural Engineering and Mechanics
• /
• 제28권1호
• /
• pp.107-127
• /
• 2008

Wind turbine blades are increasing in magnitude without a proportional increase of stiffness for which reason geometrical and inertial nonlinearities become increasingly important. Often these effects are analysed using a nonlinear truncated expansion in undamped fixed base mode shapes of a blade, modelling geometrical and inertial nonlinear couplings in the fundamental flap and edge direction. The purpose of this article is to examine the applicability of such a reduced-degree-of-freedom model in predicting the nonlinear response and stability of a blade by comparison to a full model based on a nonlinear co-rotating FE formulation. By use of the reduced-degree-of-freedom model it is shown that under strong resonance excitation of the fundamental flap or edge modes, significant energy is transferred to higher modes due to parametric or nonlinear coupling terms, which influence the response and stability conditions. It is demonstrated that the response predicted by such models in some cases becomes instable or chaotic. However, as a consequence of the energy flow the stability is increased and the tendency of chaotic vibrations is reduced as the number of modes are increased. The FE model representing the case of infinitely many included modes, is shown to predict stable and ordered response for all considered parameters. Further, the analysis shows that the reduced-degree-of-freedom model of relatively low order overestimates the response near resonance peaks, which is a consequence of the small number of included modes. The qualitative erratic response and stability prediction of the reduced order models take place at frequencies slightly above normal operation. However, for normal operation of the wind turbine without resonance excitation 4 modes in the reduced-degree-of-freedom model perform acceptable.

• Journal of Electrical Engineering and Technology
• /
• 제10권1호
• /
• pp.155-164
• /
• 2015

In this paper, two rotor configurations including different amount of magnet and reluctance parts are presented. The rotors are constituted by means of a flexible hybrid motor structure. Considerable features of the hybrid structure are that the combination of the magnet and reluctance parts can be suitably modified and the mechanical angle (${\beta}$) between the parts can also be varied. Two hybrid rotor configurations have been considered in this study. First, finite element (FE) simulations were carried out and the torque behaviors of the motors were predicted. The average torque ($T_{avg}$) and maximum torque ($T_{max}$) curves were obtained from FE simulations in order to find suitable ${\beta}$. Mathematical model of the motors was formed in terms of a,b,c variables considering the amount of the magnet and reluctance parts on the rotor and simulations were performed. Rotor prototypes, motor drive and drive method were introduced. Torque profiles of the motors were obtained by static torque measurement and loaded tests were also realized. Thus, simulation results were verified by experimental study. There is a good match between predictions and measurements. The proposed motors are operated with electrical $120^{\circ}$ mode as a brushless DC motor (BLDC) and torque versus speed characteristics show a compound DC motor characteristic. The motors can be named as brushless DC compound motors.